. Xiaoyu163. Com Qq376315150 99 28 94 29 8

Transcript

http://www.xiaoyu163.com ZS-M35 892498299 376315150 QQSERVICE MANUAL AEP Model UK Model Ver 1.0 2000. 02 TEL TEL Model Name Using Similar Mechanism CD Section Optical Pick-up Name KSS-213C Model Name Using Similar Mechanism PMC-MD55 MD Mechanism Type MDM-5GA QQ 376315150 892498299 Base Unit Name MBU-5A Optical Pick-up Name KMS-260B SPECIFICATIONS CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 785 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of programme positions 2 Frequency response 20 - 20,000 Hz +1/–2 dB Wow and flutter Below measurable limit Radio section Frequency range FM: 87.5 - 108 MHz MW: 531 - 1,602 kHz LW: 153 - 279 kHz IF FM: 10.7 MHz MW/LW: 450 kHz Aerials FM: Telescopic aerial External aerial terminal MW/LW: External aerial terminals www . MD player section System Minidisc digital audio system Disc MiniDisc Laser diode properties Material: GaAlAs Wave length: 785 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Recording/playback time Stereo recording: Maximum 80 minutes (with MDW-80) Monaural recording: Maximum 160 minutes (with MDW-80) Revolutions 400 rpm to 900 rpm (CLV) Error correction Advanced Cross Interleave Reed Solomon Code (ACIRC) Sampling frequency 44.1 kHz – Continued on next page – xiaoy u163. com PERSONAL MINIDISC SYSTEM –1– http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 ZS-M50 KSM-213CDM QQ QQ MD Section CD Mechanism Type 13942296513 13942296513 U.S. and foreign patents licensed from Dolby Laboratories Licensing Corporation. http://www.xiaoyu163.com QQ 376315150 892498299 Coding Adaptive TRansform Acoustic Coding (ATRAC) Modulation system EFM (Eight-to-Fourteen Modulation) Number of programme positions 2 stereo programme positions Frequency response 20 - 20,000 Hz +1/–2 dB Signal-to-noise ratio Over 80 dB (during playback) Wow and flutter Below measurable limit www . xiaoy u163. com –2– http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 Design and specifications are subject to change without notice. QQ 376315150 892498299 QQ QQ TEL 13942296513 13942296513 13942296513 approx. 498.5 × 173.5 × 227 mm (w/h/d) (19 3/4 × 6 7/8 × 11 inches) Mass approx. 5.2 kg (11 lb. 7 oz) Supplied accessories Mains lead (1) Remote control (1) MW/LW loop aerial (1) TEL TEL General Speaker Full-range: 8 cm (3 in.) dia.,4 ohms, cone type (2) Inputs LINE IN (stereo minijack):Sensitivity 436 mV/ 870 mV Outputs Headphones jack (stereo minijack) (1): For 32 ohms impedance headphones Maximum power output 5W+5W Power requirements For personal minidisc system: 230 V AC, 50 Hz For back-up memory: 4.5 V DC, 3 R6 (size AA) batteries For remote control: 3 V DC, 2 R6 (size AA) batteries Power consumption 24 W Dimensions (incl.projecting parts) http://www.xiaoyu163.com QQ 376315150 892498299 TABLE OF CONTENTS 2. GENERAL TEL Playing a CD ....................................................................... 7 Recording a whole CD ........................................................ 7 Playing an MD ..................................................................... 8 Listening to the radio ........................................................... 8 13942296513 3. DISASSEMBLY QQ TEL 13942296513 QQ 376315150 892498299 7. EXPLODED VIEWS 7-1. 7-2. 7-3. 7-4. 7-5. 7-6. 7-7. Cabinet (Rear) Section .................................................... 103 Cabinet (Front) Section ................................................... 104 Cabinet (Upper) Section .................................................. 105 MD Block Section ........................................................... 106 MD Mechanism Section (MDM-5GA) .......................... 107 MD Base unit Section (MBU-5A) ................................. 108 Optical Pick-up Section (KSM-213CDM) ...................... 109 8. ELECTRICAL PARTS LIST .................................... 110 4. TEST MODE 4-1. MD section ........................................................................ 19 5. ELECTRICAL ADJUSTMENTS 5-1. Tuner section ..................................................................... 24 5-2. MD section ........................................................................ 26 5-3. CD section ......................................................................... 33 www . xiaoy u163. com –3– http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 3-1. Cabinet (Rear) Assy ............................................................ 9 3-2. Power Board ........................................................................ 9 3-3. Cabinet (Upper) Assy ........................................................ 10 3-4. MD Block Assy ................................................................. 10 3-5. Tuner Board ....................................................................... 11 3-6. Jack Board ......................................................................... 11 3-7. LED Board ........................................................................ 12 3-8. Key Board ......................................................................... 12 3-9. Top Board .......................................................................... 13 3-10. FL Board ........................................................................... 13 3-11. Main board ........................................................................ 14 3-12. CD Board .......................................................................... 14 3-13. CD Mechanism Block ....................................................... 15 3-14. DG Board .......................................................................... 15 3-15. Plate (Front), Shield .......................................................... 16 3-16. MD Mechanism Block-1 (MDM-5GA) ............................ 16 3-17. MD Mechanism Block-2 (Slider (Cam) Assy) ................. 17 3-18. MD Mechanism Block-3 (BD Board) ............................... 18 3-19. MD Mechanism Black-4 (SW Board) ............................... 18 QQ 6-1. IC Pin Function Descriptions ............................................ 35 6-2. Circuit Boards Location .................................................... 44 6-3. Block Diagram –Tuner Section– ....................................... 45 6-4. Block Diagram –MD Section– .......................................... 48 6-5. Block Diagram –CD Section– ........................................... 51 6-6. Block Diagram –Audio Section– ...................................... 53 6-7. Schematic Diagram –CD Section (1/2)– ........................... 55 6-8. Schematic Diagram –CD Section (2/2)– ........................... 57 6-9. Printed Wiring Boards –CD Section– ............................... 59 6-10. Printed Wiring Boards –Tuner Section– ........................... 61 6-11. Schematic Diagrams –Tuner Section– .............................. 63 6-12. Printed Wiring Boards –BD Section– ............................... 65 6-13. Schematic Diagram –BD Section (1/2)– ........................... 67 6-14. Schematic Diagrams –BD Section (2/2)– ......................... 69 6-15. Schematic Diagram –DG Section– ................................... 71 6-16. Schematic Diagram –DG Section– ................................... 73 6-17. Printed Wiring Board –DG Section– ................................. 75 6-18. Printed Wiring Board –Main Section– .............................. 77 6-19. Schematic Diagram –Main Section (1/3)– ........................ 79 6-20. Schematic Diagram –Main Section (2/3)– ........................ 81 6-21. Schematic Diagram –Main Section (3/3)– ........................ 83 6-22. Printed Wiring Boards –Panel Section– ............................ 85 6-23. Schematic Diagrams –Panel Section– ............................... 87 6-24. Printed Wiring Boards –Switch Section– .......................... 89 6-25. Schematic Diagrams –Switch Section– ............................ 91 6-26. Printed Wiring Boards –Power Supply Section– .............. 93 6-27. Schematic Diagrams –Power Supply Section– ................. 95 6-28. IC Block Diagrams ............................................................ 97 13942296513 6. DIAGRAMS 1-1. Notes on Handling the Optical Pick-up Block or Base Unit .. 4 1-2. Notes on Laser Diode Emission Check ............................... 4 1-3. Notes on Chip Component Replacement ............................ 4 1-4. Flexible Circuit Board Repairing ........................................ 4 1-5. Chuck Plate Jig on Repairing .............................................. 4 1-6. Demonstration ..................................................................... 4 1-7. Checking the Laser Diode and Focus Search Operation ..... 4 1-8. Jig for Checking BD Board Waveform ............................... 5 1-9. Checks Prior to Parts Replacement and Adjustments ......... 6 1-10. Change of Pulley ................................................................. 6 TEL 1. SERVICING NOTES http://www.xiaoyu163.com SECTION 1 SERVICING NOTES QQ 376315150 892498299 This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the bottom exterior. 1-5. CHUCK PLATE JIG ON REPAIRING On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. • Code number of Chuck Plate Jig: X-4918-255-1 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. 1-2. NOTES ON LASER DIODE EMISSION CHECK 1-3. NOTES ON CHIP COMPONENT REPLACEMENT • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. 1. Turn on the POWER and open the CD cover. 2. As shown below, push S402 (CD DOOR) with a screwdriver or other tool. 3. Press the CD button. 4. Check the objective lens to make sure that the laser diode is emitting light. If not so, the auto power control circuit or optical pickup would be damaged. Verify that the objective lens moves vertically three times for focus search. QQ 376315150 892498299 1-4. FLEXIBLE CIRCUIT BOARD REPAIRING • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! www xiaoy u163. com LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. . S402 –4– http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 1-7. CHECKING THE LASER DIODE AND FOCUS SEARCH OPERATION QQ QQ The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. This set enters the demonstration mode about 10 seconds after the power cord is connected. The demonstration displays such as “DEMONSTRATION MODE” and “CREATE YOUR ORIGINAL MD” then appears. When no operation is entered for one minute after the [OPERATE] button is turned on, the demonstration mode is also entered. To release the demonstration mode, set the timer in this set or press and hold down the [NO/CANCEL] button for about 2 seconds. 13942296513 13942296513 The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. 1-6. DEMONSTRATION TEL TEL 1-1. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT http://www.xiaoyu163.com QQ 376315150 892498299 1-8. JIG FOR CHECKING BD BOARD WAVEFORM The special jig (J-2501-149-A) is useful for checking the waveform of the BD board. The names of terminals and the checking items to be performed are shown as follows. GND : Ground I+3V : For measuring IOP (Check the deterioration of the optical pick-up laser) IOP : For measuring IOP (Check the deterioration of the optical pick-up laser) TEO : TRK error signal (Traverse adjustment) VC : Reference level for checking the signal RF : RF signal (Check jitter) Mechanism deck TEL TEL 13942296513 13942296513 CN110 5P connector RF VC TEO IOP I+3V GND RF VC 1 RF VC TEO for MDM-3 IOP 5 I+3V TEO www xiaoy u163. com IOP I+3V . GND –5– http://www.xiaoyu163.com 1 VC RF TEO for MDM-5 IOP I+3V 6 GND 376315150 892498299 376315150 892498299 QQ 376315150 892498299 TEL 13942296513 QQ QQ 6P connector http://www.xiaoyu163.com QQ 376315150 892498299 1-9. CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS (FOR MD SECTION) Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent. Details of the procedures are described in “5 Electrical Adjustments”. Criteria for Determination (Unsatisfactory if specified value is not satisfied) Measure if unsatisfactory: • Replace the optical pick-up Focus bias check (6-2 : See page 28) • Error rate check Specified value : For points a, b, and c C1 error : About 200 ADER : Below 2 • Replace the optical pick-up C PLAY check (6-3 : See page 28) • Error rate check Specified value: a. When using test disc (MDW-74/AU-1) C1 error : Below 80 ADER : Below 2 b. When using check disc (TDYS-1) C1 error : Below 50 • Replace the optical pick-up Self-recording/playback check (6-4 : See page 28) • CPLAY error rate check Specified value: C1 error : Below 80 ADER : Below 2 If always unsatisfactory: • Replace the overwrite head • Check for disconnection of the circuits around the overwrite head TEL 13942296513 QQ TEL 13942296513 Note: The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for adjustments. When performing adjustments, use the specified values for adjustments. 1-10. CHANGE OF PULLEY pulley M102, 103 2.5 mm Install the pulley to the motor. www . xiaoy u163. com –6– http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 If occasionally unsatisfactory: • Check if the overwrite head is distorted • Check the mechanism around the sled QQ lop (at 7mW) • Labeled on the optical pickup Iop value ± 10mA 13942296513 • Clean the optical pick-up • Adjust again • Replace the optical pick-up TEL • 0.9 mW power Specified value : 0.84 to 0.92 mW • 7.0 mW power Specified value : 6.8 to 7.2 mW Laser power check (6-1 : See page 28) http://www.xiaoyu163.com SECTION 2 GENERAL QQ 376315150 892498299 Playing a CD This section is extracted from instruction manual. Use these buttons for additional operations 1, 2 3 CD u CDx ., > Z PUSH OPEN/CLOSE VOLUME –, + OPERATE Tip Next time you want to listen to a CD, just press CD u . The player turns on automatically and starts playing the CD. For hookup instructions, see pages 64 - 67. 1 2 VOLUME +, – (VOL +, – on the remote) stop playback CD x pause playback CD u (CD X on the remote) Press the button again to resume play after pause. go to the next track > go back to the previous track . remove the CD Z PUSH OPEN/CLOSE turn on/off the player O P E R AT E Close the lid of the CD compartment. 3 Press CD u (CD N on the remote). Display Track number QQ 376315150 892498299 Playing time Recording a whole CD 4 (Synchronized recording) 4 5 3 To record at high speed, press HIGH SPEED. The indicator lights up. 1 2 To record at normal speed, skip this step. 5 Press SYNCHRO REC CD N MD. The player starts recording automatically. If the MD has any previous recording, recording will be made from the last recorded position. For hookup instructions, see pages 64 - 67. 1 Insert a recordable MD (direct power-on). With the label side up Display After “TOC Reading”is displayed,the disc name will be displayedif it is labelled. Insert in the direction of arrow 2 www 3 Press Z PUSH OPEN/CLOSE and place the CD on the CD compartment. . Press CD x . With the label side up Remaining recording time of MD Notes Use these buttons for additional operations • OPERATE After you stop recording, do not disconnectthe mains lead or move the player while “TOC EDIT” is flashingin the display. If you do so, recording may not be done properly. • When you record a whole CD, you cannot pause recording. Tips • Adjusting the volume or the audio emphasis (page 56) will not affect the recording level. Keep the volume at a moderate level so as to prevent the sound from skipping. • To record over the previous recording, see page 40. • Once the clock is set, the recording date and time are stamped automatically (page 57). • You can label an MD or a track during recording (page 51). CD x –7– http://www.xiaoyu163.com MD x MD YES ENTER NO CANCEL To Press stop recording MD x or CD x turn on/off the player O P E R AT E xiaoy u163. com Press Z PUSH OPEN/CLOSE again to close the CD compartment. Track number of MD If “CD>MD OK?” alternates with time display There is not enough space on the MD to record the whole CD. If it is all right to record as much as possible and cancel recording of some tracks, press YES•ENTER. To stop recording, press NO•CANCEL. If any other messages are displayed, see page 80. 376315150 892498299 376315150 892498299 TEL 13942296513 QQ QQ The player turns on (direct power-on) and the player plays all the tracks once. 13942296513 13942296513 With the label side up Press adjust the volume TEL TEL Press Z PUSH OPEN/CLOSE down to open the CD compartment and place the CD on the CD compartment. To http://www.xiaoyu163.com QQ 376315150 892498299 Playing an MD Use these buttons for additional operations 1 .. > 2 MD u MD x VOLUME –, + OPERATE Z Tip Next time you want to listen to a MD, just press MD u. The player turns on automatically and starts playing the For hookup instructions, see pages 64 - 67. 1 Display Insert the MD (direct power-on). VOLUME +, – (VOL +, – on the remote) stop playback MD x pause playback MD. MD u (MD X on the remote) Press the button again to resume play after pause. go to the next track > go back to the previous track . remove the MD Z turn on/off the player O P E R AT E Insert in the direction of the arrow 2 Press MD u (MD N on the remote). Track name is displayed The player plays all the tracks once. m Playingtime QQ 376315150 892498299 Listening to the radio Use these buttons for additional operations 2 OPERATE 1 VOLUME –, + MONO/ST REPEAT For hookup instructions, see pages 64 - 67. 