Transcript
www.ZKTeco.com
Safety Precautions What’s in a Box Product PIN Diagram
LED indicators Product Dimensions Installation of Panel with Casing Wiring Legend Power Wiring Diagram
FR1200 Connection Weigand Connection Exit button Connection Lock connection Door Sensor Connection Aux. Input Connection Aux. Output Connection Ethernet Connection RS485 Connection
DIP switch settings Electrical Specifications Troubleshooting Specifications
1
02 04 06 06 07 08 09 10 11 12 12 13 13 15 15 16 17 18 19 20 21
1Safety Precautions The list below is to keep user’s safety and prevent any loss. Please read carefully before installation.
01
Do not install the device in an area subject to direct sun light, Humidity or dust
04
Be careful not to let liquid like water, drinks or chemicals leak inside the device.
02
03
Do not place the device next to heating equipments
Do not place a magnet near the product. Magnetic objects such as magnet, CRT, TV, monitor or speaker may damage the device.
05
06
Clean the device often to remove dust on it
2
Do not let children touch the device without supervision.
Safety Precautions The list below is to keep user’s safety and prevent any loss. Please read carefully before installation.
07
08
Do not drop the device.
10
Do not damage the device
09
Do not disassemble, repair or alter the device.
11
Do not use the device for any other purpose than specified.
12
In cleaning, do not splash water on the device but wipe it out with smooth cloth or towel.
3
Contact your nearest dealer in case of a trouble or problem.
Product Contents Basic Contents
Wall Mounting Screws – 2 pcs.
Wall Plugs– 2 pcs.
Screw Driver – 2 pcs.
Software CD
Inbio260 4
Surge Suppressing Diode– 4 pcs.
InBio Installation Guide
Product Contents Optional accessories
Weigand Card Reader
ZK4500 FP Enrollment reader
Prox Card
Card Enroller
5
FR1200 FP Reader
K1-1 Exit Button
Inbio Metal Case
RS485 convertor
Product PIN Diagram LED indicators
SD Card Slot LINK LED Ethernet Port
ACT LED
Aux Input 1
LINK (Green)
LED solid green indicates TCP/IP communication is normal
ACT (Yellow)
Flashing LED indicates data communication is in progress
EXT RS485 (Yellow & Green)
Flashing LED indicates data communication in progress
PC RS485 (Yellow & Green)
Flashing LED indicates data communication is in progress
POWER (Red)
Flashing LED indicates the panel is powered on.
RUN (Green)
Flashing LED indicates that panel is in normal working mode
CARD (Yellow)
Flashing LED indicates that the card is read by the panel.
Aux Input 2 FR1200 Fingerprint Reader
DIP Switch State Indictor PC RS485 Port Aux Output 1
#1 Door Exit Button
#1 Door Card Reader1
Aux Output 2 #1 Door Sensor
#1 Door Card Reader2
#1 Door Lock #2 Door Sensor #2 Door Lock Lock Power
#2 Door Exit Button #2 Door Card Reader1
Inbio Power
#2 Door Card Reader2
6
Product Dimension Inbio260
106mm (4.17in.)
106mm (4.17in.) 36mm (1.42in.)
Dimensions(L*W*H):185.1× 106× 36（mm） 7.29× 4.17× 1.42(inches)
185.1mm (7.29in.)
InBio-Casing
330mm (13.0in.)
330mm (13.0in.) 90.5mm (3.56in.)
Dimensions(L*W*H): 400 *90.5*330（mm） 15.7× 13.0× 3.56(inches)
400mm (15.7in.)
