Transcript
10/L1, 493 Riversdale Road Camberwell VIC 3124 – Australia P: 1300 468 469 | E:
[email protected] | www.telecomtest.com.au
XG2128 E1 BER Tester Quick Start Manual
Front panel Tx(75 Ω) DC12V Input Jack
Tx/Rx(120 Ω)
Rx( 75 Ω) USB Port
LCD Display
LED Alarm and Status Indicators Functional Keyboard
2009-11-13
2
Side panel
DC12V Input Jack
USB Port
75 Ω (Rx) Unbalance Interface (L9)
2009-11-13
120 Ω Balance Interface (RJ45)
75 Ω (Tx) Unbalance Interface (L9)
3
Back panel
Disassembly-proof Label
Back Cover (put in battery)
Serial Number Label
2009-11-13
4
LED Indicators
2009-11-13
5
Functional Keyboard Soft keys
Setting, Result, Storage,
Page up, page down, left&up, right&down key
Other keys
Single Error insert key, Start/Stop key
2009-11-13
Backlight, Power key
6
Connect cables
75 ohm unbalance
Self-loop Test (L9)
2009-11-13
7
Connect cables
75 ohm unbalance
Connect to device (L9 or BNC)
Connect to device (L9 or BNC)
2009-11-13
8
Connect Cables
120 ohm balance
Connect to device (Clamps Red: Tx Yellow: Rx) RJ45
2009-11-13
9
Operate E1 BER Tester
Press SETTING key and F1, F2, F3, F4, page up, down, left&up, right&down keys to revise the settings according to practical use Revise the settings like mode, line code, interface, framing, polarity, test pattern, etc.
Press SETTING key and F1, F2, F3, F4 keys to revise settings according to the transmission line and the functions you require to test
2009-11-13
10
Operate E1 BER Tester
Press F1, F2, F3 to switch between these 3 modes
2009-11-13
11
Operate E1 BER Tester
Press right&down key to the position as below:
Press F1, F2 to switch between 75 Ω and 120 Ω
2009-11-13
12
Operate E1 BER Tester
Other settings in this page are revised in the same way as above, then press page down key:
This shows page 2. Please revise the settings accordingly
2009-11-13
13
Operate E1 BER Tester
Press page down key:
This shows page 3.
Please revise the settings accordingly
2009-11-13
14
Operate E1 BER Tester
After settings, press START key to begin the test.
Press START key to begin the test
2009-11-13
15
Operate E1 BER Tester
This shows the test is started. Please click RESULT key to view the test results.
No signal and shows in Yellow This LED lights up in green when starting test 2009-11-13
16
Operate E1 BER Tester
And then press RESULT key to view results
These LED indicators also show the results if there is something wrong with the transmission line Press RESULT key to view the test results
2009-11-13
17
Operate E1 BER Tester
Press F1, F2, F3, F4 key to view the results.
2009-11-13
18
Operate E1 BER Tester
Stop the test and save the records
Click F1 and store the record in the tester. You can input the record name and save the record.
2009-11-13
19
Operate E1 BER Tester
Press OTHER key and then F1,F2,F3,F4 key to switch to PC Communication
PC COMM
2009-11-13
20
Operate E1 BER Tester
In PC COMMUNICATION, set the USB port to ON state, upload the test records to PC
Set the USB Port to ON state, and then connect tester to PC to upload the records Press F1, F2 key to set ON or OFF
2009-11-13
21
Operate E1 BER Tester
Warning: In PC COMMUNICATATION, do not plug/unplug USB cable when the tester is on.
2009-11-13
22
View records on PC
2009-11-13
23
Print out records
2009-11-13
24
E1 BER Tester and accessories
2009-11-13
25