1 Press RADIO BAND until the band you want appears in the display (direct power-on). Display “FM1”,“FM2”,“MW”or “LW”appears 2 Hold down TUNE + or TUNE – until the frequency digits begin to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. www Indicatesan FM stereo broadcast Tips • The “FM1” and “FM2” bands have the same functions. You can store the stations you want separately in “FM1” and “FM2” (page 22). • If the FM broadcast is noisy, press MONO/ ST•REPEAT (MODE on the remote) until “Mono” appears in the display and radio will play in monaural. • N ext time you want to listen to the radio, just press RADIO BAND. The player turns on automatically and starts playing the previous station. Press adjust the volume VOLUME +, – (VOL +, – on the remote) turn on/off the radio O P E R AT E To improve broadcast reception FM: Set the FM ANTENNA SELECTOR at the rear of the player to “ ” (telescopic aerial). Reorient the aerial for FM. xiaoy u163. com If you can’t tune in a station, press TUNE + or TUNE – repeatedly to change the frequency step by step. . To MW/LW: Keep the MW/LW loop aerial as far as possible from the player and reorient it. If the broadcast is still noisy, connect the external aerial (page 67). –8– http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 QQ QQ Track number 13942296513 13942296513 With the label side up Press adjust the volume TEL TEL After “TOC Reading”is displayed,the disc name will be displayedif it is labelled. To http://www.xiaoyu163.com SECTION 3 DISASSEMBLY QQ 376315150 892498299 Note : This set can be disassemble according to the following sequence. Set Cabinet (Rear) Assy Cabinet (Upper) Assy FL Board Power Board Top Board Main Board CD Mechanism Block CD Board MD Block Assy Tuner Board Jack Board DG Board LED Board Key Board Plate (Front), Shield MD Mechanism Block - 1 (MDM-5GA) MD Mechanism Block - 2 (Slider (Cam) Assy) MD Mechanism Block - 3 (BD Board) MD Mechanism Block - 4 (SW board) Note : Follow the disassembly procedure in the numerical order given. TEL TEL 3-1. CABINET (REAR) ASSY 7 CN401 1 BVTP 3x12 13942296513 13942296513 6 CN402 handle 8 cabinet (rear) assy 3 BVTP 3x14 5 BVTP 3x14 4 BVTP 3x12 3-2. POWER BOARD 1 BVTP 3x12 cabinet (rear) assy chassis, transformer 3 BVTP 4x12 www 5 xiaoy u163. com 4 BVTP 3x12 . 6 POWER board 2 CN903 –9– http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 2 BVTP 3x14 QQ QQ QQ 376315150 892498299 TEL 13942296513 http://www.xiaoyu163.com QQ 376315150 892498299 3-3. CABINET (UPPER) ASSY qacabinet (upper) assy 2 CN705 3 CN404 4 connector TEL TEL q; CN409 1 BVTP 3x10 8 CN407 7 CN303 6 CN408 3-4. MD BLOCK ASSY 3 MD block assy 2 BVTP 3x14 www xiaoy u163. com 1 CN2 . – 10 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 QQ QQ TEL 13942296513 5 CN301 13942296513 13942296513 9 CN406 http://www.xiaoyu163.com QQ 376315150 892498299 3-5. TUNER BOARD 1 BVTP 3x10 8 Remove the solders. 5 TUNER board 2 BVTP 3x10 6 BVTP 3x10 7 antenna SW board 3 BVTP 3x10 3-6. JACK BOARD 1 BVTP 2.6x8 www xiaoy u163. com 3 JACK board . 2 CN306 – 11 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 QQ QQ TEL 13942296513 13942296513 13942296513 4 BVTP 3x10 TEL TEL chassis (TU) http://www.xiaoyu163.com QQ 376315150 892498299 3-7. LED BOARD 3 LED board 3-8. KEY BOARD 1 BVTP 2.6x8 2 BVTP 2.6x8 www xiaoy u163. com 3 KEY board . – 12 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 QQ QQ TEL 13942296513 13942296513 13942296513 2 BVTP 2.6x8 TEL TEL 1 BVTP 2.6x8 http://www.xiaoyu163.com QQ 376315150 892498299 3-9. TOP BOARD 2 1 BVTP 2.6x8 TEL TEL 4 button (top) 3 BVTP 2.6x8 1 CN405 www 3 FL board xiaoy u163. com 2 BVTP 3x10 . – 13 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 3-10. FL BOARD QQ QQ QQ 376315150 892498299 TEL 13942296513 13942296513 13942296513 5 TOP board http://www.xiaoyu163.com QQ 376315150 892498299 3-11. MAIN BOARD 5 BVTP 3x10 1 CN410 4 BVTP 3x10 6 BVTP 3x10 8 MAIN board TEL TEL 7 CN403 13942296513 13942296513 2 CN707 3 CN704 3-12. CD BOARD 1 CN801 2 BVTP 3x10 3 BVTP 3x10 4 CN701 5 CD board www . xiaoy u163. com – 14 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 TEL 13942296513 QQ QQ CD board http://www.xiaoyu163.com QQ 376315150 892498299 3-13. CD MECHANISM BLOCK 1 PWH 2.6x10 2 PWH 2.6x10 3 4 CD mechanism block TEL TEL 13942296513 13942296513 1 P 2.6x5 2 plate (lower) , shield 5 CN605 6 CN603 4 P 2.6x5 7 3 P 2.6x5 q; DG board 8 CN602 www xiaoy u163. com 9 CN601 . claws – 15 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 3-14. DG BOARD QQ QQ QQ 376315150 892498299 TEL 13942296513 http://www.xiaoyu163.com QQ 376315150 892498299 3-15. PLATE (FRONT), SHIELD 3 plate (front), shield TEL TEL 13942296513 13942296513 2 P 2.6x5 1 P 2.6x5 3 claws 5 plate (upper), shield 4 claws 6 BVTTWH M3 7 BVTTWH M3 9 MD mechanism block (MDM-5GA) www xiaoy u163. com 8 harnes . 1 P 2.6x5 2 P 2.6x5 – 16 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 3-16. MD MECHANISM BLOCK-1 (MDM-5GA) QQ QQ QQ 376315150 892498299 TEL 13942296513 http://www.xiaoyu163.com QQ 376315150 892498299 3-17. MD MECHANISM BLOCK-2 (SLIDER (CAM) ASSY) 6 slider (cam) assy 3 bracket (guide L) 1 BV 2.6 (1T3B) TEL TEL 4 BV 2.6 (1T3B) 5 bracket (guide R) When assembling, set the press fitting shaft of the cam gear horizontal to the lever (head). press fitting shaft lever (head) cam gear A www When assembling, insert the shaft of the lever (O/C) with A part fit in the slot. . xiaoy u163. com – 17 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 horizontal QQ QQ QQ 376315150 892498299 TEL 13942296513 13942296513 13942296513 2 spring, leaf http://www.xiaoyu163.com QQ 376315150 892498299 3-18. MD MECHANISM BLOCK-3 (BD BOARD) 2 MD base unit 13942296513 13942296513 6 CN101 1 BV 2.6 (1T3B) 3 Removal the solders 4 M 1.7 3-19. MD MECHANISM BLOCK-4 (SW BOARD) 2 gear (B) 1 PTPWH M 2.6x6 3 PWH 1.7x4 4 motor assy, loading www xiaoy u163. com 6 SW board . 5 BTP 2.6x6 – 18 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 7 BD board QQ QQ TEL 13942296513 TEL TEL BD board (side A) 5 CN104 http://www.xiaoyu163.com SECTION 4 TEST MODE QQ 376315150 892498299 Refer to “5. ELECTRICAL ADJUSTMENT” for the test mode of CD section. 4-1. MD SECTION 1. PRECAUTIONS FOR USE OF TEST MODE • As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc is stopped before setting and removing it. Even if the Z (MD) button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc will not stop rotating. Therefore, it will be ejected while rotating. Be sure to press the Z (MD) button after pressing the [REC/REC MODE] button and the rotation of disc is stopped. 2. SETTING THE TEST MODE 3. RELEASING THE TEST MODE Hold down the [OPERATE] button and remove the power cord to reset the set. 4. BASIC OPERATIONS OF THE TEST MODE All operations are performed with the following buttons: u (MD), x (MD), [RADIO/BAND], and [REC/REC MODE]. The functions of these buttons are as follows. QQ 376315150 892498299 x (MD) Returns to the parameter/mode change. RADIO/BAND Goes ahead. Determines the setting/selection. REC/REC MODE Suspends. www . xiaoy u163. com – 19 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 Function Proceeds the parameter/mode change. QQ QQ Function name u (MD) 13942296513 13942296513 1. Set to standby state. 2. Press the buttons [SOUND] and [EDIT] and . (TUNE –) at the same time and then release them soon (within 100m sec). The TEST MODE is entered. TEL TEL 1-1. Recording laser emission mode and operating buttons • Continuous recording mode (CREC MODE) • Laser power check mode (LDPWR CHECK) • Laser power adjustment mode (LDPWR ADJUST) • When pressing the [REC] button. http://www.xiaoyu163.com QQ 376315150 892498299 5. SELECTING THE TEST MODE There are 9 types of test modes as shown below. The groups can be switched by press the u (MD) or x (MD) button. After selecting the group to be used, press the [RADIO/BAND] button. After setting a certain group, press the u (MD) or x (MD) button between these modes. Display TEMP ADJUST Contents Temperature compensation offset adjustment LDPWR ADJUST LDPWR CHECK EFBAL ADJUST Laser power adjustment Laser power check EF balance adjustment FBIAS ADJUST FBIAS CHECK CPLAY MODE Focus bias adjustment Focus bias check Continuous playback mode CREC MODE EEP MODE Continuous recording mode Non-volatile memory control xiaoy u163. com – 20 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 . QQ QQ www QQ 376315150 892498299 13942296513 13942296513 TEL 13942296513 TEL TEL • For details of each adjustment mode, refer to “5. Electrical Adjustments”. • If a different mode has been selected by mistake, press the [REC/REC MODE] button to release that mode. • EEP MODE is not used for servicing and therefore are not described in detail. If these modes are set accidentally, press the [REC/REC MODE] button to release the mode immediately. Be especially careful this mode will overwrite the non-volatile memory and reset it, and as a result, the unit will not operate normally. http://www.xiaoyu163.com QQ 376315150 892498299 5-1. Operating the Continuous Playback Mode 1. Entering the continuous playback mode (1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available) (2) Press the u (MD) or x (MD) button to display “CPLAY MODE”. (3) Press the [RADIO/BAND] button to change the display to “CPLAY MID”. AD = ”. (4) When access completes, the display changes to “C1 = Note: The numbers “ ” displayed show you error rates and ADER. 2. Changing the parts to be played back (1) Press the [RADIO/BAND] button during continuous playback to change the display as below. “CPLAY MID” t “CPLAY OUT” t “CPLAY IN” When pressed another time, the parts to be played back can be moved. When access completes, the display changes to “C1 = AD = ”. Note: The numbers “ ” displayed show you error rates and ADER. 3. Ending the continuous playback mode (1) Press the [REC/REC MODE] button. The display will change to “CPLAY MODE”. (2) Press the Z (MD) button and take out the disc. Note: The playback start addresses for IN, MID, and OUT are as follows. IN : 40h cluster MID : 300h cluster OUT : 700h cluster (2) 5-3. Non-Volatile Memory Mode (EEP MODE) This mode reads and writes the contents of the non-volatile memory. It is not used in servicing. If the unit entered this mode accidentally, press the [REC/REC MODE] button immediately to release it. www . xiaoy u163. com – 21 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 When pressed another time, the parts to be recorded can be changed. “[REC]” goes off. )” and “[REC] ” lights up. When access completes, the display changes to “CREC ( Note: The numbers “ ” displayed shows you the recording position addresses. 3. Ending the continuous recording mode (1) Press the [REC/REC MODE] button. The display changes to “CREC MODE” and “[REC] ” goes off. (2) Press the Z (MD) button and take out the disc. Note 1: The recording start addresses for IN, MID, and OUT are as follows. IN : 40h cluster MID : 300h cluster OUT : 700h cluster Note 2: The [REC/REC MODE] button can be used to stop recording anytime. Note 3: Do not perform continuous recording for long periods of time above 5 minutes. Note 4: During continuous recording, be careful not to apply vibration. (2) QQ QQ QQ 376315150 892498299 “CREC MID” t “CREC OUT” t “CREC IN” 13942296513 13942296513 TEL 13942296513 TEL TEL 5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check) 1. Entering the continuous recording mode (1) Set a recordable disc in the unit. (2) Press the u (MD) or x (MD) button to display “CREC MODE”. (3) Press the [RADIO/BAND] button to change the display to “CREC MID”. )” and “[REC] ” lights up. (4) When access completes, the display changes to “CREC ( Note: The numbers “ ” displayed shows you the recording position addresses. 2. Changing the parts to be recorded (1) When the [RADIO/BAND] button is pressed during continuous recording, the display changes as below. http://www.xiaoyu163.com QQ 376315150 892498299 6. FUNCTIONS OF OTHER BUTTONS Function Contents u (MD) and EDIT Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking servo turns ON/OFF. x (MD) and EDIT > . Stops continuous playback and continuous recording. The sled moves to the outer circumference only when this is pressed. The sled moves to the inner circumference only when this is pressed. REC/REC MODE and EDIT x (CD) and EDIT RADIO/BAND and EDIT LINE/LINE LEVEL When pressed during continuous playback, REC ON/OFF. Switches between the pit and groove modes when pressed. When pressed during continuous playback, switches the spindle servo mode (CLV-S y CLV-A). Switches the displayed contents each time the button is pressed Z (MD) OPERATE Ejects the disc Releases the test mode TEL TEL 7. TEST MODE DISPLAYS Each time the [LINE/LINE LEVEL] button is pressed, the display changes in the following order. Auto gain display (Not used in servicing) QQ QQ 13942296513 13942296513 Address display 1. Mode display Displays “TEMP ADJUST”, “CPLAYMODE”, etc. Mode display 2. Error rate display Displays the error rate in the following way. C1 = ssss AD = ss C1 = Indicates the C1 error. AD = Indicates ADER. Error rate display TEL 13942296513 QQ 376315150 892498299 IVR display (Not used in servicing) Note: “–” is displayed when servo is not imposed. 4. Auto gain display (Not used in servicing) The auto gain is displayed as follows. AG F = ss T = ss 5. IVR display (Not used in servicing) The IVR is displayed as follows. [ss][ss][ss] www . xiaoy u163. com – 22 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 3. Address display The address is displayed as follows. (MO: recordable disc, CD: playback only disc) Press the x (CD) and [EDIT] buttons at the same time to switches between the groove display and pit display. h = ssss s = ssss (MO pit and CD) h = ssss a = ssss (MO groove) h = Indicates the header address. s = Indicates the SUBQ address. a = Indicates the ADIP address. http://www.xiaoyu163.com QQ 376315150 892498299 MEANINGS OF OTHER DISPLAYS Contents Display SHUF PGM When Lit When Off [REC] During continuous playback (CLV: ON) Tracking servo OFF Recording mode ON STOP (CLV: OFF) Tracking servo ON Recording mode OFF TOC EDIT TRACK TIMER ABCD adjustment completed Pit CLV-S Groove CLV-A TEL TEL 13942296513 13942296513 . xiaoy u163. com – 23 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 www QQ 376315150 892498299 QQ QQ TEL 13942296513 http://www.xiaoyu163.com SECTION 5 ELECTRICAL ADJUSTMENTS QQ 376315150 892498299 5-1. TUNER SECTION 0 dB = 1 µV Precautions in Repairing Note : As a tuner unit (TU1) is difficult to repair if faulty, replace it with new one. • FM Section Setting: BAND button: FM FM FREQUENCY COVERAGE CHECK Frequency Display 87.5 MHz Reading on Digital voltmeter 1.4 Adjustment Part 108 MHz + 0.6 V – 0.4 V 6.9 + 1.1 V – 1.0 V FM TRACKING CHECK FM RF signal generator Adjust for a maximum reading on level meter. FM antenna (JW1,2) 0.01 µF 87.5 MHz 108 MHz set MW FREQUENCY COVERAGE ADJUSTMENT Frequency Display Reading on Digital voltmeter 1,611 kHz 1.0 ± 0.3 V 5.3 ± 0.3 V L5 CT4 Adjustment Part AM RF signal generator MW TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. Put the lead-wire antenna close to the supplied MW/LW loop aerial. 621 kHz 1,404 kHz 376315150 892498299 AM IF ADJUSTMENT Adjust for a maximum reading on level meter. T1 • Connecting Level Meter (FM, MW and LW) 450 kHz level meter (range: 0.5-5 V ac) LW FREQUENCY COVERAGE ADJUSTMENT 32 Ω set Frequency Display Reading on Digital voltmeter phones jack (J301) Adjustment Part • Connecting Digital Voltmeter (FM, MW and LW) 153 kHz 0.7 279 kHz + 0.5 V – 0.2 V 5.3 ± 0.2 V LW TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. digital voltmeter tuner board TP (VT) L4 CT1 162 kHz 261 kHz Adjustment Location: TUNER board (See page 25.) • Repeat the procedures in each adjustment several times, and the frequency coverage and tracking adjustments should be finally done by the trimmer capacitors. www . CT3 xiaoy u163. com – 24 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ TEL 13942296513 CT2 QQ QQ 30% amplitude modulation by 400 Hz signal output level : as low as possible L3 13942296513 13942296513 • MW/LW Section Setting: BAND button: MW or LW 531 kHz TEL TEL 22.5 kHz frequency deviation by 400 Hz signal output level : as low as possible http://www.xiaoyu163.com QQ 376315150 892498299 Adjustment Location: (COMPONENT SIDE) JW1 JW2 T1 AM IF ADJUSTMENT LW TRACKING ADJUSTMENT L4 CT1 QQ 376315150 892498299 L3 CT2 MW TRACKING ADJUSTMENT TP(VT) www . xiaoy u163. com – 25 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 QQ QQ CT3 LW FREQUENCY COVERAGE ADJUSTMENT 13942296513 13942296513 L5 MW FREQUENCY COVERAGE ADJUSTMENT TEL TEL CT4 http://www.xiaoyu163.com QQ 376315150 892498299 5-2. MD SECTION 1. PARTS REPLACEMENT AND ADJUSTMENT • Check and adjust the mechanism deck as follows. The procedure changes according to the part replaced. • Abbreviation OP : Optical pick-up OWH : Overwrite head • Laser power check • Focus bias check • C PLAY check • Self-recording/playback check OK Parts Replacement and Repair Has the OWH been replaced? YES NO QQ 376315150 892498299 NO YES Initial setting of the adjustment value Has OP or IC171 been replaced? NO YES IOP information recording (IOP value labeled on OP) Has IC171 or D101 been replaced? NO YES www xiaoy u163. com Temperature compensation offset adjustment . • Laser power adjustment • Traverse adjustment • Focus bias adjustment • Error rate adjustment • Focus bias check • Auto gain adjustment – 26 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 Has OP, IC171, IC101, or IC121 been replaced? QQ QQ TEL 13942296513 13942296513 13942296513 Check the sled and spindle mechanisms. Other causes can be suspected. TEL TEL NG http://www.xiaoyu163.com QQ 376315150 892498299 2. PRECAUTIONS FOR CHECKING LASER DIODE EMISSION To check the emission of the laser diode during adjustments, never view directly from the top as this may lose your eye-sight. 3. PRECAUTIONS FOR USE OF OPTICAL PICK-UP (KMS-260B) As the laser diode in the optical pick-up is easily damaged by static electricity, solder the laser tap of the flexible board when using it. Before disconnecting the connector, desolder first. Before connecting the connector, be careful not to remove the solder. Also take adequate measures to prevent damage by static electricity. Handle the flexible board with care as it breaks easily. pick-up flexible board 5. CREATING CONTINUOUSLY-RECORDED DISC 1. When replacing the following parts, perform the adjustments and checks with in the order shown in the following table. BD Board D101 QQ 376315150 892498299 IC101, IC121 IC192 1.Temperature compensation offset adjustment 2.Laser power adjustment The above has been how to create a continuous recorded data for the focus bias adjustment/check and MO error rate check. 3.EF balance adjustment Note: • Be careful not to apply vibration during continuous recording. 