7
Installation of Panel & Case Metal Case
8
Wire Legend Infrared sensors FR1200
Inbio-Case
#1Exit Button
#1Card Reader1
#2 Exit Switch
#2 Card Reader1
DC
Detector
12V DC Power 12V
Network
RS485 Convertor Floodlight Alarm Normally Close Lock Normally Open Lock Power Supply
9
Power wiring diagram Without Backup Battery
AC
Inbio260 110-220V
AC
Switching power supply
With Backup Battery AC
Inbio260 110-220V
+ Backup Battery
-
AC
Switching power supply
10
FR1200 Connection
12V DC 12V DC
#1 FR1200
DIP Switch Setting For FR1200 Device ID
#2 FR1200
#3 FR1200
#4 FR1200
Important Notes 1. There are six DIP switches on the back of FR1200 , Switches 1-4 is for RS485 address , switch 5 is reserved , switch 6 is for reducing noise on long RS485 cable. 2. Set the odd number for IN reader, and the even number for OUT reader(for eg. For two readers for one door- the RS485 address 1 is for IN reader, RS485 address 2 is for OUT reader ) 3. If FR1200 is powered from Inbio260 panel ,the length of wire should be less than 100 meters or 330 ft. 4. The External RS485 interface can supply maximum 500mA current , The FR1200’s startup current is 240mA. So Inbio260 only can only power two FR1200s. 5. If the cable length is more than 200 meters or 600 ft , the number 6 switch should be ON as below Distance More than 200 meters
11
Weigand Connection Beeper Green LED Weigand D1
Weigand D0 GND DC+(6-14V)
Weigand Card Reader
Exit Button Connection
12V DC Power Supply
DV12V（+）
DV12V（-） BUT
NO
GND
COM NC
ZK ABK Exit Button
Notice： separate power supply
12
K1-1 Exit Switch
Lock Connection For Normally Open -Lock powered from panel power supply
FR107
GND 12V DC Sensor Sensor
GND 12V DC
FR107
For Normally Closed -Lock powered from panel power supply
12V DC GND
Sensor Sensor
GND 12V DC
13
Lock Connection Switching Wet Contact to Dry Contact Important Notes: InBio is set to supply lock power by default from built-in power supply , If you want to use external power supply , you must take the following steps 1. Take apart the cover of inbio460 2. Select the desired lock relay and find its jumpers 3. Take off the jumpers and change to 4. Connect the lock as shown in the diagram below.
Steps:
Detach from Rail
Inbio260
5
1
5
Changed Setting
Lock Relay
Remove Top Cover
5
1 Jumpers
Terminals
1
5
1
Default Setting
Connecting a Lock with External Power supply
GND 12V DC
FR107
SEN SEN GND
14
12V DC
Auxiliary Input/Output Aux. Input Connection
Smoke Detector 12V DC GND COM NO NC
Aux. output Connection
Alarm 12V DC GND COM NO NC
15
Ethernet Connection Important Notes:
TCP/IP
1. Both 10Base-T and 100Base-T are supported 2. The cable length must be less than 100 meters or 330 ft.
ZK4500 Enrollment reader CR10 Card Issuer
3. For more than 100 meters , please use HUB to amplify the signal
The CR10 and ZK4500 are connected to the server using USB connection.
Direct connection To connect Inbio260 with a PC directly, connect both devices with a straight network cable. As the Inbio260 supports auto MDI/MDIX , it is not necessary to use a crossover type cable.
ZK4500 Enrollment reader CR10 Card Issuer
16
RS485 Connection
#63 Inbio260
#1 Inbio260
Important Notes
Do's and Dont's for RS 485 connection
1. RS485 communication wires should be a shielded or twisted pair cable. RS485 communication wires should be connected in a bus cascade instead of a star form, to achieve a better shielding effect by reducing signal reflection during communications. 2. A single 485 bus can be connected with 63 access control panels at the most, but preferably less than 32 panels should be connected. 3. To eliminate signal attenuation in communication cables and suppress interference, if the bus is longer than 200 meters, set the number 8 DIP switch to the ON position. This is equivalent to a parallel connection of one 120ohm resistance between the 485+ and 485- lines. Distance More than 200 meters #1 Inbio260
RS485RS485+ GND
#* Inbio260
17
DIP Switch Setting Introduction
RS485 Address 1. Number 1-6 are reserved to set the device number for RS485 communication. The code is binary, and the numbering starts from left to right. When the switch is set to ON position, it indicates 1 (on); when the switch is set downwards, it indicates 0 (off). For example, to set a device number 39=1+2+4+32, which corresponds to the binary code 111001, put number 1, 2, 3, and 6 to ON position, as illustrated below.
