Transcript
X-WAV™ OUTDOOR WI-FI RANGE EXTENDER ANTENNA KIT QUICK INSTALL GUIDE diagram 3
TROUBLESHOOTING Weak or non-existent coverage. 1. Make sure the cables are properly connected and that there is power to the X-WAV Antenna and the EnGenius EOC1650. 2. Ensure that the X-WAV antenna is properly positioned. The antenna should be facing the direction of the area to be covered with a minimum of 2 feet (.6 meters) with no obstructions in front of the antenna. Luxul wireless signals are superior for penetrating wood, concrete, and stucco, but all wireless signals can be disrupted by certain obstructions, including large metal objects. Try orienting the antenna where more line-of-sight access to the desired coverage area is available. If after checking the above items, your X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit still does not seem to be functioning properly, please contact: Luxul Wireless Technical Support at:
[email protected] regarding Antenna. Luxul Wireless products include a Limited One Year Warranty Results may vary depending on building layout, type of construction and other environmental factors including Wi-Fi traffic, Microwaves Ovens, Cordless Phones, etc. FCC NOTICE: The use of all radio equipment is subject to regulations in each country. To comply with FCC part 15 rules in the United States, radio equipment must only be used in systems that have been FCC certified. It is the responsibility of the user/professional installer/operator to ensure that only approved equipment/systems are deployed. To ensure FCC part 15 compliance, Luxul amplifier products should only be installed in certified systems by licensed professionals. FCC Certification Support for OEMs: Luxul Wireless offers FCC certification assistance and engineering support for qualified OEM’s interested in certifying complete amplified WLAN systems. Please contact us for details.
LUXUL WIRELESS | 357 South 670 West, Lindon, UT, 84042 p: 801-822-5450 f: 801-822-5460 www.luxulwireless.com © 2009 Luxul Corp. All rights reserved.
LUX-QIG-100620090210-XWK124FP14
For use with the EOC1650 WAP Congratulations on your purchase of a Luxul Wireless X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit. X-WAV kits are simple to install. In just a few short steps, you will be able to enjoy the benefits of a farther reaching, clearer wireless signal.
LUXUL WIRELESS PRODUCTS COVERED BY THIS GUIDE XWK1-24-FP14 - X-WAV 2.4GHz Outdoor Wi-Fi Range Extender Antenna Kit
X-WAV™ KIT QUICK INSTALL GUIDE THE X-WAV™ OUTDOOR WI-FI RANGE EXTENDER ANTENNA KIT INCLUDES THE FOLLOWING: • • • •
X-WAV XW-24-FP14 14dBi High Gain 2.4GHz Flat Panel CPAntenna 36” Coax cable (N-Male to RP-SMA) HDW-AM-UOD outdoor mounting bracket Quick Install Guide
SET UP YOUR ENGENIUS EOC1650 See the EnGenius EOC1650 Wireless Access Point (WAP) and POE injector (EPE-1212) manual for set up instructions. Contact EnGenius directly for additional support or warranty information
POSITIONING YOUR X-WAV™ OUTDOOR RANGE EXTENDER KIT
GETTING STARTED: ADDITIONAL ITEM REQUIRED • EnGenius EOC1650 Wireless Access Point (WAP) Included with the EOC1650: 802.11b/g Long range AP/CB (EOC1650), POE injector (EPE1212), Power Adaptor, CD with User’s Manual, Quick Installation Guide(QIG), Metal strap, Special screwset. • External Ethernet cable from your data source/network (Max. length 329’ or 100 meters).
The X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit features a high gain directional antenna. Remember to consider the direction of the signal when positioning the X-WAV™ Antenna. The signal extends outward, away from the front of the antenna. Use diagram 2 below for suggestions on positioning your X-WAV™ Outdoor Antenna Kit for maximum Wi-Fi coverage.
NOTE: Disconnect all power before connecting or disconnecting any cables, coax or antennas to or from this device. Failure to do so will void your warranty.
SETTING UP YOUR X-WAV™ OUTDOOR WI-FI RANGE EXTENDER ANTENNA KIT Connecting the EnGenius EOC1650 to the Antenna (diagram 1) 1. Remove the connector cover on the back of the EOC1650 to access the antenna switch labeled INT - EXT 2. Set the switch to EXT to use the External Antenna port 3. Connect the RP-SMA end of the coax cable to the external antenna connector on the top of the EOC1650 4. Connect the N-Male connector of the coax cable to the antenna.