4.Focus bias adjustment 5.Error rate check 2. Set the test mode when performing adjustments. After completing the adjustments, release the test mode. Perform the adjustments and checks in “group S” of the test mode. 3. Perform the adjustments to be needed in the order shown. www . xiaoy u163. com – 27 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 Optical Pick-up IC171 * This disc is used in focus bias adjustment and error rate check. The following describes how to create a continuous recording disc. 1. Insert a disc (blank disc) commercially available. 2. Press the u (MD) or x (MD) button to display “CREC MODE”. 3. Press the [RADIO/BAND] button again to display “CREC MID”. Display “CREC (0300)” and start to recording. 4. Complete recording within 5 minutes. 5. Press the [REC/REC MODE] button and stop recording. 6. Press the Z (MD) button and remove the disc. QQ QQ 4. PRECAUTIONS FOR ADJUSTMENTS 13942296513 13942296513 Optical pick-up flexible board TEL TEL Laser Power Meter When performing laser power checks and adjustment (electrical adjustment), use of the new MD laser power meter 8010S (Part No. J-2501-145-A) instead of the conventional laser power meter is convenient. It sharply reduces the time and trouble to set the laser power meter sensor onto the objective lens of optical pick-up. laser tap TEL 13942296513 4. Use the following tools and measuring device. • Check Disc (MD) TDYS-1 (Part No. 4-963-646-01) • Test Disc (MDW-74/AU-1) (Part No. 8-892-341-41) • Laser power meter LPM-8001 (Part No. J-2501-046-A) or MD Laser power meter 8010S (Part No. J-2501-145-A) • Oscilloscope (Measure after performing CAL of prove) • Digital voltmeter • Thermometer • Jig for checking BD board waveform (Part No. : J-2501-149-A) 5. When observing several signals on the oscilloscope, etc., make sure that VC and ground do not connect inside the oscilloscope. (VC and ground will become short-circuited) 6. Using the above jig enables the waveform to be checked without the need to solder. (Refer to Servicing Notes on page 5) 7. As the disc used will affect the adjustment results, make sure that not dusts nor fingerprints are attached to it. http://www.xiaoyu163.com QQ 376315150 892498299 6. CHECK PRIOR TO REPAIRS These checks are performed before replacing parts according to “approximate specifications” to determine the faulty locations. For details, refer to “Checks Prior to Parts Replacement and Adjustments” (See page 6). 6-1. Laser Power Check Connection: laser power meter Optical pick-up objective lens BD board + – Specified Value: Laser power meter reading : 7.0 ± 0.2 mW Digital voltmeter reading : Value on the optical pick-up label ± 10 % (Optical pick-up label) KMS260B 27X40 B0825 lOP=82.5 mA in this case lOP (mA) = Digital voltmeter reading (mV)/1 (Ω) 5. Press the [REC/REC MODE] button to display “LDPWR CHECK” and stop the laser emission. (The [REC/REC MODE] button is effective at all times to stop the laser emission) Note 1: After step 4, each time the [RADIO/BAND] button is pressed, the display will be switched “LD 0.7 mW $ ”, “LD 6.2 mW $ ”, and “LD WP $ ”. Nothing needs to be performed here. ( = correction) www . MO Error Rate Check Checking Procedure: 1. Load the test disc (MDW-74/AU-1). 2. Press the u (MD) or x (MD) button to display “CPLAY MODE”. 3. Press the [RADIO/BAND] button to display “CPLAY MID”. 4. The display changes to “C1 = AD = ”. 5. If the C1 error rate is below 80, check that ADER is below 2. 6. Press the [REC/REC MODE] button to stop playback, then press the Z (MD) button and take out the test disc. QQ 376315150 892498299 CD Error Rate Check Checking Procedure: 1. Load the check disc (MD) TDYS-1. 2. Press the u (MD) or x (MD) button to display “CPLAY MODE”. 3. Press the [RADIO/BAND] button twice to display “CPLAY MID”. 4. The display changes to “C1 = AD = ”. 5. Check that the C1 error rate is below 50. 6. Press the [REC/REC MODE] button to stop playback, then press the Z (MD) button and take out the check disc. 6-4. Self-Recording/playback Check Prepare a continuous recording disc using the unit to be repaired and check the error rate. Checking Procedure: 1. Load a recordable disc (blank disc). 2. Press the u (MD) or x (MD) button to display “CREC MODE”. 3. Press the [RADIO/BAND] button to display “CREC MID”. 4. When recording starts, lights up “[REC]” and display “CREC @@@@” (@@@@ is the address). 5. About 1 minute later, press the [REC/REC MODE] button to stop continuous recording. 6. Turn the JOG dial to display “CPLAY MODE”. 7. Press the [RADIO/BAND] button to display “CPLAY MID”. 8. “C1 = AD = ” will be displayed. 9. Check that the C1 error becomes below 80 and the ADER below 2. 10. Press the [REC/REC MODE] button to stop play back, then press the Z (MD) button and take out the disc. xiaoy u163. com Note: After the TEST MODE is entered, insert the disc. – 28 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 6-3. C PLAY Check QQ QQ Checking Procedure: 1. Set the laser power meter on the objective lens of the optical pick-up. (When it cannot be set properly, press the . button or > button to move the optical pick-up) Connect the digital voltmeter to CN110 pin 5 (I+3 V) and CN110 pin 4 (IOP) on the BD board. 2. Press the u (MD) or x (MD) button to display “LDPWR CHECK”. 3. Press the [RADIO/BAND] button once to display “LD 0.9 mW $ ”. Check that the reading of the laser power meter become 0.84 to 0.92 mW. 4. Press the [RADIO/BAND] button once more to display “LD 7.0 mW $ ”. Check that the reading the laser power meter and digital voltmeter satisfy the specified value. 13942296513 13942296513 CN110 pin 5 (I +3V) CN110 pin 4 (IOP) TEL TEL digital voltmeter 6-2. Focus Bias Check Change the focus bias and check the focus tolerance amount. Checking Procedure: 1. Load the test disc (MDW-74/AU-1). 2. Press the u (MD) or x (MD) button to display “CPLAY MODE”. 3. Press the [RADIO/BAND] button twice to display “CPLAY MID”. AD = ” 4. Press the [REC/REC MODE] button when “C1 = is displayed. 5. Turn the JOG dial to display “FBIAS CHECK”. 6. Press the [RADIO/BAND] button to display “ / c = ”. The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [c =] indicate the focus bias value. Check that the C1 error is below 50 and ADER is below 2. 7. Press the [RADIO/BAND] button to display “ / b = ”. Check that the C1 error is about 200 and ADER is below 2. / a = ”. 8. Press the [RADIO/BAND] button to display “ Check that the C1 error is about 200 and ADER is below 2. 9. Press the [REC/REC MODE] button, then press the Z (MD) button and take out the test disc. http://www.xiaoyu163.com QQ 376315150 892498299 7. TEMPERATURE COMPENSATION OFFSET ADJUSTMENT Save the temperature data at that time in the non-volatile memory as 25 °C reference data. Note: 1. Usually, do not perform this adjustment. 2. Perform this adjustment in an ambient temperature of 22 °C to 28 °C. Perform it immediately after the power is turned on when the internal temperature of the unit is the same as the ambient temperature of 22 °C to 28 °C. 3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature. Connection: laser power meter lOP=82.5 mA in this case lOP (mA) = Digital voltmeter reading (mV)/1 (Ω) 10. Press the [REC/REC MODE] button to display “LDPWR CHECK” and stop the laser emission. (The [REC/REC MODE] button is effective at all times to stop the laser emission) Note 1: After step 9, each time the [RADIO/BAND] button is pressed, the display will be switched “LD 0.7 mW $ ”, “LD 6.2 mW $ ”, and “LD WP $ ”. Nothing needs to be performed here. ( = correction) QQ 376315150 892498299 Optical pick-up objective lens digital voltmeter BD board CN110 pin 5 (I +3V) CN110 pin 4 (IOP) + – Adjusting Procedure: 1. Set the laser power meter on the objective lens of the optical pick-up. (When it cannot be set properly, press the . button or > button to move the optical pick-up) Connect the digital voltmeter to CN110 pin 5 (I+3 V) and CN110 pin 4 (IOP) on the BD board. 2. Press the u (MD) or x (MD) button to display “LDPWR ADJUST”. (Laser power: For adjustment) 3. Press the [RADIO/BAND] button once to display “LD 0.9 mW $ ”. 4. Press the u (MD) or x (MD) button so that the reading of the laser power meter becomes 0.85 to 0.91 mW. Press the [RADIO/BAND] button after setting the range knob of the laser power meter, and save the adjustment results. (“LD SAVE $ ” will be displayed for a moment) 5. Then “LD 7.0 mW $ ” will be displayed. 6. Press the u (MD) or x (MD) button and adjust so that the reading on the laser power meter is 6.9 to 7.1 mV. Press the [RADIO/BAND] button to save the setting. www . xiaoy u163. com Note: Do not perform the emission with 7.0 mW more than 15 seconds continuously. – 29 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 KMS260B 27X40 B0825 QQ QQ 8. LASER POWER ADJUSTMENT (Optical pick-up label) 13942296513 13942296513 Specified Value: The “TEMP = ” should be within “E0 - EF”, “F0 - FF”, “00 0F”, “10 - 1F” and “20 - 2F”. Specified Value: Laser power meter reading : 7.0 ± 0.2 mW Digital voltmeter reading : Value on the optical pick-up label ± 10% TEL TEL Adjusting Procedure: 1. Press the u (MD) or x (MD) button to display “TEMP ADJUST”. 2. Press the [RADIO/BAND] button to select the “TEMP ADJUST” mode. 3. “TEMP = ” and the current temperature data will be displayed. 4. To save the data, press the [RADIO/BAND] button. When not saving the data, press the [REC/REC MODE] button. 5. When the [RADIO/BAND] button is pressed, “TEMP = SAVE” will be displayed and turned back to “TEMP ADJUST” display then. When the [REC/REC MODE] button is pressed, “TEMP ADJUST” will be displayed immediately. 7. Then, press the u (MD) or x (MD) to display “LDPWR CHECK”. 8. Press the [RADIO/BAND] button once to display “LD 0.9mW $ ”. Check that the reading of the laser power meter become 0.85 to 0.91 mW. 9. Press the [RADIO/BAND] button once more to display “LD 7.0 mW $ ”. Check that the reading the laser power meter and digital voltmeter satisfy the specified value. Note down the digital voltmeter reading value. http://www.xiaoyu163.com QQ 376315150 892498299 9. EF BALANCE ADJUSTMENT Note 1: Data will be erased during MO reading if a recorded disc is used in this adjustment. Note 2: If the traverse waveform is not clear, connect the oscilloscope as shown in the following figure so that it can be seen more clearly. oscilloscope (DC range) 8. Press the u (MD) or x (MD) button so that the waveform of the oscilloscope becomes the specified value. (When the JOG dial is turned, the of “EFB- ” changes and the waveform changes) In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible. (Write power traverse adjustment) Traverse Waveform BD board 330 k Ω CN110 pin 3 (TEO) + – CN110 pin 1 (VC) A VC 10 pF B Connection: Specification A = B oscilloscope (DC range) + – V: 0.1 V/div H: 10 ms/div Traverse Waveform A VC B Specification A = B 7. Press the [RADIO/BAND] button and save the result of adjustment to the non-volatile memory. (“EFB = SAVE” will be displayed for a moment. Then “EFB = MO-W” will be displayed) QQ 376315150 892498299 A VC B Specification A = B 12. Press the [RADIO/BAND] button, and save the adjustment results in the non-volatile memory. (“EFB = SABE” will be displayed for a moment) Next “EFBAL ADJUST” is displayed. The disc stops rotating automatically. 13. Press the Z (MD) button and take out the disc. 14. Load the check disc (MD) TDYS-1. 15. Press the [RADIO/BAND] button to display “EFB = CD”. Servo is imposed automatically. 16. Turn the JOG dial so that the waveform of the oscilloscope moves closer to the specified value. In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible. Traverse Waveform A VC B www xiaoy u163. com Specification A = B . – 30 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 Traverse Waveform QQ QQ Adjusting Procedure: 1. Connect an oscilloscope to CN110 pin 3 (TEO) and CN110 pin 1 (VC) on the BD board. 2. Load a disc (any available on the market). (Refer to Note 1) 3. Press the > button to move the optical pick-up outside the pit. 4. Press the u (MD) or x (MD) button to display “EFBAL ADJUST”. 5. Press the [RADIO/BAND] button to display “EFB = MO-R”. (Laser power READ power/Focus servo ON/tracking servo OFF/ spindle (S) servo ON) 6. Press the u (MD) or x (MD) button so that the waveform of the oscilloscope becomes the specified value. (When the u (MD) or x (MD) button is pressed, the of “EFB = ” changes and the waveform changes ) In this adjustment, waveform varies at intervals of approx. 2 %. Adjust the waveform so that the specified value is satisfied as much as possible. (Read power traverse adjustment) 13942296513 13942296513 CN110 pin 3 (TEO) CN110 pin 1 (VC) 9. Press the [RADIO/BAND] button, and save the adjustment results in the non-volatile memory. (“EFB = SAVE” will be displayed for a moment) MO-P” will be displayed. 10. “EFB = The optical pick-up moves to the pit area automatically and servo is imposed. 11. Press the u (MD) or x (MD) button until the waveform of the oscilloscope moves closer to the specified value. In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible. TEL TEL BD board http://www.xiaoyu163.com QQ 376315150 892498299 17. Press the [RADIO/BAND] button, display “EFB = SAVE” for a moment and save the adjustment results in the non-volatile memory. Next “EFBAL ADJUST” will be displayed. 18. Press the Z (MD) button and take out the disc. 10. FOCUS BIAS ADJUSTMENT Checking Procedure: 1. Load the continuously-recorded disc. (Refer to “5. CREATING CONTINUOUSLY-RECORDED DISC”) 2. Press the u (MD) or x (MD) button to display “CPLAY MODE”. 3. Press the [RADIO/BAND] button twice to display “CPLAY MID”. 4. Press the [REC/REC MODE] button when “C1 = AD = ” is displayed. 5. Press the u (MD) or x (MD) button to display “FBIAS CHECK”. 6. Press the [RADIO/BAND] button to display “ / c = ”. The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [c =] indicate the focus bias value. Check that the C1 error is below 50 and ADER is below 2. 7. Press the [RADIO/BAND] button and display “ / b = ”. Check that the C1 error is about 200 and ADER is below 2. / a = ”. 8. Press the [RADIO/BAND] button and display “ Check that the C1 error is about 200 and ADER is below 2. 9. Press the [REC/REC MODE] button, then press the Z (MD) button and take out the disc. A Focus bias value (F. BIAS) Note 1: If the C1 error and ADER are above other than the specified value at points A (step 8. in the above) or B (step 7. in the above), the focus bias adjustment may not have been carried out properly. Adjust perform the beginning again. xiaoy u163. com – 31 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 about 200 . Change the focus bias and check the focus tolerance amount. QQ QQ C1 error www 12. FOCUS BIAS CHECK 13942296513 13942296513 Note 1: The relation between the C1 error and focus bias is as shown in the following figure. Find points A and B in the following figure using the above adjustment. The focal point position C is automatically calculated form points A and B. Note 2: As the C1 error rate changes, perform the adjustment using the average value. C 11-2. MO Error Rate Check Checking Procedure: 1. Load the continuously-recorded disc. (Refer to “5. CREATING CONTINUOUSLY-RECORDED DISC”) 2. Press the u (MD) or x (MD) button to display “CPLAY MODE”. 3. Press the [RADIO/BAND] button to display “CPLAY MID”. = AD = ”. 4. The display changes to “C1 5. If the C1 error rate is below 50, check that ADER is 00. 6. Press the [REC/REC MODE] button to stop playback, then press the Z (MD) button and take out the test disc. QQ 376315150 892498299 TEL 13942296513 B 11-1. CD Error Rate Check Checking Procedure: 1. Load the check disc (MD) TDYS-1. 2. Press the u (MD) or x (MD) button and display “CPLAY MODE”. 3. Press the [RADIO/BAND] button twice and display “CPLAY MID”. = AD = ”. 4. The display changes to “C1 5. Check that the C1 error rate is below 20. 6. Press the [REC/REC MODE] button to stop playback, then press the Z (MD) button and take out the check disc. TEL TEL Adjusting Procedure: 1. Load the continuously-recorded disc. (Refer to “5. CREATING CONTINUOUSLY-RECORDED DISC”) 2. Press the u (MD) or x (MD) button to display “CPLAY MODE”. 3. Press the [RADIO/BAND] button to display “CPLAY MID”. = AD = ” 4. Press the [REC/REC MODE] button when “C1 is displayed. 5. Press the u (MD) or x (MD) button to display “FBIAS ADJUST”. 6. Press the [RADIO/BAND] button to display “ / a = ”. The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [a =] indicate the focus bias value. 7. Turn the JOG dial clockwise and find the focus bias value at which the C1 error rate becomes about 200 (Refer to Note 2). / b = ”. 8. Press the [RADIO/BAND] button to display “ 9. Press the u (MD) or x (MD) button counterclockwise and find the focus bias value at which the C1 error rate becomes about 200. 10. Press the [RADIO/BAND] button to display “ / c = ”. 11. Check that the C1 error rate is below 50 and ADER is 00. Then press the [RADIO/BAND] button. ( )” is above 20, press the 12. If the “( )” in “ [RADIO/BAND] button. If below 20, press the [REC/REC MODE] button and repeat the adjustment from step 2. 13. Press the Z (MD) button and take out the disc. 11. ERROR RATE CHECK http://www.xiaoyu163.com QQ 376315150 892498299 Adjustment Location: – BD BOARD (COMPONENT SIDE) – CN101 D101 GND I+3V IOP CN110 TEL TEL TEO RF VC NOTE 13942296513 13942296513 IC171 IC121 IC192 www xiaoy u163. com Note: It is useful to use the jig for checking the waveform. (Refer to Servicing Notes on page 5) . – 32 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 IC101 QQ QQ QQ 376315150 892498299 TEL 13942296513 – BD BOARD (CONDUCTOR SIDE) – http://www.xiaoyu163.com QQ 376315150 892498299 5-3. CD SECTION Display Set the CD test mode when performing confirmations. After completing the confirmation, release the CD test mode. 88 In the CD test mode, the set works as following sequence. XX XX XXX CD test mode sequence: 1. Enter the CD test mode (STOP mode 1) 2. STOP Mode 2 1. Press the x (CD) button to enter the STOP mode 2, and display as below. Display Press the x (CD) button. 2. STOP mode 2 07 00 3A0 2. Press the > and . button to move the optical pick-up to position of the track where signal is recorded. 3. FOCUS mode Press the [u, CD] button. 3. FOCUS Mode (Traverse Confirmation) 4. ALL SERVO ON mode 2 Press the x (CD) button. 00 3A0 QQ 376315150 892498299 Press the [u, CD] button. 6. TRACKING GAIN UP mode 2 07 Press the x (CD) button. 