2. For more details, please check the table at the end of this document
Restore factory setting
Terminal Resistance
1. If you forget the inBio IP address or the device does not work normally, you can use the number 7 terminal to restore inbio260 to factory default settings. The parameters which gets reset are device IP address, communication password ,gateway ,subnet mask. 2. The switch is OFF by default. When it is moved upwards and downwards for three times within 10 seconds and finally returned to OFF position, the factory settings will be restored after the access control panel is restarted.
1. Number 8 is for setting the RS485 termination resistance. Putting the switch to ON position is equivalent to parallel connection of a 120ohm termination resistance between 485+ and 4852. As shown in diagram below, for more info please read RS485 connection important notes
1 times
2 times
3 times
OFF
120ohm
18
Electrical Specification Min.
Typ.
Max.
Notes
9.6
12
14.4
Use regulated DC power adaptor only
Working power supply Voltage(V) Current(A)
2
Electronic lock relay output Switching voltage(V)
36V
Switching Current(A)
2
Use regulated DC power adaptor only
Auxiliary relay output Switching voltage(V)
36V
Switching Current(A)
1.25
Use regulated DC power adaptor only
Switch Aux. input VIH (V)
TBD
VIL (V)
TBD
Pull-up resistance (Ω)
4.7k
The input ports are pulled up with 4.7k resistors
WEIGAND Input Voltage(V)
10.8
12
Current(mA)
13.5 500
ZK Electronic lock Voltage(V) Current(mA)
10.8
12
13.2 500
19
Troubleshooting 1.
Fingerprint can not be read well or it takes too long. Check whether a finger or fingerprint sensor is stained with sweat, water, or dust Retry after cleaning the finger and fingerprint sensor with dry cloth. If a finger is way too dry, rub your finger on the palm and retry. Try to reset fingerprint sensor by pressing the reset button at the bottom of the reader
2. Fingerprint is matched but authorization keeps failing. Check whether the user’ access is restricted. Inquire with administrator whether the enrolled fingerprint has been deleted from the device for some reason. 3. How Many kinds of WEIGAND format can be supported. The panel is set to read 26 bit by default. However there are 9 other bit formats which can be selected from the software. In addition you can also define your custom bit format. 4.
How many verification modes can be support. Card Only Fingerprint Only Password Only Card plus fingerprint Card plus password Card or fingerprint
20
Reset Button
Specification Communication
RS485, Ethernet
Baud Rate for RS485
9600-115200 baud
Power Supply
12V DC, 3A
Device Capacity
Card capacity 30,000 ; Log events capacity 100,000 ; Finger capacity 3,000
LED Indicator
Indication for communication, power, status and prox card
Environment
Operating Temp: 32-113 °F (0-45 °C)
Number of doors controlled
two door one way or two door two way
Number of card readers supported
4
Number of FR1200 supported
4
FR1200 Sensor
Fingerprint sensor 500dpi Optical / Optical sensor
Types of readers supported
26-bit Weigand, others upon request
Number of Inputs
6(2 Exit Device, 2Door Status, 2 AUX)
Number of Outputs
4 (2- Form C relay for lock and 2- Form C relay for Aux output)
Weight
7.8lbs (3.55kg)
Enclosure
Stainless Steel
Mounting
Wall Mount
Dimensions (Bundle Only)
15.7in. × 3.56in.× 13.0in. 400mm(L) X 90.5mm(W) X 330mm(H)
Dimensions ( Board Only)
8.89in.× 4.17in.× 1.42in. 226mm(L) X 106mm(W) X 36mm(H)
CPU
32 bit 400MHz
RAM
32MB
Flash
128MB
Certified
21
Operating Humidity: 20% to 80%
PC485 Table
Switch Setting
Switch Setting
Place Address
Place Address
1
2
3
4
5
6
1
2
3
4
5
6
Address No.