1 diagram 2
INT
EXT
MOUNTING YOUR X-WAV™ OUTDOOR RANGE EXTENDER KIT The X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit may be mounted to a pole using the included HDW-AM-UOD outdoor mounting bracket. See diagram 3 (Next page) for an example of the antenna mount set up. see the EnGenius EOC1650 Wireless Access Point (WAP) for mounting instructions.
diagram 1
X-WAV™ KIT QUICK INSTALL GUIDE THE X-WAV™ OUTDOOR WI-FI RANGE EXTENDER ANTENNA KIT INCLUDES THE FOLLOWING: • • • •
X-WAV XW-24-FP14 14dBi High Gain 2.4GHz Flat Panel CPAntenna 36” Coax cable (N-Male to RP-SMA) HDW-AM-UOD outdoor mounting bracket Quick Install Guide
SET UP YOUR ENGENIUS EOC1650 See the EnGenius EOC1650 Wireless Access Point (WAP) and POE injector (EPE-1212) manual for set up instructions. Contact EnGenius directly for additional support or warranty information
POSITIONING YOUR X-WAV™ OUTDOOR RANGE EXTENDER KIT
GETTING STARTED: ADDITIONAL ITEM REQUIRED • EnGenius EOC1650 Wireless Access Point (WAP) Included with the EOC1650: 802.11b/g Long range AP/CB (EOC1650), POE injector (EPE1212), Power Adaptor, CD with User’s Manual, Quick Installation Guide(QIG), Metal strap, Special screwset. • External Ethernet cable from your data source/network (Max. length 329’ or 100 meters).
The X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit features a high gain directional antenna. Remember to consider the direction of the signal when positioning the X-WAV™ Antenna. The signal extends outward, away from the front of the antenna. Use diagram 2 below for suggestions on positioning your X-WAV™ Outdoor Antenna Kit for maximum Wi-Fi coverage.
NOTE: Disconnect all power before connecting or disconnecting any cables, coax or antennas to or from this device. Failure to do so will void your warranty.
SETTING UP YOUR X-WAV™ OUTDOOR WI-FI RANGE EXTENDER ANTENNA KIT Connecting the EnGenius EOC1650 to the Antenna (diagram 1) 1. Remove the connector cover on the back of the EOC1650 to access the antenna switch labeled INT - EXT 2. Set the switch to EXT to use the External Antenna port 3. Connect the RP-SMA end of the coax cable to the external antenna connector on the top of the EOC1650 4. Connect the N-Male connector of the coax cable to the antenna.
1 diagram 2
INT
EXT
MOUNTING YOUR X-WAV™ OUTDOOR RANGE EXTENDER KIT The X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit may be mounted to a pole using the included HDW-AM-UOD outdoor mounting bracket. See diagram 3 (Next page) for an example of the antenna mount set up. see the EnGenius EOC1650 Wireless Access Point (WAP) for mounting instructions.
diagram 1
X-WAV™ OUTDOOR WI-FI RANGE EXTENDER ANTENNA KIT QUICK INSTALL GUIDE diagram 3
TROUBLESHOOTING Weak or non-existent coverage. 1. Make sure the cables are properly connected and that there is power to the X-WAV Antenna and the EnGenius EOC1650. 2. Ensure that the X-WAV antenna is properly positioned. The antenna should be facing the direction of the area to be covered with a minimum of 2 feet (.6 meters) with no obstructions in front of the antenna. Luxul wireless signals are superior for penetrating wood, concrete, and stucco, but all wireless signals can be disrupted by certain obstructions, including large metal objects. Try orienting the antenna where more line-of-sight access to the desired coverage area is available. If after checking the above items, your X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit still does not seem to be functioning properly, please contact: Luxul Wireless Technical Support at:
[email protected] regarding Antenna. Luxul Wireless products include a Limited One Year Warranty Results may vary depending on building layout, type of construction and other environmental factors including Wi-Fi traffic, Microwaves Ovens, Cordless Phones, etc. FCC NOTICE: The use of all radio equipment is subject to regulations in each country. To comply with FCC part 15 rules in the United States, radio equipment must only be used in systems that have been FCC certified. It is the responsibility of the user/professional installer/operator to ensure that only approved equipment/systems are deployed. To ensure FCC part 15 compliance, Luxul amplifier products should only be installed in certified systems by licensed professionals. FCC Certification Support for OEMs: Luxul Wireless offers FCC certification assistance and engineering support for qualified OEM’s interested in certifying complete amplified WLAN systems. Please contact us for details.
LUXUL WIRELESS | 357 South 670 West, Lindon, UT, 84042 p: 801-822-5450 f: 801-822-5460 www.luxulwireless.com © 2009 Luxul Corp. All rights reserved.
LUX-QIG-100620090210-XWK124FP14
For use with the EOC1650 WAP Congratulations on your purchase of a Luxul Wireless X-WAV™ Outdoor Wi-Fi Range Extender Antenna Kit. X-WAV kits are simple to install. In just a few short steps, you will be able to enjoy the benefits of a farther reaching, clearer wireless signal.
LUXUL WIRELESS PRODUCTS COVERED BY THIS GUIDE XWK1-24-FP14 - X-WAV 2.4GHz Outdoor Wi-Fi Range Extender Antenna Kit