2. Connect an oscilloscope to TP (TEO) and TP (VC) on the CD board. Connection: oscilloscope (DC range) Press the [u, CD] button. CD board 7. ALL SERVO ON mode1 Press the x (CD) button. TP (TEO) TP (VC) + – 3. Confirm that the traverse level of waveform satisfy specified value as follows. Press the [u , CD] button. Traverse Waveform Note 1: ALL SERVO ON mode 1 and TRACKING GAIN UP mode 1: LPC ON (lights up “ALL” indication) ALL SERVO ON mode 2 and TRACKING GAIN UP mode 2: LPC OFF (Does not lights up “ALL” indication) *) LPC: Laser power control Note 2: TRACKING GAIN UP mode 1, 2 is not used in servicing. 1. Entering the CD Test Mode Press the [OPERATE] button to turn the power ON. Open the disc lid, and put a disc. Close the disc lid. Press the [OPERATE] button to standby state. Press the button [EDIT], [SOUND] and > (CD) simultaneously. 6. After display “CD” for a few seconds, enter the CD test mode (STOP mode 1), and display as below. 1. 2. 3. 4. 5. www . A VC B A=B Specified Value: traverse level: 160 to 380 mVp-p xiaoy u163. com Connecting Location: CD board (See page 34) – 33 – http://www.xiaoyu163.com traverse level: 160 to 380 mVp-p 376315150 892498299 376315150 892498299 TEL 13942296513 11 QQ QQ Press the [u, CD] button. 5. TRACKING GAIN UP mode 1 1. Press the u button to enter the FOCUS mode and display as below. (Focus servo ON. CLV-S, tacking and sled servo OFF) Display Press the x (CD) button. 13942296513 13942296513 Press the x (CD) button. TEL TEL 88 Press the [u, CD] button. http://www.xiaoyu163.com QQ 376315150 892498299 4. ALL SERVO ON Mode 1 6. Releasing the CD Test Mode (RF Level and Jitter Confirmation 1) 1. Press the u button four times to enter the ALL SERVO ON mode 1 (start playback the disc) and display as below. (All servo ON. LPC ON) Display 1. Press the x (CD) button to stop rotate the disc. 2. Press the [OPERATE] button to release the CD test mode and turn to standby state. Connecting Location: ALL 21 07 CD BOARD (CONDUCTOR SIDE) 00 3A0 2. Connect an oscilloscope to TP (RFO) and TP (VC) on the CD board. TEL TEL Connection: oscilloscope (DC range) TP(VC) TP (RFO) TP (VC) + – TP(TEO) TP(RFO) 3. Confirm that the RF level and jitter of waveform satisfy specified values as follows. RF signal Waveform RF level: 1.0 to 1.4 Vp-p QQ 376315150 892498299 Specified Values: RF level : 1.0 to 1.4 Vp-p jitter : less than 9 nsec Connecting Location: CD board 5. ALL SERVO ON Mode 2 (RF Level and Jitter Confirmation 2) 1. Press the u button to enter the LPC OFF mode and display as below. (All servo ON. LPC OFF) Display 21 07 00 3A0 2. Confirm that the RF level and jitter of waveform satisfy specified values as follows. www Specified Values: RF level : 0.8 to 1.4 Vp-p jitter : less than 9 nsec . xiaoy u163. com If the RF level and jitter are out of specified values, measure again after clean the object lens by an applicator with lens cleaning liquid. – 34 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 QQ QQ VOLT/DIV: 200 mV TIME/DIV: 500 ns 13942296513 13942296513 CD board http://www.xiaoyu163.com SECTION 6 DIAGRAMS QQ 376315150 892498299 6-1. IC PIN FUNCTION DESCRIPTIONS • BC BOARD IC101 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP) Pin No. 1 Pin Name I I/O I Pin Description I-V converted RF signal I input from the optical pick-up block detector 2 J I I-V converted RF signal J input from the optical pick-up block detector 3 VC O Middle point voltage (+ 1.65 V) generation output terminal 4–9 A–F I Signal input from the optical pick-up detector 10 PD I Light amount monitor input from the optical pick-up block laser diode 11 APC O Laser amplifier output terminal to the automatic power control circuit 12 APCREF I 13 GND — Reference voltage input terminal for setting laser power Ground terminal TEMPI I Connected to the temperature sensor 15 TEMPR O Output terminal for a temperature sensor reference voltage 16 SWDT I Writing serial data input from the CXD2654R (IC121) 17 SCLK I Serial data transfer clock signal input from the CXD2654R (IC121) Serial data latch pulse signal input from the CXD2654R (IC121) I Standby signal input terminal 20 F0CNT I 21 VREF O Reference voltage output terminal 22 EQADJ I Center frequency setting terminal for the internal circuit (EQ) 23 3TADJ I 24 VCC — 25 WBLADJ I Center frequency setting terminal for the internal circuit (BPF22) 26 TE O Tracking error signal output to the CXD2654R (IC121) 27 CSLED I Connected to the external capacitor for low-pass filter of the sled error signal 28 SE O Sled error signal output to the CXD2654R (IC121) 29 ADFM O FM signal output of the ADIP 30 ADIN I Receives a ADIP FM signal in AC coupling 31 ADAGC I Connected to the external capacitor for ADIP AGC 32 ADFG O ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2654R (IC121) 33 AUX O Auxiliary signal (I3 signal/temperature signal) output to the CXD2654R (IC121) 34 FE O Focus error signal output to the CXD2654R (IC121) “L”: standby (fixed at “H” in this set) Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input from the CXD2654R (IC121) Not used (open) Center frequency setting terminal for the internal circuit (BPF3T) Power supply terminal (+3.3V) TEL 13942296513 QQ 376315150 892498299 35 ABCD O Light amount signal (ABCD) output to the CXD2654R (IC121) 36 BOTM O Light amount signal (RF/ABCD) bottom hold output to the CXD264R (IC121) 37 PEAK O Light amount signal (RF/ABCD) peak hold output to the CXD2654R (IC121) 38 RF O Playback EFM RF signal output to the CXD2654R (IC121) 39 RFAGC I Connected to the external capacitor for RF auto gain control circuit 40 AGCI I Receives a RF signal in AC coupling 41 COMPO O User comparator output terminal 42 COMPP I User comparator input terminal 43 ADDC I Connected to the external capacitor for cutting the low band of the ADIP amplifier 44 OPO O User operational amplifier output terminal 45 OPN I User operational amplifier inversion input terminal 46 RFO O RF signal output terminal Not used (open) Not used (fixed at “L”) 47 MORFI I Receives a MO RF signal in AC coupling 48 MORFO O MO RF signal output terminal www . Not used (open) Not used (fixed at “L”) xiaoy u163. com – 35 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 I XSTBY QQ QQ XLAT 19 13942296513 13942296513 18 TEL TEL 14 http://www.xiaoyu163.com QQ 376315150 892498299 • BD BOARD IC121 CXD2654R (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER) Pin No. Pin Name I/O Pin Description Focus OK signal output to the MD mechanism controller (IC601) 1 MNT0 (FOK) O 2 MNT1 (SHOCK) O 3 MNT2 (XBUSY) O Busy monitor signal output to the MD mechanism controller (IC601) 4 MNT3 (SLOCK) O Spindle servo lock status monitor signal output to the MD mechanism controller (IC601) 5 SWDT I Writing serial data signal input from the MD mechanism controller (IC601) 6 SCLK I (S) 7 XLAT I (S) Serial data latch pulse signal input from the MD mechanism controller (IC601) 8 SRDT O (3) Reading serial data signal output to the MD mechanism controller (IC601) “H” is output when focus is on (“L”: NG) Track jump detection signal output to the MD mechanism controller (IC601) Serial data transfer clock signal input from the MD mechanism controller (IC601) Internal status (SENSE) output to the MD mechanism controller (IC601) I (S) Reset signal input from the MD mechanism controller (IC601) 11 SQSY O 12 DQSY O 13 RECP I 14 XINT O 15 TX I Subcode Q sync (SCOR) output to the MD mechanism controller (IC601) “L” is output every 13.3 msec “L” is output every 13.3 msec I 17 OSCO O Almost all, “H” is output Laser power selection signal input from the MD mechanism controller (IC601) “L”: playback mode, “H”: recording mode Interrupt status output to the MD mechanism controller (IC601) Recording data output enable signal input from the MD mechanism controller (IC601) Writing data transmission timing input (Also serves as the magnetic head on/off output) QQ 376315150 892498299 System clock signal (512 Fs = 22.5792 MHz) input terminal System clock signal (512 Fs = 22.5792 MHz) output terminal Not used (open) Input terminal for the system clock frequency setting 18 XTSL I 19 DIN0 I Digital audio signal input terminal when recording mode (for digital optical input) 20 DIN1 I Digital audio signal input terminal when recording mode (for digital optical input) 21 DOUT O 22 DATAI I Serial data input terminal 23 LRCKI I L/R sampling clock signal (44.1 kHz) input terminal 24 XBCKI I Bit clock signal (2.8224 MHz) input terminal 25 ADDT I Recording data input from the A/D, D/A converter (IC603) 26 DADT O Playback data output to the A/D, D/A converter (IC603) 27 LRCK O L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC603) 28 XBCK O Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC603) “L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set) Digital audio signal output terminal when playback mode (for digital optical output) Not used Not used (fixed at “L”) 29 FS256 O Clock signal (11.2896 MHz) output terminal 30 DVDD — Power supply terminal (+3.3 V) (digital system) 31 – 34 A03 – A00 O Address signal output to the D-RAM (IC124) 35 A10 O Address signal output to the external D-RAM 36 – 40 A04 – A08 O Address signal output to the D-RAM (IC124) 41 A11 O Address signal output to the external D-RAM 42 DVSS — www 43 XOE 44 XCAS 45 A09 . Not used (fixed at “L”) Not used (fixed at “L”) Not used (open) Not used (open) Not used (open) Ground terminal (digital system) xiaoy u163. com O Output enable signal output to the D-RAM (IC124) O Column address strobe signal output to the D-RAM (IC124) O Address signal output to the D-RAM (IC124) – 36 – http://www.xiaoyu163.com “L” active “L” active Not used 376315150 892498299 376315150 892498299 OSCI Almost all, “H” is output Digital In U-bit CD format subcode Q sync (SCOR) output to the MD mechanism controller (IC601) TEL 13942296513 16 “L”: reset QQ QQ O (3) 13942296513 13942296513 SENS XRST TEL TEL 9 10 http://www.xiaoyu163.com QQ 376315150 892498299 Pin No. 46 Pin Name XRAS I/O O 47 XWE O 48 D1 I/O 49 D0 I/O 50 D2 I/O Pin Description Row address strobe signal output to the D-RAM (IC124) Write enable signal output to the D-RAM (IC124) “L” active “L” active Two-way data bus with the D-RAM (IC124) 53 ASYO O 54 ASYI I (A) 55 AVDD — 56 BIAS I (A) Playback EFM asymmetry circuit constant current input terminal 57 RFI I (A) Playback EFM RF signal input from the CXA2523AR (IC101) 58 AVSS — 59 PCO O (3) Phase comparison output for master clock of the recording/playback EFM master PLL 60 FILI I (A) Filter input for master clock of the recording/playback master PLL 61 FILO O (A) Filter output for master clock of the recording/playback master PLL 62 CLTV I (A) Internal VCO control voltage input of the recording/playback master PLL 63 PEAK I (A) Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC101) 64 BOTM I (A) Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC101) 65 ABCD I (A) Light amount signal (ABCD) input form the CXA2523AR (IC101) 66 FE I (A) Focus error signal input from the CXA2523AR (IC101) 67 AUX1 I (A) Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC101) 68 VC I (A) Middle point voltage (+1.65 V) input from the CXA2523AR (IC101) 69 ADIO O (A) Monitor output of the A/D converter input signal 70 AVDD — Power supply terminal (+3.3 V) (analog system) Digital in PLL oscillation input from the external VCO Not used (fixed at “L”) Playback EFM full-swing output terminal Playback EFM asymmetry comparator voltage input terminal Power supply terminal (+3.3 V) (analog system) Ground terminal (analog system) QQ 376315150 892498299 TEL 13942296513 Not used (open) 71 ADRT I (A) A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set) 72 ADRB I (A) A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set) 73 AVSS — 74 SE I (A) Sled error signal input from the CXA2523AR (IC101) Ground terminal (analog system) 75 TE I (A) Tracking error signal input from the CXA2523AR (IC101) 76 DCHG I (A) Connected to the +3.3 V power supply 77 APC I (A) Error signal input for the laser automatic power control 78 ADFG I (S) ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC101) 79 F0CNT O Filter f0 control signal output to the CXA2523AR (IC101) 80 XLRF O Serial data latch pulse signal output to the CXA2523AR (IC101) 81 CKRF O Serial data transfer clock signal output to the CXA2523AR (IC101) 82 DTRF O Writing serial data output to the CXA2523AR (IC101) 83 APCREF O 84 LDDR O PWM signal output for the laser automatic power control 85 TRDR O Tracking servo drive PWM signal (–) output to the BH6511FS (IC152) Not used (fixed at “H”) Control signal output to the reference voltage generator circuit for the laser automatic power control Not used (open) 86 TFDR O Tracking servo drive PWM signal (+) output to the BH6511FS (IC152) 87 DVDD — Power supply terminal (+3.3 V) (digital system) 88 FFDR O Focus servo drive PWM signal (+) output to the BH6511FS (IC152) 89 FRDR O Focus servo drive PWM signal (–) output to the BH6511FS (IC152) 90 FS4 O Clock signal (176.4 kHz) output terminal (X’tal system) www . xiaoy u163. com – 37 – http://www.xiaoyu163.com Not used (open) 376315150 892498299 376315150 892498299 I (S) QQ QQ I/O MVCI 13942296513 13942296513 D3 52 TEL TEL 51 http://www.xiaoyu163.com QQ 376315150 892498299 Pin No. 91 Pin Name SRDR I/O O Pin Description Sled servo drive PWM signal (–) output to the BH6511FS (IC152) 92 SFDR O Sled servo drive PWM signal (+) output to the BH6511FS (IC152) 93 SPRD O Spindle servo drive PWM signal (–) output to the BH6511FS (IC152) Spindle servo drive PWM signal (+) output to the BH6511FS (IC152) 94 SPFD O 95 FGIN I (S) 96 TEST1 I 97 TEST2 I 98 TEST3 I 99 DVSS — Ground terminal (digital system) 100 EFMO O EFM signal output terminal when recording mode Input terminal for the test (fixed at “L”) * I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O. TEL TEL 13942296513 13942296513 . xiaoy u163. com – 38 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 www QQ 376315150 892498299 QQ QQ TEL 13942296513 http://www.xiaoyu163.com QQ 376315150 892498299 • IC401 CXP740096-043Q (SYSTEM CONTROL) Pin No. 1 Pin Name NC I/O — Pin Description 2 MEGA BASS O MEGA BASS on/off control signal output 3 LINE-LEVEL O Line in level control signal output 4 AU-CS O Chip select signal output to the electrical volume (IC301) 5 AU-DATA O Serial data output to the electrical volume (IC301) 6 AU-CLK O Serial data transfer clock signal output to the electrical volume (IC301) 7 RDS-DATA I 8 NC — Not used “L”: MEGA BASS on “L”: normal, “H”: high RDS serial data input from the RDS decoder Used for the AEP, UK models Not used I RDS serial data transfer clock signal input from the RDS decoder O Muting on/off control signal output for the tuner signal Used for the AEP, UK models 11 TU-CE O PLL serial chip enable signal output to the tuner PLL IC (IC2) 12 TU-DATA O PLL serial data output to the tuner PLL IC (IC2) 13 TU-CLK O PLL serial data transfer clock signal output to the tuner PLL IC (IC2) 14 TU-COUNT I PLL serial data input from the tuner PLL IC (IC2) 15 CD-DOOR I Detection signal input from the CD lid open/close detect switch (S402) 16 NC — “L”: muting on Not used I Key input terminal (A/D input) LED-CHARA-KAN O LED (LED board D609) on/off drive signal output 23 LED-123 O LED (LED board D610-613) on/off drive signal output 24 LED-456 O LED (LED board D607,615-617) on/off drive signal output 25 LED-789 O LED (LED board D618-621) on/off drive signal output 26 LED-0 O LED (LED board D622-625) on/off drive signal output 27 LED-CHARA-ABC O LED (LED board D608) on/off drive signal output 28 NC — Not used 29 LED-CLOCK O LED (LED board D602-614) on/off drive signal output 30 LED-HISPEED O LED (LED board D601) on/off drive signal output 31 RA-POWER O RA7V power supply on/off control signal output 32 NC — Not used 33 FL-CTR O FL-BU3.3V power supply on/off control signal output 34 PA-STANDBY O Power amplifier on/off control signal output 35 LINE-MUTE O LINE input muting on/off control signal output 36 KEY-C2 O Not used 37 KEY-C1 O Not used 38 FL-DIM O Control signal output for the brightness of fluorescent tube display 39 TU-SFT O Frequency shift of the main system clock control terminal 40 RST I System reset signal input from the reset signal generator (IC403) 41 VSS — 42 XTAL I TEL 13942296513 QQ 376315150 892498299 “L”: power on L: standby, H: power on “L”: reset Ground terminal Main system clock input terminal (8 MHz) 43 EXTAL O Main system clock input terminal (8 MHz) 44 FL-RST O Reset signal output to the fluorescent tube display drive IC (IC601) 45 FL-CS O Chip enable signal output to the fluorescent tube display drive IC (IC601) 46 FL-DATA O Serial data output to the fluorescent tube display drive IC (IC601) Serial data transfer clock signal output to the fluorescent tube display drive IC (IC601) 47 FL-CLK O 48 SELECT-GND I/O 49 SELECT I 50 NC — www . Destination setting terminal Fixed at “H” in this set xiaoy u163. com Destination setting terminal Not used – 39 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 KEY S4 – S0 22 QQ QQ 17 – 21 13942296513 13942296513 RDS-CLK TU-MUTE TEL TEL 9 10 http://www.xiaoyu163.com QQ 376315150 892498299 Pin No. 51 Pin Name KEY-C4A I/O I Key input terminal (A/D input) Pin Description 52 AVSS — Ground terminal (for A/D converter) 53 AVREF — Reference voltage (+3.3V) input terminal (for A/D converter) 54 AVDD — Power supply terminal (+3.3V) (for A/D converter) 55 – 58 KEY C3A – C0A I Key input terminal (A/D input) 59 3.3V-SHORT I AU 7.5V short test pin 60 – 62 KEY AD2 – AD0 I Key input terminal (A/D input) (TOP board) 63 MD-PDOWN O 64 MD-SRTS O System controller busy status monitor output to the MD mechanism controller (IC601) 65 MD-SCTS I MD mechanism controller busy status monitor input from the MD mechanism controller (IC601) MD-RST O Power down signal output to the MD mechanism controller (IC601) “L”: remove the AC power cord O MD play control signal output to the A/D, D/A converter (IC603) 13942296513 REC-H O MD REC control signal output to the A/D, D/A converter (IC603) “L”: MD recording mode 69 MD-SRXD O UART communication data input from the MD mechanism controller (IC601) 70 MD-STXD I UART communication data output to the MD mechanism controller (IC601) 71, 72 NC — Not used 73 CD-12/8 O Servo setting when CD operates faster. 