Transcript
POLISH MARK
www.camsat-cctv.com
EU
www.camsat-cctv.com
Application Example 2 3 units of X-CAMswitch send the signal from the 10 IP cameras.
Power supply*
Power supply*
IP IP
CAMERA 4 CAMERA 3 CAMERA 2
QUICK START
Power supply*
CAMERA 1
LAN
IP
- Outdoor PoE Switch
NVR
X-CAMswitch
- Outdoor PoE Switch
X-CAMswitch
- Outdoor PoE Switch
X-CAMswitch
Ver. 1.0
CAMERA 1
IP IP IP
IP
CAMERA 4
CAMERA 4
IP
CAMERA 3
CAMERA 3
IP
CAMERA 2
CAMERA 2
IP
Power cable Twisted-pair cable with RJ45 sends signal from X-CAMswitch (cameras) to recorder
External hermetic network PoE switch for IP cameras powered by 12-48V DC or PoE
CAMERA 1
Twisted-pair cable with RJ45 (Ethernet), sends signal from camera to X-CAMswitch Twisted-pair cable with Rj45 (Ethernet), connecting X-CAMswitch (with no cables connected 4 - blue, 5 - white-blue, 7 - white-brown, 8 - brown)
1. Specifications X-CAMswitch is a 4-port, external PoE switch working in LAN 10/100 Base-T. It allows you to connect to the LAN, and power 4 IP PoE cameras. Each PoE port is protected independenly by automatic fuse. X-CAMswitch / 12 has a power input 12-48V AC / DC, which allows you to connect a standard 12V DC or AC adapter from the PTZ camera 24V AC.
* Depending on version: 12V - 48V DC in X-CAMswitch/12 48V DC in X-CAMswitch/48
Product Specification Application Example 3 X-CAMswitch powers the wireless CDS-6IPeco (Tx) and supplies by the PoE and transmits the signal from 3 IP cameras. CDS-6IPeco (Tx) sends a radio signal to the receiver CDS-6IPeco (Rx). To power the whole system you need only one power supply from 12 to 48V DC. CDS-6IPeco
CDS-6IPeco
(or other IP module)
Maximum power consumption of cameras
4 x 15,4W (with power supply 24V-48V) 4 x 8W (with power supply 12V)
Input voltage supply
. X-CAMswitch/12 - 12-48 V AC/DC or 48 V PoE . X-CAMswitch/48 - 48 V DC or 48 V PoE
PoE power type
Passive PoE (+4,5 48V) (-7,8 GND) pin
PoE cable lenght
< 100 m
Protection
Automatic fuses on each PoE port
Degree of protection
IP 65
Temperatura pracy
-20° C ÷ 55° C
Size
140x180x60 mm (W x H x D)
PoE (48V/24V) (Pmax<25W)
+LAN
2000m
NVR
LAN
3 x LAN PoE OUT (48V) – IP cameras 1 x LAN PoE OUT (48V/24V) – IP camera or radio module 1xLAN PoE IN (48V) – power input from PoE recorder or PoE powe supply
POWER IN 48V
POWER IN - Outdoor PoE Switch
(or other IP module)
X-CAMswitch
Ethernet Ports 10/100 Mbps
Power supply*
LAN + PoE 24 PoE 24V power supply (in set with CDS-6IPeco)
LAN + PoE 24V
IP
CAMERA 1 (PoE + LAN) CAMERA 2 (PoE + LAN)
Power cable Twisted-pair cable with RJ45 sends signal from X-CAMswitch (cameras) to recorder
Switch set in Radio position sends PoE 24V DC voltage to power IP radio module.
CAMERA 3 (PoE + LAN)
IP IP
* Depending on version: 12V - 48V DC in X-CAMswitch/12 48V DC in X-CAMswitch/48
4
For more information about the product on www.camsat-cctv.com
For more information about the product on www.camsat-cctv.com
1
www.camsat-cctv.com
QUICK START 2. Includes - PoE network switch X-CAMswitch - Clamps - Manual - Declaration of conformity
x1 x2 x1 x1
pc. pcs. pc. pc.
Depending on the version of the device, the X-CAMswitch has the following power inputs: X-CAMswitch/12 - can be powered from 12V-48V DC or AC adapter for the PTZ camera 24V AC (Note: with the 12V power supply maximum power of the cameras is 4x8W). X-CAMswitch/48 - can be powered from an AC adapter 48V DC or 48V PoE (Maximum power of cameras 4x15,4W).
3. Description of the connectors and LEDs
POWER IN
PoE (48V/24V) POWER IN 48V (Pmax<25W)
+LAN
4. Preparing for operation X-CAMSwitch device can be connected to the power supply in two ways Option 1 - directly from the power supply 12-48V. Option 2 - X-CAMSwitch powered from adapter PoE48V.
WARNING
The device should not be installed in direct sunlight.
5. Connect the radio module with PoE24V WARNING
Before connecting the radio to the port CAMERA 4 / RADIO switch voltage PoE 48V to PoE 24V (use switch located next to the switch. Voltage of 48V may causedamage incompatible device!
Application Example 1 X-CAM switch sends signal from 4 IP cameras to NVR. Additionally it is a power supply 4 IP PoE 48V cameras. X-CAMswitch PoE (48V/24V) POWER IN 48V
POWER IN
- Outdoor PoE Switch
(Pmax<25W)
+LAN
DESCRIPTION OF CONNECTORS AND LED INDICATORS POWER IN 12-48V - input DC or AC (the red POWER LED indicates the appearance of voltage on the connector)
Power supply*
POWER IN 48V - power supply input used only to power the device with another switch or PoE power supply (the red POWER LED indicates the appearance of voltage on the connector) CAMERA 4/LAN – LAN port to power IP camera (PoE 48V) or device configuration. PoE voltage on output is controlled by above switch (the value of voltage is shown by red-green LED PoE ON/PoE OFF; blinking LINK diode shows data transfer status) CAMERA 3 – LAN port to power the IP camera (PoE 48V) ((the red POWER LED indicates the appearance of voltage on the connector; blinking LINK diode shows data transfer status) CAMERA 2 – LAN port to power the IP camera (PoE 48V) ((the red POWER LED indicates the appearance of voltage on the connector; blinking LINK diode shows data transfer status) CAMERA 1 – LAN port to power the IP camera (PoE 48V) (the red POWER LED indicates the appearance of voltage on the connector; blinking LINK diode shows data transfer status)
CAMERA 1 (PoE + LAN)
Switch set in Camera 4 transmits PoE voltage of 48V DC to power camera 4.
NVR
CAMERA 2 (PoE + LAN) LAN
CAMERA 3 (PoE + LAN) CAMERA 4 (PoE + LAN)
Power cable Twisted-pair cable with RJ45 sends signal from X-CAMswitch (cameras) to recorder
IP
IP IP IP
Twisted-pair cable with RJ45 (Ethernet), sends signal from camera to X-CAMswitch Twisted-pair cable with Rj45 (Ethernet), connecting X-CAMswitch (with no cables connected 4 - blue, 5 - white-blue, 7 - white-brown, 8 - brown) * Depending on version:
12V - 48V DC in X-CAMswitch/12 48V DC in X-CAMswitch/48
2
For more information about the product on www.camsat-cctv.com
For more information about the product on www.camsat-cctv.com
3