1
2
4
8
16
32
Address No.
1
2
4
8
16
32
01
ON
OFF
OFF
OFF
OFF
OFF
33
ON
OFF
OFF
OFF
OFF
ON
02
OFF
ON
OFF
OFF
OFF
OFF
34
OFF
ON
OFF
OFF
OFF
ON
03
ON
ON
OFF
OFF
OFF
OFF
35
ON
ON
OFF
OFF
OFF
ON
04
OFF
OFF
ON
OFF
OFF
OFF
36
OFF
OFF
ON
OFF
OFF
ON
05
ON
OFF
ON
OFF
OFF
OFF
37
ON
OFF
ON
OFF
OFF
ON
06
OFF
ON
ON
OFF
OFF
OFF
38
OFF
ON
ON
OFF
OFF
ON
07
ON
ON
ON
OFF
OFF
OFF
39
ON
ON
ON
OFF
OFF
ON
08
OFF
OFF
OFF
ON
OFF
OFF
40
OFF
OFF
OFF
ON
OFF
ON
09
ON
OFF
OFF
ON
OFF
OFF
41
ON
OFF
OFF
ON
OFF
ON
10
OFF
ON
OFF
ON
OFF
OFF
42
OFF
ON
OFF
ON
OFF
ON
11
ON
ON
OFF
ON
OFF
OFF
12
OFF
OFF
ON
ON
OFF
OFF
43
ON
ON
OFF
ON
OFF
ON
13
ON
OFF
ON
ON
OFF
OFF
44
OFF
OFF
ON
ON
OFF
ON
14
OFF
ON
ON
ON
OFF
OFF
45
ON
OFF
ON
ON
OFF
ON
15
ON
ON
ON
ON
OFF
OFF
46
OFF
ON
ON
ON
OFF
ON
16
OFF
OFF
OFF
OFF
ON
OFF
47
ON
ON
ON
ON
OFF
ON
17
ON
OFF
OFF
OFF
ON
OFF
48
OFF
OFF
OFF
OFF
ON
ON
49
ON
OFF
OFF
OFF
ON
ON
50
OFF
ON
OFF
OFF
ON
ON
51
ON
ON
OFF
OFF
ON
ON
52
OFF
OFF
ON
OFF
ON
ON
53
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
OFF
ON
ON
18 19 20 21 22
OFF ON OFF ON OFF
ON ON OFF OFF ON
OFF OFF ON ON ON
OFF OFF OFF OFF OFF
ON ON ON ON ON
OFF OFF OFF OFF OFF
23
ON
ON
ON
OFF
ON
OFF
54
24
OFF
OFF
OFF
ON
ON
OFF
55
ON
ON
ON
OFF
ON
ON
25
ON
OFF
OFF
ON
ON
OFF
56
OFF
OFF
OFF
ON
ON
ON
26
OFF
ON
OFF
ON
ON
OFF
57
ON
OFF
OFF
ON
ON
ON
OFF
58
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
27
ON
ON
OFF
ON
ON
28
OFF
OFF
ON
ON
ON
OFF
59
29
ON
OFF
ON
ON
ON
OFF
60
OFF
OFF
ON
ON
ON
ON
30
OFF
ON
ON
ON
ON
OFF
61
ON
OFF
ON
ON
ON
ON
31
ON
ON
ON
ON
ON
OFF
62
OFF
ON
ON
ON
ON
ON
32
OFF
OFF
OFF
OFF
OFF
ON
63
ON
ON
ON
ON
ON
ON
22
Functions and specifications of the product are subject to change without notice due to quality enhancement or function update. For any inquiry for the product, please contact ZKTeco Inc .
Copyright 2013 ZKTeco Inc. All right reserved. ZKTeco May, at any time and without notice , Make changes or improvements to the product and services offered and/or cease producing or commercializing them.
ZK China : ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town, Longgang District, Shenzhen China. Tel.: +86 755-89602345
[email protected] zkteco.com