74 CD-HISPEED O CD higher speed setting 75 CD-POWER O CD servo system power supply on/off control signal output 76 CD-MUTE O Muting on/off control signal output for the CD playback signal 77 NC — Not used 78 CD-CSOR I Subcode sync (S0+S1) detection signal input from the CD DSP IC (IC702) 79 CD-SQSO I Subcode Q data input from the CD DSP IC (IC702) 80 CD-XRST O Reset signal output to the CD RF AMP (IC701), CD DSP IC (IC702) 81 CD-SQCK O Subcode Q data reading clock signal output to the CD DSP IC (IC702) 82 CD-SENSE1 I Internal status (SENSE) input from the CD DSP IC (IC702) 83 CD-DATA O Serial data output to the CD DSP IC (IC702) 84 CD-XLAT O Serial data latch pulse signal output to the CD DSP IC (IC702) 85 RMC I Sircs remote control signal input from the remote control receiver (IC602) 86 TEX O Sub system clock output terminal (32.768 kHz) 87 TX I Sub system clock input terminal (32.768 kHz) 88 VSS — Ground terminal 89 VDD — Power supply terminal (+3.3V) 90 NC — Not used 91 CD-CLK O Serial data transfer clock signal output to the CD DSP IC (IC702) 92 CD-SENSE2 I Internal status (SENSE) input from the CD DSP IC (IC702) 93 CD-FOK I Focus OK signal input terminal 94 STBY-CTR O Power saving mode selection 95 ACCHK I AC power supply detection signal input 96 NC — Not used 97 PCON O Power on/off control signal output 98 AMUTE O Audio muting on/off control signal output 99 TU-LED I Input the signal for band tuning check from the tuner IC. 100 NC “L”: muting on “L”: AC in “L”: standby mode, “H”: power on “H”: muting on Not used – 40 – http://www.xiaoyu163.com 376315150 892498299 “H”: normal, “L”: Power saving mode QQ 376315150 892498299 Not used (open) xiaoy u163. com — . “L”: power on QQ 376315150 892498299 TEL 13942296513 www “L”: MD playback mode 13942296513 MD-H 68 ”H”: power on TEL 67 QQ TEL Power supply on/off control signal output for the MD mechanism controller (IC601) 66 http://www.xiaoyu163.com QQ 376315150 892498299 • DG BOARD IC601 RU8X13MF-0102 (MD MECHANISM CONTROLLER) Pin No. 1, 2 Pin Name DAOUT0, DAOUT1 I/O O 3–5 KEY0 – KEY2 I 6 CHACK-IN I 7 PACK-IN I Pin Description Not used (open) Key input terminal (A/D input) Not used (fixed at “H”) Detection input from the disc chucking-in detect switch “L: chucking Not used (fixed at “H”) Detection input from the loading-in detect switch “L” at a load-out position, others: “H” Not used (fixed at “H”) Detection input from the loading-out detect switch (S602) I 9, 10 NC — Not used (fixed at “L”) 11 AVSS — Ground terminal 12 XINT I 13 PDOWN I 14 NC — 15 SQSY I 16 DQSY I 17 – 19 NC — “L” at a load-out position, others: “H” Interrupt status input from the CXD2654R (IC121) Power down detection signal input terminal “L”: power down, normally: “H” Not used (fixed at “L”) Subcode Q sync (SCOR) input from the CXD2654R (IC121) “L” is input every 13.3 msec Almost all, “H” is input Digital In U-bit CD format subcode Q sync (SCOR) input from the CXD2654R (IC121) “L” is input every 13.3 msec Almost all, “H” is input Not used (fixed at “L”) System reset signal input from the reset switch (Q604) “L”: reset I 21 TEST I 22 +3.3V — 23 VBAT I Power supply for the internal real time clock and RAM 24 XOUT-T O Sub system clock output terminal (32.768 kHz) 25 XIN-T I Sub system clock input terminal (32.768 kHz) 26 GND — Ground terminal 27 XOUT O Main system clock output terminal (12 MHz) 28 XIN I Main system clock input terminal (12 MHz) 29 EXMEM I 30 S1 — Not used (open) 31 NC — Not used (fixed at “L”) 32 SENS I 33 SHOCK I 34, 35 NC — 36 STB O Relay drive signal output for the power on/off 37 REC P I Detection input from the recording position detect switch (S601) “L” active 38 PB P I Detection input from the playback position detect switch (S604) “L” active For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” Setting terminal for the test mode Not used (fixed at “L”) Power supply terminal (+3.3V) QQ 376315150 892498299 TEL 13942296513 Setting terminal external ROM mode or internal ROM mode “L”: internal ROM mode (fixed at “L”) Internal status (SENSE) input from the CXD2654R (IC121) Track jump detection signal input from the CXD2654R (IC121) Not used (fixed at “L”) “L”: standby mode, “H”: relay on Loading motor drive voltage control signal output for the loading motor driver (IC602) 39 LD-LOW O 40 NC — 41 MNT2 (XBUSY) I Busy status signal input from the CXD2654R (IC121) 42 MNT3 (SLOCK) I Spindle servo lock status monitor signal input from the CXD2654R (IC121) 43 “H” active Not used (open) LED0 O LED drive signal output terminal 44, 45 NC — Not used (fixed at “L”) 46 RST-LOW — Not used (open) 47 GND — Ground terminal www . “L”: LED on Not used (open) xiaoy u163. com – 41 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 SYS-RST QQ QQ 20 13942296513 13942296513 PACK-OUT TEL TEL 8 http://www.xiaoyu163.com QQ 376315150 892498299 Pin No. 48 Pin Name +3.3V I/O — Pin Description Power supply terminal (+3.3V) 49 SNG/CHG — 50, 51 JOG1, JOG0 I Not used (fixed at “L”) 52 SDA I/O Two-way data bus with the EEPROM (IC171) 53 SCL O Clock signal output to the EEPROM (IC171) 54 2M/4M I 55, 56 NC — 57 RXD (UART) I 58 TXD (UART) O UART communication data output to the system controller (IC401) 59 RTS I RTS (Request To Send) input from the system controller (IC401) JOG dial pulse input Not used (fixed at “L”) Select whether D-RAM capacitance 2M bit or 4M bit “L”: 4M bit (external D-RAM), “H”: 2M bit (internal D-RAM of IC121 CXD2654R) (fixed at “H” in this set) Not used (fixed at “L”) UART communication data input from the system controller (IC401) CTS O CTS (Clear To Send) output to the system controller (IC401) AUBIT0, AUBIT1 — Not used (fixed at “L”) 63, 64 CLKSET0, I Clock destination setting terminal 65 GND — Ground terminal 66 +3.3V — Power supply terminal (+3.3V) (fixed at “L”) O Serial clock signal output to the CXD2654R (IC121) SWDT O Writing data output to the CXD2654R (IC121) 69 SRDT I Reading data input from the CXD2654R (IC121) 70 EMP O Emphasis control signal output to the A/D, D/A converter (IC603) when recording mode 71 SCK1 O Display serial clock signal output terminal 72 SOUT1 O Display serial data output terminal 73 SIN1 O Chip select signal output for the display 74 CSB I Not used (fixed at “H”) 75 LDON O Laser diode on/off control signal output to the automatic power control circuit “H”: laser on 76 PIT/GRV O TEL 13942296513 77 FOK I 78 NC — 79 LOCK O Not used (open) Not used (open) QQ 376315150 892498299 Not used (open) Pit/groove detection signal output terminal “H”: is output for the playback only disc or TOC area Not used (open) Focus OK signal input from the CXD2654R (IC121) “H” is input when focus is on (“L”: NG) Not used (open) Lock signal output terminal Not used (open) Laser power select signal output to the CXD2654R (IC121) and HF module switch circuit 80 WRPWR O 81 DIG-RST O 82 NC — Not used (open) 83 DA-RST O Reset signal output to the A/D, D/A converter (IC603) 84 DSEL-A — Not used (open) 85 DSEL-B — Not used (open) “L”: playback mode, “H”: recording mode Reset signal output to the CXD2654R (IC121) and BH6511FS (IC152) “L”: reset “L”: reset Laser modulation select signal output to the HF module switch circuit Stop: “L”, Playback power: “H”, Recording power: 0.5 sec 86 MOD www O xiaoy u163. com 2 sec . – 42 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 SCLK 68 QQ QQ 67 13942296513 13942296513 CLKSET1 TEL TEL 60 61, 62 http://www.xiaoyu163.com QQ 376315150 892498299 Pin No. 87 Pin Name REC/PB I/O O Not used (open) Pin Description 88 NC — Not used (open) Recording data output enable signal output to the CXD2654R (IC121) and overwrite head 89 SCTX O driver (IC181) Writing data transmission timing output (Also serves as the magnetic head on/off output) 90 XLATCH O Serial data latch pules signal output to the CXD2654R (IC121) 91, 92 NC — Not used (open) 93 AMUTE O Muting control signal output terminal 94 LDOUT O Motor control signal output to the loading motor driver (IC602) “L” active *1 95 LDIN O Motor control signal output to the loading motor driver (IC602) “L” active *1 Not used (open) Detection input from the sled limit-in detect switch (S101) I 97 PROTECT I 98 REFLECT I 99 GND — Ground terminal 100 +3.3V — Power supply terminal (+3.3V) The optical pick-up is inner position when “L” Rec-proof claw detect input from the protect detect switch (S102-2) “H”: write protect Detection input from the disc reflection rate detect switch (S102-1) “L”: high reflection rate disc, “H”: low reflection rate disc *1 Loading motor (M103) control Mode Terminal EJECT BRAKE RUN IDLE “L” “H” “L” “H” www . “H” “L” QQ 376315150 892498299 “L” “H” xiaoy u163. com – 43 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 LDOUT (pin of) QQ QQ LDIN (pin og) LOADING 13942296513 13942296513 LIMIT-IN TEL TEL 96 http://www.xiaoyu163.com QQ 376315150 892498299 6-2. CIRCUIT BOARDS LOCATION LED board POWER board TOP board SW board BATTERY (+) board BATTERY (–) board TEL TEL BD board DG board CD MOTOR board MAIN board ANTENNA SW board FL board TUNER board JACK board www . xiaoy u163. com – 44 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 CD board QQ QQ QQ 376315150 892498299 TEL 13942296513 13942296513 13942296513 KEY board http://www.xiaoyu163.com ZS-M35 Q Q 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-3. BLOCK DIAGRAM — TUNER SECTION — TUNER BOARD ANT1 CF4 10.7MHz S607 FM ANTENNA SELECTOR TU1 8 6 +B 1 ANT 5 VT CF1 IF OUT 7 FM DET OSC OUT AM OSC CF3 4 2 AM IF-IN TBI-1 D11 24 R-CH 14 FM DET OUT Q8 11 12 CT4 FM-IN 1/2 SWALLOW COUNTER 1/16, 1/17 4BIT 11 AM-IN 17 14 13 10 TU LED 6 Q Q 12BITS PROGRAMMABLE DIVIDER Q4 16 17 PD LP-IN (Page 53) LW 20 Q6 9 MW ST-IND 8 MO/ST 13 IF-IN 10 DATA SHIFT REGISTER LATCH X OUT AM/FM 7 FM MW CCB/IF CE 6 LP-OUT X IN 1 2 CK X1 75kHz 3 4 COUNT 6 CLK 7 DATA 8 9 CE D12 VT . – 45 – x A 8 9 2 4 9 8 2 9 9 CD 19 3 7 6 3 1 5 1 5 0 MAIN SECTION RD 18 w w w TU LED PHASE DETECTOR CHARGE PUMP REFERENCE DIVIDER 04 DET OUT PLL, LOW-PASS FILTER IC2 1 3 9 4 2 2 9 6 5 1 3 CT3 Q3 RA-LCH i a o y u 1 6 3 – 46 – http://www.xiaoyu163.com 12 • SIGNAL PATH RCLOCK RADIO DATA CE VT c o : FM . COUNT DATA : AM R-CH : Same as L-CH. m – 47 – 376315150 892498299 376315150 892498299 Q2 CT2 R-OUT 2 QQ QQ T E L CT1 MUTE FM AGC Q9 L5 L4 DECODE VCO IF BUFFER CT4, L5 MW FREQUENCY COVERAGE L3 AM ANTENNA MPX-IN AM DET BAND AM OSC-IN AM MIX-OUT ST-SW MIX ST-LED AM RF-IN CT3 LW FREQUENCY COVERAGE CT1, L4 LW TRACKING 16 AM IF T1 7 CT2, L3 MW TRACKING AM/FM DET-OUT 18 BUFFER 13 13942296513 13942296513 23 1 CN1 L-OUT DIVIDE TEL TEL 21 CF2 FM IF-IN OSC OUT 8 AM FRONT-END IC1(1/2) AM RF AMP Q1 FM IF AMP Q1 IF-OUT TBI-2 FM EXT ANTENNA IF, DET, FM MPX IC1 (2/2) RADIO +B QUAD FM DET +B ON Q7 http://www.xiaoyu163.com ZS-M35 Q Q 6-4. BLOCK DIAGRAM — MD SECTION — 3 7 6 3 1 5 1 5 0 FILTER 59 62 61 SCTX AUTOMATIC POWER CONTROL Q162, 163 F TRACKING ERROR AMP COMMAND 11 APC LD/PD AMP 26 28 94 93 LASER ON SWITCH Q101 10 PD V-I CONVERTER F0CNT 12 20 3 CN602 (1/4) 16 17 18 5 21 19 16 PSB FCS– TRK+ TRK– OUT4R IN4F 4 IN2F 29 92 IN2R 30 91 3 2 1 10 XRST 13 RECP 12 OUT3F 10 OUT3R IN3F 14 IN3R 15 AUTOMATIC POWER CONTROL SFDR – 48 – SQSY 10 17 89 9 8 5 6 7 1 15 18 10 12 23 12 9 6 14 12 32 69 68 67 90 75 LDON 81 DIG-RST 80 WR-PWR 86 MOD TFDR 86 TRDR 85 . 4 LOADING MOTOR DRIVE IC602 Q Q 20 2 8 19 CN103 (1/5) FROM CPU INTERFACE (Page 53) 12 MD PLAY/REC SWITCH Q620 13 1 1, 2, 18, 19 16 3 4 17 SW IC606 XLRF 80 CKRF 81 DTRF 82 XLAT SCLK SWDT 1 2 MD MECHANISM CONTROLLER IC601 SDA 5 EEPROM IC171 SCL 6 8 9 2 4 9 8 2 9 9 XOE XWE XRAS XCAS RECP 37 CN605 (2/2) 3 3 5 5 7 7 8 6 REFERENCE VOLTAGE SWITCH Q611 CN602 (4/4) 39 LD-LOW LIMIT-IN 96 REFLECT 98 27 XOUT PROTECT 97 CN601 (2/2) SW BOARD (2/2) S601 (REC POSITION) S602 (PACK OUT) • SIGNAL PATH S604 (PLAY POSITION) : MD PLAY 8 13 11 : MD REC (DIGITAL) BD BOARD (2/2) CN103 (4/4) 16 B+ 11 S102 -1 13 -2 S101 (LIMIT IN) Q616 S102-1 (REFLECT RATE DETECT) S102-2 (PROTECT DETECT) B+ (+5V) B+ SWITCH Q617 B+ (AU +3.3V) B+ SWITCH Q612 B+ (D +5V) R-CH : Same as L-CH. MAIN BOARD (1/3) 25 XIN-T CN601 (1/2) X602 32.768kHz 3 CN602 (3/4) 2 – 49 – http://www.xiaoyu163.com CN404 (1/2) Q610 12 STB 36 SYS-RST 20 RESET SWITCH Q604 SW BOARD (1/2) 22 2 X603 22.5792MHz M103 (LOADING) 21 6 : MD REC (ANALOG) a o y u 1 6 3 CN103 (3/5) 1 B+ (D +5V) 24 XOUT-T HF MODULE SWITCH IC103, Q102 – 104 7 IC605 512FS OSC 28 XIN 2 Q 5 EMP 70 DA-RST 83 X601 12MHz 1 1 CLK 77 33 41 42 5 7 7 3 7 6 3 1 5 1 5 0 XOE 43 XWE 47 XRAS 46 XCAS 44 M i AD-LCH R-CH 4 22 16 5 CN605 (1/2) DIGITAL SERVO SIGNAL PROCESSOR IC121 (2/2) x MAIN SECTION SYSCK 9 PDDA PDAD 8 7 DQ1 – DQ4 49, 48, 50, 51 D0 – D3 A00 – A09 1 2 3 4 PACK-OUT VREF A/D CONVERTER DIGITAL SERVO SIGNAL PROCESS 17 15 DEMO 18 D-RAM IC124 PBP 38 ANALOG MUX SRDR FFDR 88 FRDR 89 8 04 14 1 67 65 66 75 74 63 64 AUTO SEQUENCER w w w HF MODULE MOD 83 SPRD 25 OUT2R IN1F 19 IN1R 18 26 7 7 SPFD 27 OUT2F 21 OUT1F 23 OUT1R 4 17 23 FIN 8 14 AUX1 ABCD FE TE SE PEAK BOTM 3 APCREF IN4R CN101 (2/2) 4 (FOCUS) (TRACKING) 2-AXIS DEVICE FCS+ M OUT4F 5 7 15 95 94 PWM GENERATOR M102 (SLED) M 6 9 CN602 (2/4) 15 DQSY CN103 (2/5) M101 (SPINDLE) 15 12 11 16 15 FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE IC152 MONITOR CONTROL SPINDLE SERVO SWDT SCLK XLAT 6 F0CNT 1 3 9 4 2 2 9 6 5 1 3 APCREF PD SE 19 A0 – A9 I-V AMP SERIAL/PARALLEL CONVERTER, DECODER LASER DIODE CPU INTERFACE 34 17 6 – 9, 11 – 15, 5 9 TE E 3 C 3 VINL 6 VINR 3 A/D CONVERTER LRCK 10 DA-LCH R-CH SERIAL INTERFACE BCK 11 8 PDOWN 13 . RXD (UART) 57 52 SDA TXD (UART) 58 53 SCL RTS 59 CTS 60 c o B+ (+3.3V) m B+ SWITCH Q603 B+ (BU +3.3V) 13 CN604 (2/2) 21 21 26 26 22 22 23 23 24 24 25 25 – 50 – SYSTEM CONTROLLER IC401(1/3) 68 REC-H 67 MD-H 66 MD-RST 63 MD-PDOWN 70 MD-STXD 69 MD-SRXD 65 MD-SCTS 64 MD-SRTS 376315150 892498299 376315150 892498299 LD 35 79 8 INTERNAL BUS DIVIDER IC123 16 34 – 31, 36 – 40, 45 ILCC 9 78 OSCO FOK SHOCK XBUSY SLOCK 17 FE FOCUS ERROR AMP 32 SCLK XLATCH F ABCD ABCD AMP I-V AMP 21 D/A CONVERTER DIN (Page 52) CN604 (1/2) VOUTL 19 VOUTR 20 QQ QQ T E L PD 18 19 20 30 SWDT SCLK XLAT C D E 29 SWDT DETECTOR B.P.F. ADIP DEMODULATOR/ DECODER SRDT 4 5 6 7 E A B C D ADFG DOUT RIN 14 ADIN OUT1 A ADFM 20 SUBCODE PROCESSOR SRDT AT AMP 36 SENS WBL J 19 CLOCK GENERATOR SPFD A DOUT 12 DIGITAL SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER IC121 (1/2) OSCI 37 EQ 3T WBL B BOTM 21 CD SECTION 13942296513 13942296513 C D PEAK & BOTTOM 12 1 B D-IN 33 SENS PEAK 3T TEMP RFI 10 B+ (+5V) 2 TEL TEL 13 57 XINT AUX F B 38 EQ WBL B.P.F. RF 14 CN603 LEVEL SHIFT IC604 D/A, A/D CONVERTER IC603 23 MNT0 MNT1 MNT2 MNT3 RF AGC & EQ 1 8 24 DIN1 FOK SHOCK MNT2 (XBUSY) MNT3 (SLOCK) AGCI DIGITAL AUDIO INTERFACE LDOUT 40 XINT 46 XBCKI +3.3V REG IC192 DADT 26 XBCK 28 LRCK 27 FS256 29 XT RFO 3 22 DIN0 COMPARATOR SCTX RF AMP J DATAI MD B+ (+3.3V) DG BOARD 9 15 ASYI LDIN 2 ASYO 25 LRCKI OUT2 1 54 I FILO SQSY 12 53 PLL CLTV DQSY J RF AMP, FOCUS/TRACKING ERROR AMP IC101 ADDT SAMPLING RATE CONVERTER PCO ADFG I CN101 (1/2) 16 MORFO OPTICAL PICK-UP BLOCK (KMS-260B) 47 MORFI 48 FILI ATRAC ENCODER/DECODER 60 SHOCK PROOF MEMORY CONTROLLER 100 EFMO SPRD 1 EFM/ACIRC ENCODER/DECODER OVER WRITE HEAD DRIVE IC181, Q181, 182 CN601 13 CN104 HR901 (OVER WRITE HEAD) I 8 9 2 4 9 8 2 9 9 CN102 BD BOARD (1/2) http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-5. BLOCK DIAGRAM — CD SECTION — CD BOARD + – 46 VC PD1 36 12 RF AMP + – 13 + – 14 9 38 7 34 35 18 FOK ADRESS DECODER OUTPUT DECODER LD TRACKING PHASE COMPENSATION PD 12 EMPH CNIN 11 SEIN 10 DATA 20 XLT 19 CLK 18 XRST 21 TTL IIL DATO 12 XLTO 13 CLKO 14 79 XRST 27 F+ (FOCUS) 1 F- CN801(1/2) 1 F– LEVEL SHIFT 2 FIN SLIN 4 18 3 17 SL– MUTE MUTE DRIVE 10 2 CN801(2/2) 15 OUT4+ M IN4 27 16 OUT4- HIGH SPEED CONTROL Q801-804 MUTE4 26 1 SERVO CONTROL 2 BUFFER IC801 MUTE Q805 19 www 04 SCOR 57 SENS 6 SQSO 5 16 16 12 15 12 15 SQCK 4 XLAT 8 CLOK 9 DATA 7 13 13 10 9 10 9 11 11 1 1 2 2 SYSTEM CONTROLLER IC401(2/3) 76 CD MUTE 62 78 CD SCOR 82 CD SENSE1 79 CD SQSO 81 84 91 83 CD SQCK CD XLAT CD CLK CD DATA XTAI 70 X701 33.8688MHz DIGITAL CLV XTAO 71 15 21 QQ 74 CD-HI SPEED 73 CD-12/8 15 3 7 6 3 1 5 1 5 0 3.3V 7 7 14 8 18 14 8 18 73 80 92 75 CD-FOK CD-XRST CD SENSE2 CD POWER 8 9 2 4 9 8 2 9 9 REG IC704 CD7V HIGH SPEED MUTE Q705 3 CD MOTOR BOARD 19 7 LIMIT SPINDLE MOTOR DRIVE IC802 10 17 CN403 (1/2) 17 SL+ M SL– 9 M801 (SPINDLE) MAIN BOARD (2/3) R-CH CN703 SL+ 8 S801 (LIMIT) 76 POWER CONTROL Q806,807 . CN706 3 3 CD12CM 5 5 MDP 6 6 MUTE 4 4 PCON CD 6V x ia o y u 1 6 3 . c o m R-CH : Same as L-CH. • SIGNAL PATH : CD PLAY : MD REC (DIGITAL) – 51 – – 52 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 4 F+ M802 (SLED) 25 T– LEVEL SHIFT 26 AOUT2 PWM TIN 1 3 9 4 2 2 9 6 5 1 3 T- MAIN SECTION D QQ QQ TEL 2 EMPHI T+ (TRACKING) CD LCH (Page 53) CPU I/F FOCUS PHASE COMPENSATION 5 5 65 SERIAL I/F SYSM 17 LEVEL SHIFT T+ 55 AOUT1 PWM SUB CODE PROCESSOR TRACKING/FOCUS COIL DRIVE, SLED MOTOR DRIVE IC703 3 54 BCKI 44 PCMDI 42 LRCKI 40 CLV SERVO F TA O PD 25 INPUT SHIFT, REGISTER APC 15 TTL FE AMP 35 BCK 43 PCMD 41 LRCK 39 D/A I/F 13942296513 LD 13942296513 AUTOMATIC POWER CONTROL Q701 E 31 C.OUT 22 SENS1 23 SENS2 24 IIL ILL DATA REGISTER 39 (Page 50) TEL TEL – + FOK XLON 10 PD2 EFM DEMO. RF SL O – + 37 FE O 11 MD SECTION B CN702 RFO – + D-OUT DIGITAL SIGNAL PROCESSOR, CLV SERVO, D/A CONVERTER IC702 RF H 32 VC 16 1 53 SPOA CN701 CN705 DOUT MDP OPTICAL PICK-UP BLOCK (KSS-213C) RF AMP, FOCUS/TRACKING SERVO IC701 http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-6. BLOCK DIAGRAM — AUDIO SECTION — MAIN BOARD (3/3) CN403(2/2) 5 CD LCH (Page 52) CN404(2/2) DA LCH MD SECTION C REC AMP IC303 8 3 AD LCH (Page 50) 20 21 22 27 7 5 XI 13 1 7 RDS DATA 9 RDS CLK 376315150 892498299 MUTE DRIVE Q312,313 35 LINE MUTE CN602 3 IR RECEIVER IC602 S601-605 CN406 11 85 1 13 CN410 60 RESET IC403 40 1 S402 (CD DOOR) QQ LED HISPEED 30 FL DIM 38 1 2 S633-638,640-646 FL DIMMER CONTROL Q430-432 X401 8KHz TOP BOARD KEY BOARD CN603 04 1-5 6-10 6-10 1-5 www X402 32kHz 5 6 AC3.5V VFL(-34V) FL DRIVER IC601 6 5 7 8 10 4 3 1 CN406 UNREG 10V REG Q403 UNREG 14V AC CHECK Q408 LED 5V REG IC411 4-39 DA 42-54 CP CS COM1 43 RESET COM2 43 FL401 FL DRIVER Q612,613 8 9 2 4 9 8 2 9 9 LED BOARD (2/2) CN602 4 10 5 6 7 8 9 9 8 7 6 5 10 12 4 2 LED DRIVE Q603,604, 606-611 CN901 3 2 CN402 AU 3.3V 63 62 61 60 COM 7V REG Q402 POWER CONTROL Q407,416 BU 3.3V REG IC404 REG IC402 x ia o y u 1 6 3 – 53 – . 3 CN902 ACCHK 8 FL-34V 6 5 FL GND 5 6 FLAC3.5V1 4 7 FLAC3.5V2 STBY CTR 2 10 9 1 BATT 7 4 c o RY901 3 FL CONT Q902 RELAY DRIVE Q901 BATT BOARD CN903 m – 54 – http://www.xiaoyu163.com T901 2 J901 AC IN POWER CONTROL Q411.412 REG Q405 COM 7V 17-21 KEY S0-S4 . 7 VFL POWER BOARD (2/2) TX 87 STBY CTR 94 ACCHK 95 51 KEY C0-C4 55-58 8 4 CN401 TEX 86 43 EXTAL CN407 3 FLAC3.5V2 REG Q406 42 XTAL FREQUENCY SHIFT Q401 FLAC3.5V1 VDD 3 7 6 3 1 5 1 5 0 POWER CONTROL Q409 RA 7V CD 6V 62 KEY AD0 61 KEY AD1 39 TU SFT 10 26 23 25 24 29 22 27 97 31 15 CD DOOR CN309 1 2 1 FL DATA 46 FL CTK 47 FL CS 45 FL RST 44 LED 0 LINE LEVEL LED 123 LED 789 LED 456 RMC LED CLOCK LED CHARA-KANA LED CHARA-ABC KEY AD2 PC ON RA POWER RST FL BOARD CN405 CN601 VDD FL AC POWER CONTROL Q419-422 98 34 33 2 CN641 S608-631 3 POWER CONTROL Q430-432 2 Q103 LINE LEVEL CONTROL Q307,309,311 CN301 BU 3.3V AU DATA 5 AU CLK 6 AU CS 4 1 3 9 4 2 2 9 6 5 1 3 LED BOARD (1/2) STANDBY CONTROL Q310 COM7V MUTE DRIVE Q305 MEGA BASS A MUTE PA STANDBY FL CTR SP201 R-CH SPEAKER 1 CN904 1 2 2 DC 4.5V 376315150 892498299 TEL R DATA 2 RCLK 16 XO 14 SP101 L-CH SPEAKER 4 Q111 CN305 J302 LINE IN TU CE TU DATA TU CLK TU COUNT X403 4.332MHz 4 CN306 QQ QQ CN303 R-CH 4 13942296513 13942296513 11 12 13 14 RDS DECODER IC405 JACK BOARD (1/2) R-CH 1 99 TU LED 4 MUX 4 J301 7 10 TU MUTE 4 5 6 7 TU CLK TU COUNT 11 i Q101 STANDBY SYSTWM CONTROLLER IC401(3/3) 3 2 TU CE TU DATA 1 CN304 1 TEL TEL (Page 47) CN301 • SIGNAL PATH : FM : CD PLAY : MD PLAY : MD REC (ANALOG) 13 14 15 MUTE DRIVE Q301,304,306 TU LED DET OUT 10 26 Q104 A MEGA BASS IC305,Q102,308 Q106 AMP Q105 1 VT OUT2 18 TONE/VOL CN408 11 RA LCH TUNER SECTION POWER AMP IC301 CS D ELECTRONIC VOLUME IC302 DAT CLK CD SECTION R-CH : Same as L-CH. JACK BOARD (2/2) http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-7. SCHEMATIC DIAGRAM — CD SECTION (1/2) — • Refer to page 97 for IC Block Diagrams. TEL TEL 13942296513 13942296513 (Page 57) Common Note on Printed Wiring Boards: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • : carbon pattern. • x : parts mounted on the conductor side. a • : Through hole. • b : Pattern from the side which enables seeing. www QQ 3 7 6 3 1 5 1 5 0 Common Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/ 4 W or less unless otherwise specified. • C : panel designation. m Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. . 8 9 2 4 9 8 2 9 9 x ia o y u 1 6 3 • • • • c o A : B+ Line. B : B– Line. H : adjustment for repair. Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions. : Impossible to measure ∗ – 55 – . • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : FM f : MW/LW E : MD PB q : MD REC (DIGITAL) j : MD REC (ANALOG) J : CD – 56 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-8. SCHEMATIC DIAGRAM — CD SECTION (2/2) — • Refer to page 97 for IC Block Diagrams. (Page 81) TEL TEL 13942296513 13942296513 (Page 84) 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 74) (Page 84) (Page 55) Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : CD STOP www • Waveforms (CD BOARD) 1 2 Approx. 1.2Vp-p 500mV/div, 500ns/div 4 Approx. 180mVp-p . IC701 ea (RFO) (CD PLAY) x ia o y u 1 6 3 3 5 1V/div, 10µs/div Approx. 120mVp-p 4.1Vp-p 22.7µs 50mV/div, 1µs/div 50mV/div, 1µs/div IC701 ra (TEO) (CD PLAY) IC701 rk (EFO) (CD PLAY) IC702 el (LRCK) (CD PLAY) – 57 – c o 6 1V/div, 200ns/div . 4.3Vp-p 470ns IC702 rd (BCK) (CD PLAY) m 4.3Vp-p 240ns IC702 rk (XPCK) (CD PLAY) – 58 – http://www.xiaoyu163.com 7 2V/div, 100ns/div 2Vp-p 0.5V/div, 10ns/div IC702 u; (XTAI) 33.9MHz 376315150 892498299 376315150 892498299 QQ 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-9. PRINTED WIRING BOARDS — CD SECTION — 1 2 3 4 5 6 7 8 9 10 11 12 13 A (Page 78) (Page 78) (Page 75) (Page 78) B TEL TEL CD MOTOR BOARD 13942296513 13942296513 C D 1 3 9 4 2 2 9 6 5 1 3 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 M M802 (SLED) S801 (LIMIT) F TP(VC) TP(TEO) M M801 (SPINDLE) TP(RFO) G 21 21 1-675-844- (21) H (21) • Semiconductor Location www . x ia o y u 1 6 3 – 59 – . c o m Ref. No. IC701 IC702 IC703 IC704 IC801 IC802 Location F-8 E-3 C-8 C-5 C-12 G-12 Q701 G-7 – 60 – http://www.xiaoyu163.com Ref. No. Q705 Q801 Q802 Q803 Q804 Q805 Q806 Q807 Location F-6 E-12 E-12 F-11 F-12 G-12 D-11 E-11 376315150 892498299 376315150 892498299 TEL QQ QQ E http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-10. PRINTED WIRING BOARDS — TUNER SECTION — 2 1 3 4 5 6 TB1-1 AM ANTENNA A 7 TB1-2 FM EXT ANTENNA 8 10 • Semiconductor Location ANTENNA SW BOARD YEL S607 FM ANTENNA SELECTOR 1 MD SHIELD BOX EXT 4 D TU1 TUNER UNIT 21 GRY F MAIN BOARD CN408 (Page 77) G H I x ia o y u 1 6 3 TP(VT) . 04 1-677-839- – 61 – . 11 (11) c o m – 62 – http://www.xiaoyu163.com Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 H-3 I-2 I-4 I-4 D-3 I-5 G-6 F-6 D-5 8 9 2 4 9 8 2 9 9 (21) 1 F-4 H-5 376315150 892498299 376315150 892498299 3 7 6 3 1 5 1 5 0 1-675-845- 8 IC1 IC2 QQ QQ QQ T E LE 1 3 9 4 2 2 9 6 5 1 3 5 Location C-7 C-7 B-6 B-6 C-5 C-5 C-4 C-4 B-3 B-3 I-4 I-7 13942296513 13942296513 BLK Ref. No. D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 TEL TEL C www 11 ANT1 FM TELSCOPIC ANTENNA TUNER BOARD B 9 http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-11. SCHEMATIC DIAGRAMS — TUNER SECTION — • Refer to page 98 for IC Block Diagrams. TEL TEL 13942296513 13942296513 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 84) www . x ia o y u 1 6 3 – 63 – . c o m • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ( ) : MW/LW – 64 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 6-12. PRINTED WIRING BOARDS — BD SECTION — 1 2 3 4 5 6 7 8 9 8 9 2 4 9 8 2 9 9 10 11 12 13 A B 1 3 9 4 2 2 9 6 5 1 3 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 F G 04 15 DG BOARD CN601 (Page 75) H 17 (REC POSITION) (LOADING) 16 DG BOARD CN602 (Page 75) DG BOARD CN605 (Page 75) • Semiconductor Location I (PACK OUT) J www . PLAY x ia o y u 1 6 3 21 (21) . c o m 1-671-115- – 65 – – 66 – http://www.xiaoyu163.com Ref. No. D101 D181 D183 Location A-1 G-6 G-6 IC101 IC103 IC121 IC123 IC124 IC152 IC171 B-12 D-2 E-12 F-4 E-13 C-9 G-1 Ref. No. IC181 IC192 Location F-10 F-9 Q101 Q102 Q103 Q104 Q162 Q163 Q181 Q182 C-13 C-2 E-1 D-2 C-13 D-13 F-10 F-11 376315150 892498299 376315150 892498299 TEL QQ QQ E 13942296513 13942296513 D TEL TEL C http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-13. SCHEMATIC DIAGRAM — BD SECTION (1/2) — • Refer to page 100 for IC Block Diagrams. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : MD STOP ( ) : MD PLAY < > : MD REC TEL TEL 13942296513 13942296513 www . QQ 3 7 6 3 1 5 1 5 0 x ia o y u 1 6 3 (Page 70) – 67 – . c o 8 9 2 4 9 8 2 9 9 m – 68 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-14. SCHEMATIC DIAGRAMS — BD SECTION (2/2) — • Refer to page 100 for IC Block Diagrams. (Page 68) • Waveforms (BD BOARD) 1 570mVp-p 200mV/div, 500ns/div IC101 1, 2 (I, J) (MD PLAY) 2 Approx. 450mVp-p Approx. 440mVp-p (Page 71) 200mV/div, 500ns/div IC101 8, 9 (E, F) (MD PLAY) 4 3.4Vp-p QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 59 8 2 9 9 1V/div, 10µs/div 4.3Vp-p 22.7µs IC121 wj (LRCK) (MD PLAY) 6 1V/div, 100ns/div (Page 71) 4.6Vp-p 354ns IC121 wk (XBCK) (MD PLAY) 7 1V/div, 50ns/div 4.8Vp-p 354ns IC121 wl (FS256) (MD PLAY) 8 1V/div, 2µs/div 4.4Vp-p 5.7µs IC121 o; (FS4) (MD PLAY) www x ia o y u 1 6 3 (Page 71) . – 69 – c o m • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : MD STOP ( ) : MD PLAY < > : MD REC . – 70 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL 1V/div, 10ns/div IC121 qh (OSCI) 45.5MHz 13942296513 13942296513 3 TEL TEL 200mV/div, 500ns/div IC101 4 (A) (MD PLAY) http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-15. SCHEMATIC DIAGRAM — DG SECTION (1/2) — • Refer to page 101 for IC Block Diagrams. • Waveforms (DG BOARD) 1 2.0Vp-p 1V/div, 50ns/div IC601 wk (XIN) 12MHz 2 1.9Vp-p TEL TEL (Page 69) 500mV/div, 10µs/div IC601 wg (XIN-T) 32.8MHz 13942296513 13942296513 3 3.4Vp-p 500mV/div, 10µs/div IC603 qa (BCK) (MD PLAY) 2.82MHz 4 1V/div, 10µs/div 3.7Vp-p TEL 1 3 9 4 2 2 9 6 5 1 3 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 4.2Vp-p 1V/div, 20ns/div IC603 9 (SYSCK) 22.6MHz 6 (Page 69) 0.8Vp-p 200mV/div, 10ns/div IC605 6 44.6MHz 376315150 892498299 376315150 892498299 5 QQ QQ 22.7µs IC603 0 (LRCK) (MD PLAY) (Page 73) www (Page 69) . • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : MD PLAY ( ) : MD STOP x ia o y u 1 6 3 – 71 – . c o m – 72 – http://www.xiaoyu163.com http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-16. SCHEMATIC DIAGRAM — DG SECTION (2/2) — • Refer to page 102 for IC Block Diagrams. TEL TEL 13942296513 13942296513 (Page 72) QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 81) www . x ia o y u 1 6 3 c o m • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : MD PLAY ( ) : MD STOP – 73 – . – 74 – http://www.xiaoyu163.com (Page 58) 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 6-17. PRINTED WIRING BOARD — DG SECTION — 2 1 3 4 5 6 7 8 (Page 78) MAIN BOARD CN404 A 8 9 2 4 9 8 2 9 9 9 10 11 12 14 DG BOARD SIDE A DG BOARD • Semiconductor Location SIDE B B BD BOARD CN102 QQ 1 3 9 4 2 2 9 6 5 1 3 15 (Page 66) 3 7 6 3 1 5 1 5 0 G BD BOARD CN103 16 (Page 66) I www 11 1-677-061- 04 J . 12 CD BOARD CN705 (11) x ia o y u 1 6 3 17 SW BOARD CN601 (Page 59) (Page 65) – 75 – . c o m 1-677-061- – 76 – http://www.xiaoyu163.com G-8 H-6 E-4 I-8 D-4 E-9 E-8 F-8 8 9 2 4 9 8 2 9 9 F H Q603 Q604 Q610 Q611 Q612 Q616 Q617 Q620 11 (11) 376315150 892498299 376315150 892498299 TEL H-9 I-8 F-9 F-11 F-10 G-11 QQ QQ E IC601 IC602 IC603 IC604 IC605 IC606 13942296513 13942296513 D Location G-6 F-8 TEL TEL C Ref. No. D602 D603 http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 6-18. PRINTED WIRING BOARD — MAIN SECTION — 2 1 A B 3 4 5 6 7 8 CD BOARD (Page 59) CN704 8 9 2 4 9 8 2 9 9 9 10 11 12 13 CD BOARD (Page 59) CN707 13 11 MAIN BOARD JACK BOARD CN304 6 (Page 86) MD SHIELD BOX POWER BOARD CN901 (Page 93) C D POWER BOARD CN902 (Page 93) R515 E 1 (Page 62) 1 3 9 4 2 2 9 6 5 1 3 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 10 F G JACK BOARD CN305 CD BOARD CN702 (Page 59) 7 (Page 86) KEY BOARD CN603 8 (Page 86) H I LED BOARD CN602 14 4 (Page 75) (Page 89) TOP BOARD CN641 (Page 89) 9 JC109 BLK JC113 BLK/GRY www S402 CD DOOR DG BOARD CN604 J JC106 JC105 . x ia o y u 1 6 3 04 – 77 – . c o m – 78 – http://www.xiaoyu163.com 5 FL BOARD CN601 (Page 86) 1-675-212- 13 376315150 892498299 376315150 892498299 TEL QQ QQ TUNER BOARD CN1 13942296513 13942296513 3 TEL TEL 2 http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-19. SCHEMATIC DIAMGRAM — MAIN SECTION (1/3) — • Refer to page 102 for IC Block Diagrams. (Page 87) (Page 84) (Page 81) TEL TEL 13942296513 13942296513 (Page 84) 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 82) (Page 87) (Page 84) (Page 82) • Semiconductor Location Ref. No. D301 D303 D304 D401 D402 D403 D404 D405 D406 D408 Location D-5 D-4 D-4 D-9 D-9 B-7 C-8 J-10 J-11 J-11 www Ref. No. IC301 IC302 IC303 IC305 IC401 IC402 IC403 IC404 IC405 IC411 . Location B-6 F-5 G-5 D-4 G-8 F-9 F-9 B-8 H-5 F-12 Ref. No. Q101 Q102 Q103 Q104 Q105 Q106 Q111 Q201 Q202 Q203 Q204 Location B-5 D-3 F-3 C-3 F-4 C-5 G-3 B-5 D-5 F-3 D-3 Ref. No. Q205 Q206 Q211 Q301 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Location F-4 C-5 G-3 D-3 D-3 C-6 D-3 E-3 D-4 E-3 D-7 Ref. No. Q311 Q312 Q313 Q401 Q402 Q403 Q405 Q406 Q407 Q408 Q409 Location E-3 F-3 D-3 H-8 B-9 B-8 C-8 I-11 B-9 E-9 H-5 Ref. No. Q411 Q412 Q415 Q416 Q419 Q420 Q421 Q422 Q430 Q431 Q432 Location C-7 C-8 I-9 B-9 I-12 I-11 I-10 J-9 J-10 J-10 J-11 x ia o y u 1 6 3 – 79 – . c o m • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM – 80 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-20. SCHEMATIC DIAMGRAM — MAIN SECTION (2/3) — • Refer to page 102 for IC Block Diagrams. (Page 83) TEL TEL (Page 92) (Page 79) QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 74) (Page 87) (Page 79) (Page 58) (Page 83) www (Page 79) . x ia o y u 1 6 3 – 81 – . c o m • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ( ) : MD STOP < > : CD STOP – 82 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL (Page 91) 13942296513 13942296513 (Page 88) http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 82) 6-21. SCHEMATIC DIAMGRAM — MAIN SECTION (3/3) — (Page 64) TEL TEL (Page 79) (Page 58) 1 3 9 4 2 2 9 6 5 1 3 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 95) (Page 82) (Page 95) www . x ia o y u 1 6 3 – 83 – . c o m Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM – 84 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL QQ QQ (Page 79) 13942296513 13942296513 (Page 58) http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-22. PRINTED WIRING BOARDS — PANEL SECTION — 1 2 3 4 5 6 7 8 9 10 A 11 12 13 14 (Page 77) FL401 FLUORESCENT INDICATOR TUBE B C 11 13942296513 13942296513 (11) (Page 78) D 11 1 3 9 4 2 2 9 6 5 1 3 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 (Page 77) F G • Semiconductor Location HIGH SPEED H 11 (11) SYMBOL I www . x ia o y u 1 6 3 – 85 – . c o m – 86 – http://www.xiaoyu163.com Ref. No. D301 D302 D303 D304 Location B-12 B-12 C-11 B-11 IC601 C-5 Q612 Q613 C-3 C-3 376315150 892498299 376315150 892498299 TEL QQ QQ (11) E TEL TEL (Page 77) http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-23. SCHEMATIC DIAMGRAMS — PANEL SECTION — • Refer to page 101 for IC Block Diagrams. (Page 79) TEL TEL 13942296513 13942296513 (Page 79) www . (Page 82) QQ 3 7 6 3 1 5 1 5 0 x ia o y u 1 6 3 . c o 8 9 2 4 9 8 2 9 9 m • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM – 87 – – 88 – http://www.xiaoyu163.com (Page 81) 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 6-24. PRINTED WIRING BOARDS — SWITCH SECTION — 2 1 3 4 5 6 7 8 9 8 9 2 4 9 8 2 9 9 10 11 12 13 14 A B TEL TEL 11 C (11) 13942296513 13942296513 (Page 77) D OPERATE QQ 1 3 9 4 2 2 9 6 5 1 3 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 F abc G H HIGH SPEED • Semiconductor Location I 11 www SYMBOL . Ref. No. D601 D602 D603 D604 D605 D606 D607 D608 D609 Location H-13 H-11 H-10 H-9 H-8 H-7 H-5 G-6 G-7 Ref. No. D610 D611 D612 D613 D614 D615 D616 D617 D618 Location G-6 G-4 G-3 G-2 H-6 H-4 H-3 H-2 H-5 x ia o y u 1 6 3 – 89 – Ref. No. D619 D620 D621 D622 D623 D624 D625 Location H-4 H-3 H-2 I-5 I-4 I-3 I-2 IC602 I-13 . Ref. No. Q603 Q604 Q606 Q607 Q608 Q609 Q610 Q611 c o Location G-13 G-12 H-5 G-7 H-3 H-4 H-5 I-5 m – 90 – http://www.xiaoyu163.com (11) 376315150 892498299 376315150 892498299 TEL (Page 77) QQ QQ E http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-25. SCHEMATIC DIAGRAMS — SWITCH SECTION — TEL TEL 13942296513 13942296513 (Page 81) www . 3 7 6 3 1 5 1 5 0 x ia o y u 1 6 3 (Page 82) – 91 – . c o 8 9 2 4 9 8 2 9 9 m • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM – 92 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-26. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A J901 AC IN • Semiconductor Location POWER BOARD LF901 Ref. No. D910 D911 D912 D913 D914 D915 Location I-4 I-3 H-4 H-5 F-7 H-5 Q901 I-6 13942296513 D 6 7 E 9 QQ 1 3 9 4 2 2 9 6 5 1 3 4 10 3BATT7(+)6BOARD3 1 5 1 5 0 DRY BATTERY UM3X3 4.5V MEMORY BACK-UP 11 F 8 BATT 9 (–)2BOARD 4 9 8 2 9 9 2 12 13 1 14 G 15 H 11 11 1-675-220- : NOT REPLACEABLE : BUILT IN TRANSFORMER I 04 www . x ia o y u 1 6 3 3 2 MAIN BOARD CN402 MAIN BOARD CN401 (Page 78) (Page 78) (11) – 93 – (11) 1 2 CN904 11 1-675-216- 1-675-221- . c o m – 94 – http://www.xiaoyu163.com (11) 376315150 892498299 376315150 892498299 TEL QQ QQ 5 8 BLK 13942296513 T901 POWER TRANSFORMER BLK/WHT TEL C Location H-6 H-7 H-6 H-7 H-5 H-6 H-5 H-5 H-3 TEL Ref. No. D901 D902 D903 D904 D905 D906 D907 D908 D909 B http://www.xiaoyu163.com ZS-M35 QQ 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 6-27. SCHEMATIC DIAGRAMS — POWER SUPPLY SECTION — TEL TEL 13942296513 13942296513 (Page 84) (Page 84) www . QQ 3 7 6 3 1 5 1 5 0 x ia o y u 1 6 3 – 95 – . c o 8 9 2 4 9 8 2 9 9 m Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM – 96 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1 3 9 4 2 2 9 6 5 1 3 QQ QQ TEL http://www.xiaoyu163.com R OUT 14 L OUT 13 36 35 34 33 FOK PILOT DEL 15 CC2 MPX IN 16 CC1 PLL IN 17 CB AM FM DET OUT DET OUT 19 18 CP AM AGC 20 RF_I AM RF IN 21 RFTC AFC 22 LD AM OSC IN 23 PD OSC OUT 24 RF_O 8 9 2 4 9 8 2 9 9 IC701 CXA2542AQ PD1 IC1 LA1833N RF_H QQ 3 7 6 3 1 5 1 5 0 6-28. IC BLOCK DIAGRAMS 32 31 30 29 28 27 26 25 VCC VCC ALC BUFF AM OSC AM MIX VEE AM RF. AMP DECODER ANTI-BIRDIE AGC AM IF VEE PD1 IV AMP AM DET VEE RF VEE SUMMING AMP VCC PD2 37 APC PD2 IV AMP COMP 24 SENS2 23 SENS1 22 C. OUT 21 XRST 20 DATA 19 XLT QQ STEREO SW 13942296513 P-DET Ø TEL AM/FM IF BUFF LEVEL DET VCC PILOT CANCEL 18 CLK 17 VCC 16 ISET 15 SL_O 14 SL_M 13 SL_P VEE LASER POWER CONTROL IFB5 IFB6 IFB4 IFB3 IFB2 IFB1 VEE – + REFERENCE DIVIDER CH2 MUTING IFIN 11 DFCTO IFB1-6 FS1-4 BAL1-4 TOG1-4 TRACKING PHASE COMPENSATION TG1 TG1-2 TM1-7 PS1-4 ISET VCC VC 46 TM4 VEE FZC COMP. VCC TM6 VCC OUT4+ OUT4– FOCUS PHASE COMPENSATION PVCC 5 6 7 8 9 10 11 12 13 14 PREGND PWGND PWGND VCCPOW OUT1– OUT1+ 4 OUT2+ 3 OUT2– 1 2 TEST 15 VDD TM5 TM3 TM7 FEO 48 VEE VEE FS1 FS2 DFCT FSET TG2 FS4 12 AMIN . x ia o y u 1 6 3 – 97 – . 4 5 6 7 8 9 10 11 12 TGU TG2 FSET TA_M TA_O 3 SRCH 2 FE_M 1 FGD www 13 FMIN FOFCT VEE 1/2 FEI SWALLOW COUNTER 1/16,1/17 4BITS DRIVER CH1 MUTE2 POWER ON RESET DRIVER CH2 CH1 MUTING UNLOCK DETECTOR 14 B04 UNIVERSAL COUNTER + – 16 VSS TM1 FZC 47 IN2 9 I02 10 THERMAL SHUTDOWN + – MUTE1 8 19 AOUT 18 AIN 17 PD TZC COMP. VCC BIAS IN1 B03 DATA SHIFT REGISTER LATCH 7 12BITS PROGRAMMABLE DIVIDER PHASE DETECTOR CHARGE PUMP IIL DATA REGISTER INPUT SHIFT REGISTER ADDRESS DECODER SENS SELECTOR OUTPUT DECODER VCC 16 15 DRIVER CH4 8 9 2 4 9 8 2 9 9 DFCT VCC DRIVER CH3 – + TTL ↓ IIL TZC 44 PVCC CH4 MUTING 20 XIN ATSC WINDOW COMP. TDFCT 45 CH3 MUTING 21 XOUT OUT3+ 23 22 21 20 19 18 17 OUT3– 24 VCC 6 VCCPOW NC 25 PWGND MUTE3 26 PWGND IN3 28 27 PRGND MUTE4 22 NC CCB I/F 3 7 6 3 1 5 1 5 0 FOH FOL TGH TGL BALH BALL ATSC TZC FZC ATSC 43 VCCPRE IN4 1 2 3 4 5 IC802 BA6892FP-E2 MIRR FOK E-F BALANCE WINDOW COMP. LPFI 42 IIL ↓ TTL c o m – 98 – http://www.xiaoyu163.com TM2 376315150 892498299 376315150 892498299 IC2 LC72137M-TLM VCC TRK. GAIN WINDOW COMP. QQ 1 3 9 4 2 2 9 6 5 1 3 VEE FO. BIAS WINDOW COMP. CC1 VEE VEE 40 INT XDFCT1 12 ST S/W DFCT2 11 BAND S/W MIRR 10 IF OUT TGFL 9 VCC LPC 8 FM DET LPCL 7 ST LED LDON 6 TU LED VEE VEE LEVEL S FE_O 5 GND E IV AMP FLB 4 AM IF IN VCC TGFL 3 REG FE AMP VCC GND TEL B02 I01 VCC TEO 41 QQ B01 F IV AMP PILOT DET TOG1 TOG2 TOG3 TOG4 2 AM MIX OUT FF 19k/0 E 39 REG 1 FM IF IN FF π 19k/2 BAL1 13942296513 NC CE DI CL DO TUNING DRIVE FM DET FF 38k BAL2 BAL3 BAL4 TEL FM IF VCO 304kHz IIL ↓ TTL VCC F 38 S-CURVE http://www.xiaoyu163.com QQ 376315150 892498299 DOUT C4M XTSL C2PO GFS XPCK XUGF VDD2 53 52 51 50 49 48 47 46 45 44 EFM DEMODULATOR VDD3 BCK PCMD EMPH 56 55 54 PCMDI WFCK 59 58 57 BCKI EXCK SBSO SCOR 60 VSS2 VSS3 EMPHI IC702 CXD3009Q 43 42 41 DIGITAL CUT SERIAL-IN INTERFACE 61 SYSM 62 ERROR CORRECTOR AVSS 63 AVDD 64 39 LRCK ASYMMETRY CORRECTOR 16K RAM PWM AIN1 66 38 37 36 35 ASYO ASYI BIAS RF 34 AVDD LOUT1 67 XVDD 69 XTAI 70 XTAO 71 TIMING LOGIC 3RD-ORDER NOISE SHAPER XVSS 72 33 32 31 30 29 DIGITAL PLL OVER SAMPLING DIGITAL FILTER AVSS 73 OSC 28 VCTL 27 V16M CLOCK GENERATOR 26 VCKI 25 VPCO LOUT2 74 PWM AIN2 75 AOUT2 76 CLTV AVSS FILI FILO PCO AVDD 77 QQ 376315150 892498299 XRST 79 15 16 17 18 19 20 FOK VDD1 VSS1 XLTO CLKO SEIN CNIN DATO 10 11 12 13 14 XLON 7 8 9 SPOA SPOB SERVO AUTO SEQUENCER DATA XLAT CLOCK LMUT RMUT 4 5 6 SQCK SQSO SENS 2 3 VSS0 1 VCC IN3' IN3 OUT3-A 24 23 22 21 20 19 18 VCC VCC – + + – REGULATOR VOLTAGE DETECT, BIAS VOLTAGE DETECT, THERMAL SHUT DOWN DRIVER MUTING xiaoy u163. com LEVEL SHIFT – + 7 8 9 10 11 12 13 14 GND IN2' IN2 OUT2-A OUT2-B GND OPOUT 6 MUTE 3 4 5 REGOUT OUT1-A 2 IN1 RESET REG-B DRIVE BUFFER DRIVE BUFFER . 15 + – + – 1 16 LEVEL SHIFT – + www 17 DRIVE BUFFER LEVEL SHIFT LEVEL SHIFT OPIN-B VCC 25 NC VREFIN 26 DRIVE BUFFER OUT3-B IN4' 27 IN4 OUT4-B 28 OUT4-A GND IC703 BA6998FP-E2 OUT1-B 376315150 892498299 CPU INTERFACE – 99 – http://www.xiaoyu163.com 22 PWM1 21 MDP 376315150 892498299 TEL 13942296513 DIGITAL CLV VDD0 80 QQ QQ 24 TEST1 23 TEST0 AVSS 78 13942296513 13942296513 AVSS 68 TEL TEL AOUT1 65 40 LRCKI DD/ /AA INTERFACE INTERFACE http://www.xiaoyu163.com IC152 BH6511FS CAPA– CAPA+ IN2R IN2F VM2 OUT2F PGND2 OUT2R VM12 OUT1R PGND1 OUT1F VM1 IN1F IN1R VDD QQ 376315150 892498299 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 AMP AMP PREDRIVE 11 12 13 PSB 14 15 16 N.C 4 OUT GND 3 PSB VM4 10 INTERFACE 5 REFERENCE VOLTAGE VCC 2 IN3R IN4F 9 VM3 IN4R 8 AMP OUT3F VG 7 OUT3R GND 6 VM34 5 OUT4R 4 PGND4 3 AMP PGND3 AMP OUT4F 2 CTL 1 PREDRIVE AMP 1 IC192 BA033FP-E2 PREDRIVE PREDRIVE INTERFACE VDD INTERFACE IN3F CHARGE PUMP. OSC AMP AMP INTERFACE TEL TEL – + AGCI RF AGC RF PEAK 44 43 42 41 40 39 38 37 USROP RF AGC + – EQ USRC DET + – RFA1 COMPO 45 COMPP OPN 46 ADDC RFO 47 OPO MORFI 48 13942296513 EQ BPF3T RFA2 I 1 J 2 –1 – –2 – RFA3 HLPT –1 + – 4 IVR WBL TEMP PEAK –2 QQ 376315150 892498299 BOTTOM PBSW GRVA WBL 35 ABCD 34 FE – – – – AA 36 BOTM PBH –1 GRV 33 AUX BPFC ABCDA 32 ADFG B + – 5 IVR C 31 ADAGC BB + – 6 IVR + + – – 30 ADIN FEA CC DET BPF22 + – 7 IVR ADIP AGC WBL ATA DD WBL E + – 8 IVR 29 ADFM + – EE EE' –1 PTGR – + – + –2 –1 TESW EBAL –2 ESW + – 9 IVR FF IV 3T xiaoy u163. com + – VREF 15 16 17 18 19 20 21 22 23 24 XLAT XSTBY F0CNT VREF EQADJ VCC 14 SCLK 13 SWDT SCRI - PARA DECODE TEMPR . 25 WBLADJ VI CONV BGR COMMAND – TEMPI APCREF 12 + GND www 26 TE TEA EQ AUXSW PD 10 TG WBL FF' FBAL GSW APC 11 + – 28 SE SEA 27 CSLED EFB F TG – 100 – http://www.xiaoyu163.com 3TADJ D – – + + 376315150 892498299 376315150 892498299 A 3 3T PTGR – 1 – –2 QQ QQ TEL 13942296513 CVB VC AUX SW PEAK3T P-P 3T –2 OFST – + 13942296513 MORFO IC101 CXA2523AR http://www.xiaoyu163.com IC121 CXD2654R MNT1 2 DCHG APC ADFG F0CNT XLRF CKRF DTRF APCREF LDDR TRDR TFDR DVDD EACH BLOCK MONITOR CONTROL MNT2 3 FFDR PWM GENERATOR SPINDLE SERVO MNT0 1 FRDR FS4 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 AUTO SEQUENCER 94 93 SRDR SFDR SPRD SPFD FGIN TEST1 TEST2 TEST3 DVSS EFMO QQ 376315150 892498299 100 99 98 97 96 95 75 TE 74 SE 73 AVSS MNT3 4 72 ADRB ADIP DECODER 71 ADRT 70 AVDD SWDT 5 69 ADIO SCLK 6 EACH BLOCK CPU I/F XLAT 7 SRDT 8 68 VC SERVO DSP SENS 9 A/D CONVERTER 67 AUX1 66 FE ANALOG MUX 65 ABCD XRST 10 64 BOTM SQSY 11 63 PEAK SUBCODE PROCESSOR DQSY 12 TEL PLL EFM/ACIRC ENCODER/ DECODER 61 FILO 60 FILI 59 PCO TX 15 13942296513 58 AVSS OSCI 16 CLOCK GENERATOR OSCO 17 XTSL 18 EACH BLOCK DIGITAL AUDIO I/F DIN0 19 DIN1 20 57 RFI COMP SAMPLING RATE CONVERTER 56 BIAS 55 AVDD 54 ASYI DOUT 21 53 ASYO DATAI 22 XBCKI 24 52 MVCI ADDT 25 ADDRESS/DATA BUS A00 - A11, D0 - D3 D2 D0 D1 XWE XRAS A09 XCAS XOE DVSS A11 A08 A07 A06 A05 A04 A10 A01 A00 A03 A02 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DVDD FS256 LRCK 26 27 28 29 30 51 D3 IC601 MSM-9202-09GS-KDR1 (FL BOARD) IC602 BA6287F OUT1 1 64 63 62 61 60 8 GND VM 2 DRIVER P1 1 P2 2 PORT DRIVER 7 OUT2 AD2 3 AD1 4 AD DRIVE DRIVER CONTROL LOGIC CONTROL CIRCUIT WRITE ADDRESS COUNTER TSD VCC 3 8BIT SHIFT REGISTER ADDRESS SELECTOR www ADRAM 16Wx2B 5 RIN CGROM 248Wx35B SEG1 5 OSCILLATOR DUTY CONTROL 59 OSC1 58 OSC0 57 GND 56 VFL DIGIT CONTROL xiaoy u163. com DCRAM 16Wx8B . TIMING GENERATOR1 COMMAND DECODER TIMING GENERATOR2 6 VREF POWER SAVE FIN 4 READ ADDRESS COUNTER VDD DA CP CS RESET GRID DRIVER 55 COM16 40 COM1 CGRAM 8Wx35B SEGMENT DRIVE SEG28 32 – 101 – http://www.xiaoyu163.com 39 SEG35 33 SEG29 376315150 892498299 376315150 892498299 ATRAC ENCODER/DECODER LRCKI 23 QQ QQ QQ 376315150 892498299 TEL 13942296513 XBCK 13942296513 SHOCK RESISTANT MEMORY CONTROLLER XINT 14 DADT TEL 62 CLTV RECP 13 http://www.xiaoyu163.com QQ 376315150 892498299 IC603 PCM3003E/T2 VCC1 VCC1 1 2 VINR 3 VREF1 4 VREF2 5 VINL 6 PDAD 7 PDDA 8 SYSCK A/D CONVERTER BLOCK D/A CONVERTER BLOCK ANALOG FRONT-END CIRCUIT ANALOG FRONT-END CIRCUIT ∆Σ MODULATOR ∆Σ MODULATOR DECIMATION & LOW CUT FILTER DECIMATION & LOW CUT FILTER ANALOG LOW-PASS FILTER ANALOG LOW-PASS FILTER MULTI-LEVEL ∆Σ MODULATOR MULTI-LEVEL ∆Σ MODULATOR INTERPOLATION FILTER X8 OVERSAMPLING INTERPOLATION FILTER X8 OVERSAMPLING VCC2 AGND1 AGND2 VCOM VOUTR VOUTL 18 17 16 15 14 13 DEM0 DEM1 20BIT DIN VDD DGND REFERENCE RESET & POWER DOWN 9 CLOCK TEL TEL SERIAL INTERFACE LRCIN 10 BCKIN 11 DOUT 12 MODE CONTROL INTERFACE RECOUT2 SIMIN2 SIMOUT2 BASS2 CH2IN2 CH2IN3 CH2IN4 TRF2 OUT2 AGND DVDD CS 28 27 26 25 24 23 22 21 20 19 18 17 16 15 AVDD CH2IN1 IC411 XC62FP3302PR VOUT 1 VIN 2 VR3 SIMAMP2 VR5 VREF VSS 3 TONE AMP2 VR2 CONTROL LOGIC VOLAMP2 VOLAMP1 VR1 TONE AMP1 REF VR5 SIMAMP1 xiaoy u163. com 9 CH1IN4 10 11 12 13 14 OUT1 DGND DAT CLK 8 TER1 7 CH1IN3 SIMIN1 . 6 CH1IN2 RECOUT1 5 BASS1 4 SIMOUT1 3 REF CH1IN1 www 1 2 VR3 – 102 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 IC302 M62443FPD61Q QQ QQ QQ 376315150 892498299 TEL 13942296513 13942296513 13942296513 24 23 22 21 20 19 http://www.xiaoyu163.com SECTION 7 EXPLODED VIEWS QQ 376315150 892498299 NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Abbreviation CET : East European & CIS model The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color • Accessories and packing materials are given in the last of this parts list. 7-1. CABINET (REAR) SECTION TEL TEL 3 13942296513 13942296513 #3 ANT1 #2 #2 #3 B QQ #11 376315150 892498299 #2 T901 #11 F903 8 F902 #3 1 A 7 B 5 Ref. No. Part No. Description * 1 * 2 3 4 * 5 A-3322-536-A 3-039-987-01 3-039-974-01 3-039-976-01 1-675-221-21 POWER BOARD, COMPLETE CHASSIS, TRANSFORMER HANDLE LID, BATTERY CASE BATT (–) BOARD Remark #3 6 Ref. No. Part No. Description 8 * 9 ANT1 0 F901 0 F902 3-039-967-01 1-675-220-21 1-501-452-11 1-532-467-51 1-532-388-51 TERMINAL (BATT –), BATTERY BATT (+) BOARD ANTENNA, TELESCOPIC FUSE (315mA/250V) FUSE (2A/250V) 0 F903 0 T901 1-532-464-51 FUSE (2.5A/250V) 1-435-321-11 TRANSFORMER, POWER xiaoy u163. com 3-039-958-01 TERMINAL, ANTENNA 3-039-971-41 CABINET (REAR) . #1 8 #3 www #2 9 F901 6 7 #2 – 103 – http://www.xiaoyu163.com Remark 376315150 892498299 376315150 892498299 TEL 13942296513 #7 #1 QQ QQ 2 4 #1 #1 A http://www.xiaoyu163.com QQ 376315150 892498299 7-2. CABINET (FRONT) SECTION 68 58 C 57 65 #3 SP101 65 65 65 59 13942296513 67 #3 60 13942296513 65 65 65 #3 TEL TEL 56 not supplied 66 61 #3 54 64 55 65 #3 62 #3 #3 QQ not supplied #3 69 #3 376315150 892498299 SP201 63 51(including #3 ) 52 53 Ref. No. * * * * Part No. Description 51 52 53 54 55 X-3378-656-1 3-040-916-01 X-3377-977-1 3-039-977-02 3-040-704-01 CABINET FRONT (SUB) ASSY FOOT (F), RUBBER CHASSIS ASSY, NET WINDOW (FL) BUTTON (REC) (4P) 56 57 58 59 60 1-675-223-21 A-3322-525-A 1-675-213-13 1-675-845-21 1-791-523-11 KEY BOARD LED BOARD, COMPLETE TOP BOARD ANTENNA SW BOARD WIRE, PARALLEL (FFC) (13 CORE) 61 www . Remark Ref. No. Part No. Description * 62 * 63 64 65 66 A-3322-527-A 1-675-219-21 3-039-979-01 4-951-620-01 3-041-800-01 TUNER BOARD, COMPLETE JACK BOARD BUTTON (10 KEY) SCREW (2.6X8), +BVTP SHEET (A), ADHESIVE 3-041-801-01 X-3378-404-1 3-039-954-01 1-529-463-11 1-529-463-11 SHEET (B), ADHESIVE BUTTON (TOP) ASSY PLATE (10 KEY), LIGHT GUIDE SPEAKER (8cm) (L-CH) SPEAKER (8cm) (R-CH) 67 68 69 SP101 SP201 xiaoy u163. com 1-791-522-11 WIRE, PARALLEL (FFC) (10 CORE) – 104 – http://www.xiaoyu163.com Remark 376315150 892498299 QQ 376315150 892498299 TEL 13942296513 QQ 65 C http://www.xiaoyu163.com QQ 376315150 892498299 7-3. CABINET (UPPER) SECTION S402 106 108 109 not supplied 111 112 107 110 113 TEL TEL #3 #4 #3 #3 115 105 117 115 not supplied not supplied 117 117 104 #3 116 QQ 376315150 892498299 102 103 117 118 119 101 #3 #3 Ref. No. Part No. Description Part No. Description * 101 102 103 * 104 105 A-3322-530-A 3-039-961-01 1-791-521-11 A-3322-528-A 3-039-978-01 MAIN BOARD, COMPLETE SPRING (IC) WIRE, PARALLEL (FFC) (10 CORE) FL BOARD, COMPLETE HOLDER (FL) 112 113 114 115 116 1-452-899-11 3-036-467-01 3-923-736-01 3-931-379-31 3-931-379-21 MAGNET PLATE, CHUCKING COVER, CD RUBBER, VIBRATION PROOF RUBBER, VIBRATION PROOF 106 * 107 108 109 110 1-791-520-11 A-3322-529-A 3-039-972-01 3-039-957-01 3-922-112-31 WIRE, PARALLEL (FFC) (18 CORE) CD BOARD, COMPLETE CABINET (UPPER) SPRING (CD UP) DAMPER 117 118 * 119 FL401 S402 3-921-725-01 1-791-518-11 A-3322-538-A 1-517-916-11 1-692-960-11 SCREW (2.6X10), +PWH WIRE, PARALLEL (FFC) (16 CORE) CD MOTOR BOARD, COMPLETE INDICATOR TUBE, FLUORESCENT SWITCH, PUSH (1 KEY) (CD DOOR) 111 . Remark #3 Ref. No. xiaoy u163. com 3-039-975-11 LID, CD – 105 – http://www.xiaoyu163.com Remark 376315150 892498299 376315150 892498299 TEL 13942296513 116 #3 QQ QQ FL401 www 13942296513 13942296513 114 #3 http://www.xiaoyu163.com QQ 376315150 892498299 7-4. MD BLOCK SECTION MDM-5GA 153 153 151 152 TEL TEL #5 13942296513 13942296513 not supplied not supplied not supplied #5 not supplied 154 158 155 #5 #5 #5 #5 159 #5 #5 #5 Ref. No. 151 152 153 154 155 Part No. Description 3-036-318-11 3-036-311-01 3-042-390-01 1-791-519-11 1-791-531-21 CARTRIDGE, LID SPRING (MD LID) SCREW (+BVTTWH M3), STEP WIRE, PARALLEL (FFC) (26 CORE) WIRE, PARALLEL (FFC) (21 CORE) www . Remark #5 Ref. No. Part No. Description 156 * 157 158 159 1-791-532-21 A-3322-531-A 3-041-799-01 X-3378-454-1 WIRE, PARALLEL (FFC) (23 CORE) DG BOARD, COMPLETE SHEET, INSULATING PLATE (LOWER) ASSY, SHIELD xiaoy u163. com – 106 – http://www.xiaoyu163.com Remark 376315150 892498299 376315150 892498299 QQ 376315150 892498299 TEL 13942296513 QQ QQ 156 157 http://www.xiaoyu163.com QQ 376315150 892498299 7-5. MD MECHANISM SECTION (MDM-5GA) 224 213 211 212 213 217 218 210 214 207 221 220 215 TEL TEL 209 219 208 #6 223 203 225 203 202 #6 201 226 206 #4 204 M103 205 MBU-5A #6 Ref. No. Part No. Description * 201 * 202 203 * 204 205 1-671-115-21 4-996-217-01 4-996-223-11 4-996-218-01 4-996-277-01 SW BOARD CHASSIS INSULATOR (F) BRACKET (GUIDE R) SPRING (O/C), TENSION 206 207 * 208 209 210 4-996-226-01 4-999-347-01 4-996-225-01 4-988-466-11 4-996-219-01 LEVER (O/C) INSULATOR (R) BRACKET (GUIDE L) SPRING (ELECTROSTATIC), LEAF GEAR (CAM GEAR) 211 212 213 214 4-996-220-01 4-996-221-01 4-933-134-01 4-996-224-01 www . Remark Ref. No. Part No. Description 215 216 217 218 219 4-996-227-11 4-996-229-01 4-996-212-01 4-996-213-01 4-996-214-01 LEVER (HEAD) SPRING (HEAD LEVER), TORSION LEVER (LIMITTER) SPRING (LIMITTER), TORSION SPRING (SLIDER), TENSION 220 221 222 223 * 224 4-996-216-01 4-996-215-11 X-4949-668-3 X-4949-667-4 4-996-211-11 SPRING (HOLDER), TENSION SPRING (LOCK LEVER), TENSION SLIDER ASSY HOLDER ASSY SLIDER (CAM) xiaoy u163. com GEAR (A) GEAR (B) SCREW (+PTPWH M2.6X6) SCREW (1.7X3), +PWH 225 226 M103 Remark 4-998-763-03 SPRING (SHUTTER), LEAF A-4680-200-G HOLDER COMPLETE ASSY X-4949-264-1 MOTOR ASSY, LOADING (LOADING) (MD) – 107 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 TEL 13942296513 QQ QQ 207 13942296513 13942296513 222 216 http://www.xiaoyu163.com QQ 376315150 892498299 7-6. MD BASE UNIT SECTION (MBU-5A) 252 #8 265 264 HR901 266 271 #9 263 267 #8 270 268 #8 not supplied 269 TEL TEL 262 272 261 #8 not supplied 256 #10 M101 259 #9 273 S102 255 13942296513 13942296513 #8 260 #8 258 257 252 253 M102 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 251 252 Ref. No. Part No. Description 251 252 * 253 * 254 255 A-4699-893-A 3-372-761-01 4-996-267-01 4-996-255-01 4-900-590-01 BD BOARD, COMPLETE SCREW (M1.7), TAPPING BASE (BU-D) BASE (BU-C) SCREW, PRECISION SMALL 256 257 * 258 * 259 0 260 4-996-258-01 4-996-262-01 1-667-954-11 4-210-664-11 A-4672-541-A SPRING, COMPRESSION GEAR (SL-C) FLEXIBLE BOARD BASE (BU-A) PICK-UP ASSY, OPTICAL KMS-260B (MD) * 261 * 262 263 264 4-996-252-01 4-996-254-01 4-967-688-11 4-996-260-01 CHASSIS, BU BASE (BU-B) MAGNET, ABSORPTION GEAR (SL-A) www Remark Ref. No. Part No. Description 265 266 267 268 269 4-996-261-01 4-996-264-01 4-996-265-01 4-996-256-11 4-996-257-01 GEAR (SL-B) SPRING (SHAFT), LEAF SHAFT, MAIN SL (BASE) RACK (SL) 270 271 272 273 4-996-263-01 4-988-560-01 4-211-036-01 A-4672-475-A . SPRING (CLV), TORSION SCREW (+P 1.7X6) SCREW (1.7X2.5), +PWH MOTOR ASSY, SPINDLE (SPINDLE) (INCLUDING M101) (MD) 1-500-502-11 HEAD, OVER WRITE xiaoy u163. com HR901 M102 S102 Remark A-4672-474-A MOTOR ASSY, SLED (SLED) (MD) 1-762-148-21 SWITCH, PUSH (2 KEY) (REFLECT RATE DETECT,PROTECT DETECT) – 108 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 TEL 13942296513 #8 QQ QQ 254 http://www.xiaoyu163.com QQ 376315150 892498299 7-7. OPTICAL PICK-UP SECTION (KSM-213CDM) 303 not supplied 305 TEL TEL 13942296513 13942296513 302 306 301 304 M701 M702 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description 301 302 0 303 304 2-626-908-01 3-713-786-51 8-848-483-05 X-2626-202-1 SHAFT, SLED SCREW +P 2X3 PICK-UP, OPTICAL KSS-213C (CD) CHASSIS ASSY, MOTOR (MB) (SPINDLE) (INCLUDING M701) (CD) www . Remark Ref. No. 305 306 M702 Part No. Description Remark 2-626-907-01 GEAR (A) 2-627-003-02 GEAR (B) (RP) X-2625-769-1 GEAR ASSY, MOTOR (MB) (RP) (SLED) (CD) xiaoy u163. com – 109 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 QQ QQ TEL 13942296513 http://www.xiaoyu163.com ANTENNA SW BATT (+) SECTION 8 ELECTRICAL PARTS LIST QQ 376315150 892498299 BATT (–) BD NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • Abbreviation CET : East European & CIS model • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. Description Remark * 1-675-845-21 ANTENNA SW BOARD ****************** < SWITCH > 1-675-220-21 BATT (+) BOARD ************** 3-039-967-01 TERMINAL (BATT –), BATTERY ************************************************************* A-4699-893-A BD BOARD, COMPLETE ******************* Remark C130 C131 C132 C133 C134 1-163-251-11 1-163-023-00 1-107-823-11 1-163-017-00 1-163-038-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 0.015uF 0.47uF 0.0047uF 0.1uF C135 C136 C142 C143 C144 1-163-038-00 1-126-206-11 1-163-251-11 1-163-251-11 1-163-251-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 100uF 100PF 100PF 100PF C146 C151 C152 C153 C156 1-163-038-00 1-126-206-11 1-163-038-00 1-163-021-11 1-163-038-00 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 100uF 0.1uF 0.01uF 0.1uF C158 C160 C161 C163 C164 1-163-019-00 1-104-601-11 1-104-601-11 1-163-021-11 1-163-021-11 CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.0068uF 10uF 10uF 0.01uF 0.01uF C167 C168 C169 C171 C181 1-163-038-00 1-163-038-00 1-125-822-11 1-163-038-00 1-104-913-11 CERAMIC CHIP CERAMIC CHIP TANTALUM CERAMIC CHIP TANTAL. CHIP 0.1uF 0.1uF 10uF 0.1uF 10uF C183 C184 0 C185 C187 C188 1-163-038-00 1-117-970-11 1-164-611-11 1-104-913-11 1-163-021-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP 0.1uF 22uF 0.001uF 10uF 0.01uF C189 C190 C191 C196 C197 1-163-989-11 1-126-206-11 1-163-038-00 1-163-038-00 1-163-038-00 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.033uF 100uF 0.1uF 0.1uF 0.1uF 5% 5% 10% 5% 20% 5% 5% 5% 20% 10% 50V 50V 16V 50V 25V 25V 6.3V 50V 50V 50V 25V 6.3V 25V 50V 25V QQ 376315150 892498299 10% 20% 20% 10% 10% 50V 10V 10V 50V 50V 20% 20% 25V 25V 10V 25V 16V 20% 10% 20% 10% 25V 10V 500V 16V 50V < CAPACITOR > C101 C102 C103 C104 C105 1-125-822-11 1-163-038-00 1-125-822-11 1-125-822-11 1-163-021-11 TANTALUM CERAMIC CHIP TANTALUM TANTALUM CERAMIC CHIP 10uF 0.1uF 10uF 10uF 0.01uF 20% C106 C107 C108 C109 C111 1-163-275-11 1-163-038-00 1-163-038-00 1-163-037-11 1-164-344-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.1uF 0.022uF 0.068uF 5% 10% 10% 50V 25V 25V 25V 25V C112 C113 C115 C116 C117 1-163-017-00 1-109-982-11 1-164-489-11 1-163-037-11 1-163-809-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0047uF 1uF 0.22uF 0.022uF 0.047uF 5% 10% 10% 10% 10% 50V 10V 16V 25V 25V C118 C119 C121 C122 C123 1-163-038-00 1-125-822-11 1-125-822-11 1-163-021-11 1-163-038-00 CERAMIC CHIP TANTALUM TANTALUM CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 10uF 0.01uF 0.1uF 20% 20% 10% 25V 10V 10V 50V 25V C124 C127 C128 C129 1-163-038-00 1-163-038-00 1-163-021-11 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.01uF 0.47uF 20% 20% 10% 10V 25V 10V 10V 50V 10% 20% < CONNECTOR > www . CN101 CN102 CN103 CN104 CN110 1-569-479-51 1-784-833-21 1-784-834-21 1-770-687-11 1-695-440-21 CONNECTOR, FPC 21P CONNECTOR, FFC (LIF(NON-ZIF)) 21P CONNECTOR, FFC (LIF(NON-ZIF)) 23P CONNECTOR, FFC/FPC 4P PIN, CONNECTOR (PC BOARD) 6P xiaoy u163. com 10% 10% 25V 25V 50V 16V < DIODE > D101 8-719-988-61 DIODE 1SS355TE-17 – 110 – http://www.xiaoyu163.com 25V 6.3V 25V 25V 25V 376315150 892498299 376315150 892498299 TEL 13942296513 3-039-967-01 TERMINAL (BATT –), BATTERY ************************************************************* Description QQ QQ 1-675-221-21 BATT (–) BOARD ************** Part No. 13942296513 13942296513 S607 1-771-672-11 SWITCH, SLIDE (FM ANTENNA SELECTOR) ************************************************************* Ref. No. TEL TEL Part No. * When indicating parts by reference number, please include the board. • CAPACITORS uF : µF • COILS uH : µH Ref. No. * The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. http://www.xiaoyu163.com QQ 376315150 892498299 BD Ref. No. D181 D183 Part No. Description Remark Description 1-216-025-11 1-216-097-11 1-216-295-00 1-216-025-11 1-216-025-11 RES-CHIP RES-CHIP SHORT RES-CHIP RES-CHIP 100 100K 0 100 100 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R127 R129 R130 R131 R132 1-216-025-11 1-216-295-00 1-216-295-00 1-216-073-00 1-216-097-11 RES-CHIP SHORT SHORT METAL CHIP RES-CHIP 100 0 0 10K 100K 5% 1/10W 5% 5% 1/10W 1/10W 1-216-117-00 1-216-049-11 1-216-061-00 1-216-049-11 1-216-295-00 METAL CHIP RES-CHIP METAL CHIP RES-CHIP SHORT 680K 1K 3.3K 1K 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W < COIL > R133 R134 R135 R136 R137 < IC > IC101 IC103 IC121 IC123 IC124 8-752-080-95 8-729-903-10 8-752-389-44 8-759-096-87 8-759-334-38 IC CXA2523AR TRANSISTOR FMW1-T-148 IC CXD2654R IC TC7WU04FU(TE12R) IC MN41V4400TT-08 IC152 IC171 IC181 IC192 8-759-430-25 8-759-487-04 8-759-481-17 8-759-460-72 IC IC IC IC BH6511FS-E2 BR24C02F-E2 MC74ACT08DTR2 BA033FP-E2 Ref. No. Remark TEL R140 R142 R143 R144 R145 1-216-029-00 1-216-073-00 1-216-073-00 1-216-025-11 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 150 10K 10K 100 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W L121 L122 L151 L152 L153 1-414-813-11 1-414-813-11 1-412-029-11 1-412-029-11 1-412-032-11 FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR INDUCTOR CHIP 10uH INDUCTOR CHIP 10uH INDUCTOR CHIP 100uH R146 R147 R148 R149 R150 1-216-037-00 1-216-025-11 1-216-045-00 1-216-073-00 1-216-295-00 METAL CHIP RES-CHIP METAL CHIP METAL CHIP SHORT 330 100 680 10K 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W L154 L161 L162 L181 1-412-032-11 1-414-813-11 1-414-813-11 1-216-295-00 INDUCTOR CHIP 100uH FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR SHORT 0 R151 R152 R158 R159 R160 1-216-073-00 1-216-073-00 1-216-097-11 1-216-097-11 1-216-295-00 METAL CHIP METAL CHIP RES-CHIP RES-CHIP SHORT 10K 10K 100K 100K 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R161 R162 R163 R164 R165 1-216-057-00 1-216-057-00 1-216-057-00 1-216-045-00 1-216-097-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 2.2K 2.2K 2.2K 680 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R166 R167 R169 R170 R171 1-216-298-00 1-216-065-11 1-219-724-11 1-216-073-00 1-216-073-00 METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 2.2 4.7K 1 10K 10K 5% 5% 1% 5% 5% 1/10W 1/10W 1/4W 1/10W 1/10W R173 R175 R177 R179 R180 1-216-121-11 1-216-065-11 1-216-061-00 1-216-085-00 1-216-073-00 RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 1M 4.7K 3.3K 33K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R182 R183 R184 R185 R186 1-216-089-11 1-216-089-11 1-216-073-00 1-216-081-00 1-216-089-11 RES-CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP 47K 47K 10K 22K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R188 R189 R190 1-216-073-00 METAL CHIP 1-216-073-00 METAL CHIP 1-216-073-00 METAL CHIP 10K 10K 10K 5% 5% 5% 1/10W 1/10W 1/10W QQ 376315150 892498299 TEL 13942296513 < TRANSISTOR > Q101 Q102 Q103 Q104 Q162 8-729-403-35 8-729-026-53 8-729-402-93 8-729-402-93 8-729-101-07 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN5113-TX 2SA1576A-T106-QR UN5214-TX UN5214-TX 2SB798-T1DK Q163 Q181 Q182 8-729-403-35 TRANSISTOR UN5113-TX 8-729-018-75 TRANSISTOR 2SJ278MYTR 8-729-017-65 TRANSISTOR 2SK1764KYTR < RESISTOR > R103 R104 R105 R106 R107 1-216-049-11 1-216-073-00 1-216-065-11 1-216-133-00 1-216-113-00 RES-CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 1K 10K 4.7K 3.3M 470K R109 R110 R111 R112 R113 1-216-295-00 1-216-073-00 1-216-295-00 1-216-089-11 1-216-049-11 SHORT METAL CHIP SHORT RES-CHIP RES-CHIP 0 10K 0 47K 1K 5% 1/10W 5% 5% 1/10W 1/10W R115 R117 1-216-049-11 RES-CHIP 1-216-113-00 METAL CHIP 1K 470K 5% 5% 1/10W 1/10W www . 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W xiaoy u163. com – 111 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR QQ QQ 1-414-813-11 1-414-813-11 1-414-813-11 1-414-813-11 1-414-813-11 13942296513 13942296513 L101 L102 L103 L105 L106 TEL Part No. R120 R121 R123 R124 R125 8-719-046-86 DIODE F1J6TP 8-719-046-86 DIODE F1J6TP http://www.xiaoyu163.com QQ 376315150 892498299 BD Ref. No. R195 R196 R197 R198 CD Part No. Description 1-216-073-00 1-216-295-00 1-216-295-00 1-216-296-00 METAL CHIP SHORT SHORT SHORT Remark 10K 0 0 0 5% 1/10W Ref. No. Part No. Description C740 C743 C744 C745 C746 1-163-021-11 1-163-021-11 1-163-251-11 1-163-011-11 1-163-001-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 100PF 0.0015uF 220PF 10% 10% 5% 10% 10% 50V 50V 50V 50V 50V Remark C747 C748 C749 C750 C752 1-164-489-11 1-163-809-11 1-163-021-11 1-163-021-11 1-163-021-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.22uF 0.047uF 0.01uF 0.01uF 0.01uF 10% 10% 10% 10% 10% 16V 25V 50V 50V 50V C753 C754 C755 C756 C757 1-163-021-11 1-163-021-11 1-163-251-11 1-163-263-11 1-163-021-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 100PF 330PF 0.01uF 10% 10% 5% 5% 10% 50V 50V 50V 50V 50V C758 C759 C760 C762 C763 1-163-251-11 1-163-017-00 1-163-017-00 1-163-021-11 1-163-259-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 0.0047uF 0.0047uF 0.01uF 220PF 5% 5% 5% 10% 5% 50V 50V 50V 50V 50V C764 C765 C766 C767 C768 1-163-021-11 1-163-021-11 1-104-665-11 1-163-229-11 1-163-229-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 100uF 12PF 12PF 10% 10% 20% 5% 5% 50V 50V 10V 50V 50V C769 C770 C773 C774 C775 1-104-665-11 1-104-665-11 1-126-964-11 1-126-964-11 1-163-021-11 ELECT ELECT ELECT ELECT CERAMIC CHIP 100uF 100uF 10uF 10uF 0.01uF 20% 20% 20% 20% 10% 10V 10V 50V 50V 50V C776 C777 C778 C780 C781 1-115-566-11 1-104-665-11 1-163-021-11 1-163-239-11 1-163-021-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 100uF 0.01uF 33PF 0.01uF 10% 20% 10% 5% 10% 10V 10V 50V 50V 50V C782 C783 C790 1-163-021-11 CERAMIC CHIP 1-163-021-11 CERAMIC CHIP 1-163-251-11 CERAMIC CHIP 0.01uF 0.01uF 100PF 10% 10% 5% 50V 50V 50V < SWITCH > S101 S102 1-762-596-21 SWITCH, PUSH (1 KEY) (LIMIT IN) 1-762-148-21 SWITCH, PUSH (2 KEY) (REFLECT RATE DETECT,PROTECT DETECT) ************************************************************* A-3322-529-A CD BOARD, COMPLETE ******************* * < CAPACITOR > 20% 10% 10% 10% 5% 10V 50V 50V 25V 50V C706 C707 C708 C709 C710 1-163-021-11 1-126-925-11 1-107-725-11 1-163-019-00 1-107-725-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 470uF 0.1uF 0.0068uF 0.1uF 10% 20% 10% 10% 10% 50V 10V 16V 50V 16V C711 C712 C713 C714 C715 1-107-725-11 1-163-037-11 1-104-664-11 1-164-161-11 1-107-725-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.1uF 0.022uF 47uF 0.0022uF 0.1uF 10% 10% 20% 10% 10% 16V 25V 10V 100V 16V C716 C717 C718 C719 C720 1-126-964-11 1-107-725-11 1-107-725-11 1-163-227-11 1-115-566-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 0.1uF 10PF 4.7uF 20% 10% 10% 0.50PF 10% 50V 16V 16V 50V 10V C721 C722 C723 C724 C725 1-163-021-11 1-163-989-11 1-163-989-11 1-163-091-00 1-163-133-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.033uF 0.033uF 8PF 470PF 10% 10% 10% 5% 50V 25V 25V 50V 50V C726 C727 C728 C729 C730 1-163-021-11 1-107-725-11 1-163-227-11 1-163-059-11 1-125-838-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.1uF 10PF 0.01uF 2.2uF 10% 10% 0.50PF 10% 10% 50V 16V 50V 50V 6.3V C731 C732 C733 C734 C735 1-164-344-11 1-163-989-11 1-163-243-11 1-163-009-11 1-163-021-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.068uF 0.033uF 47PF 0.001uF 0.01uF 10% 10% 5% 10% 10% 25V 25V 50V 50V 50V C736 C737 C738 C739 1-104-665-11 1-163-251-11 1-163-251-11 1-163-251-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100uF 100PF 100PF 100PF 20% 5% 5% 5% 10V 50V 50V 50V TEL 13942296513 QQ 376315150 892498299 < CONNECTOR > www . CN701 * CN702 CN704 * CN705 * CN707 1-770-646-11 1-691-077-21 1-569-614-11 1-785-654-11 1-573-455-11 CONNECTOR, FFC/FPC 16P HOUSING, CONNECTOR 18P PLUG, CONNECTOR 2P PIN, CONNECTOR (PC BOARD) 2P PLUG, CONNECTOR 4P < FERRITE BEAD > FB701 FB702 FB703 FB704 FB713 1-216-295-00 1-216-295-00 1-469-180-22 1-469-180-22 1-216-295-00 SHORT 0 SHORT 0 FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR SHORT 0 FB714 1-216-295-00 SHORT 0 xiaoy u163. com – 112 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 100uF 0.01uF 0.001uF 0.047uF 0.0047uF QQ QQ ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 13942296513 13942296513 1-104-665-11 1-163-021-11 1-163-009-11 1-163-809-11 1-163-017-00 TEL TEL C701 C702 C703 C704 C705 http://www.xiaoyu163.com QQ 376315150 892498299 CD Ref. No. Part No. Description Remark < IC > IC701 IC702 IC703 IC704 8-752-083-24 8-752-387-78 8-759-591-62 8-759-652-44 IC IC IC IC CXA2542AQ CXD3009Q BA6998FP-E2 BA033ST-V5 < JUMPER RESISTOR > SHORT SHORT SHORT SHORT RES-CHIP 0 0 0 0 1K JC708 JC709 JC711 JC713 JC715 1-216-295-00 1-216-295-00 1-216-296-00 1-216-295-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 JC720 JC721 JC723 JC725 JC730 1-216-295-00 1-216-295-00 1-216-049-11 1-216-295-00 1-216-295-00 SHORT SHORT RES-CHIP SHORT SHORT 0 0 1K 0 0 JC734 JC739 1-216-295-00 SHORT 1-216-295-00 SHORT 5% 5% 1/10W 0 0 5% Q701 Q705 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R726 R731 R732 R733 R734 1-216-097-11 1-216-081-00 1-216-081-00 1-216-097-11 1-216-001-00 RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 100K 22K 22K 100K 10 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R735 R737 R738 R741 R742 1-216-065-11 1-216-089-11 1-216-069-00 1-216-105-11 1-216-101-00 RES-CHIP RES-CHIP METAL CHIP RES-CHIP METAL CHIP 4.7K 47K 6.8K 220K 150K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R743 R745 R750 R751 R752 1-216-101-00 1-216-109-00 1-216-076-00 1-216-077-11 1-216-085-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 150K 330K 13K 15K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R758 R760 R762 R763 R764 1-216-218-00 1-216-097-11 1-216-113-00 1-216-061-00 1-216-061-00 RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 6.8K 100K 470K 3.3K 3.3K 5% 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/10W 1/10W R765 R766 R767 R768 R770 1-216-073-00 1-216-121-11 1-216-073-00 1-216-105-11 1-216-049-11 METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 10K 1M 10K 220K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R771 R776 R777 R778 R780 1-216-025-11 1-216-073-00 1-216-049-11 1-216-049-11 1-216-049-11 RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 100 10K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1-216-073-00 1-216-049-11 1-216-049-11 1-216-033-00 1-216-049-11 METAL CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP 10K 1K 1K 220 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 1K 470 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1K 5% 1/10W QQ 376315150 892498299 1/10W 8-729-101-07 TRANSISTOR 2SB798-T1-DLDK 8-729-931-02 TRANSISTOR 2SC2413KT146-PQ < RESISTOR > R700 R701 R702 R703 R704 1-216-077-11 1-216-089-11 1-216-295-00 1-216-117-00 1-216-075-00 RES-CHIP RES-CHIP SHORT METAL CHIP METAL CHIP 15K 47K 0 680K 12K 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R781 R787 R788 R789 R790 R705 R706 R707 R710 R711 1-216-214-00 1-216-101-00 1-216-033-00 1-216-114-00 1-216-101-00 RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 4.7K 150K 220 510K 150K 5% 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/10W 1/10W R791 R795 R796 R797 R798 1-216-049-11 1-216-041-00 1-216-049-11 1-216-049-11 1-216-049-11 R712 R713 R714 R715 R716 1-216-095-00 1-216-089-11 1-216-089-11 1-216-101-00 1-216-097-11 METAL CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP 82K 47K 47K 150K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R799 1-216-049-11 RES-CHIP R718 R719 R720 1-216-041-00 METAL CHIP 1-216-041-00 METAL CHIP 1-216-041-00 METAL CHIP 470 470 470 5% 5% 5% 1/10W 1/10W 1/10W www . Remark < VIBRATOR > X701 1-781-462-21 VIBRATOR, CRYSTAL (16.9344MHz) ************************************************************* xiaoy u163. com – 113 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 < TRANSISTOR > 100K 100K 100K 100K 100K QQ QQ TEL 13942296513 1-216-025-11 RES-CHIP 100 1-410-997-22 INDUCTOR CHIP 2.2uH RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1/10W < COIL > L701 L702 Description 1-216-097-11 1-216-097-11 1-216-097-11 1-216-097-11 1-216-097-11 13942296513 13942296513 1-216-295-00 1-216-295-00 1-216-295-00 1-216-296-00 1-216-049-11 Part No. R721 R722 R723 R724 R725 TEL TEL JC702 JC704 JC705 JC706 JC707 Ref. No. http://www.xiaoyu163.com QQ 376315150 892498299 CD MOTOR DG Ref. No. Part No. * A-3322-538-A CD MOTOR BOARD, COMPLETE ************************** Description Remark < CAPACITOR > C801 C802 C803 C804 1-163-021-11 1-164-161-11 1-163-038-00 1-126-934-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.01uF 10% 0.0022uF 10% 0.1uF 220uF 20% 50V 100V 25V 16V < CONNECTOR > * CN801 1-785-677-11 PIN, CONNECTOR (PC BOARD) 11P < IC > 8-759-344-00 IC NJM2100E(TE2) 8-759-591-65 IC BA6892FP-E2 < JUMPER RESISTOR > 1-216-295-00 SHORT 0 0.1uF 100PF 100PF 12PF 12PF Remark C610 C611 C612 C613 C614 1-164-156-11 1-164-156-11 1-164-156-11 1-163-251-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 100PF 100PF C615 C616 C617 C619 C620 1-164-156-11 1-164-156-11 1-164-156-11 1-126-207-11 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 33uF 0.47uF C621 C622 C626 C627 C628 1-107-826-11 1-107-725-11 1-163-021-11 1-164-156-11 1-126-205-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.1uF 0.1uF 0.01uF 0.1uF 47uF 10% 10% 10% 20% 16V 16V 50V 25V 6.3V C629 C632 C633 C634 C635 1-126-205-11 1-126-603-11 1-126-603-11 1-162-970-11 1-126-205-11 ELECT CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP 47uF 4.7uF 4.7uF 0.01uF 47uF 20% 20% 20% 10% 20% 6.3V 35V 35V 25V 6.3V C637 C639 C640 C641 C642 1-126-603-11 1-124-779-00 1-126-603-11 1-163-021-11 1-126-205-11 ELECT CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP 4.7uF 10uF 4.7uF 0.01uF 47uF 20% 20% 20% 10% 20% 35V 16V 35V 50V 6.3V 5% 5% 5% 5% 25V 50V 50V 50V 50V 5% 5% 25V 25V 25V 50V 50V 20% 10% 25V 25V 25V 4V 16V < TRANSISTOR > QQ Q801 Q802 Q803 Q804 Q805 8-729-027-56 8-729-027-60 8-729-027-60 8-729-027-56 8-729-900-53 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC143TKA-T146 DTC144TKA-T146 DTC144TKA-T146 DTC143TKA-T146 DTC114EKA-T146 Q806 Q807 8-729-903-46 TRANSISTOR 2SB1132-T100-QR 8-729-027-46 TRANSISTOR DTC114YKA-T146 QQ 376315150 892498299 376315150 892498299 TEL 13942296513 < RESISTOR > R801 R802 R803 R804 R805 1-216-081-00 1-216-099-00 1-216-089-11 1-216-081-00 1-216-085-00 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 22K 120K 47K 22K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C644 C645 C646 C650 C651 1-164-156-11 1-164-156-11 1-162-919-11 1-162-966-11 1-162-966-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 22PF 5% 0.0022uF 10% 0.0022uF 10% 25V 25V 50V 50V 50V R806 R807 R808 R809 R810 1-216-065-11 1-216-073-00 1-216-097-11 1-216-073-00 1-216-089-11 RES-CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP 4.7K 10K 100K 10K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C655 C657 C659 C660 C662 1-162-970-11 1-162-970-11 1-163-021-11 1-126-205-11 1-163-038-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.01uF 0.01uF 0.01uF 47uF 0.1uF 10% 10% 10% 20% 25V 25V 50V 6.3V 25V R811 1-216-198-11 RES-CHIP 1K 5% 1/8W C663 C664 C665 C668 C669 1-162-915-11 1-126-206-11 1-126-206-11 1-164-156-11 1-164-360-11 CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 10PF 100uF 100uF 0.1uF 0.1uF 0.5PF 20% 20% 50V 6.3V 6.3V 25V 16V C670 C672 C673 C675 C676 1-126-205-11 1-162-970-11 1-162-912-11 1-162-927-11 1-162-927-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.01uF 7PF 100PF 100PF 20% 10% 0.5PF 5% 5% 6.3V 25V 50V 50V 50V C680 C681 C682 1-163-224-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP 1-163-038-00 CERAMIC CHIP 7PF 0.1uF 0.1uF 0.25PF 50V 25V 25V < SWITCH > S801 1-762-812-11 SWITCH, LEAF (LIMIT) ************************************************************* A-3322-531-A DG BOARD, COMPLETE ******************* * < CAPACITOR > C601 C602 C604 1-162-919-11 CERAMIC CHIP 1-162-919-11 CERAMIC CHIP 1-163-235-11 CERAMIC CHIP www . 22PF 22PF 22PF 5% 5% 5% 50V 50V 50V xiaoy u163. com – 114 – http://www.xiaoyu163.com 376315150 892498299 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP QQ Description 1-164-156-11 1-162-927-11 1-162-927-11 1-162-916-11 1-162-916-11 13942296513 13942296513 JC801 Part No. C605 C606 C607 C608 C609 TEL TEL IC801 IC802 Ref. No. http://www.xiaoyu163.com QQ 376315150 892498299 DG Ref. No. Description 1-162-964-11 1-162-964-11 1-162-927-11 1-162-927-11 1-163-038-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 100PF 100PF 0.1uF C689 C690 C691 C692 C693 1-164-156-11 1-163-259-11 1-162-964-11 1-162-964-11 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 220PF 0.001uF 0.001uF 0.001uF C694 C695 C696 C697 C699 1-162-964-11 1-162-964-11 1-163-021-11 1-162-970-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.01uF 0.01uF 0.01uF Remark Ref. No. FERRITE, EMI (SMD) SHORT 0 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) 5% 10% 10% 10% 25V 50V 50V 50V 50V FB631 FB632 FB633 FB634 FB636 1-500-445-21 1-500-445-21 1-469-185-11 1-469-185-11 1-500-445-21 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR FERRITE, EMI (SMD) 10% 10% 10% 10% 10% 50V 50V 50V 25V 25V FB637 FB638 FB639 FB640 FB641 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FB642 FB643 FB644 FB645 FB646 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FB647 FB648 FB649 FB650 FB651 1-500-445-21 1-216-295-00 1-500-445-21 1-216-821-11 1-216-825-11 FERRITE, EMI (SMD) SHORT 0 FERRITE, EMI (SMD) METAL CHIP 1K METAL CHIP 2.2K FB652 FB653 FB654 FB655 FB656 1-216-295-00 1-216-295-00 1-500-445-21 1-469-185-11 1-469-185-11 SHORT 0 SHORT 0 FERRITE, EMI (SMD) FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR FB657 FB660 FB661 FB662 FB663 1-469-185-11 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 FERRITE BEAD INDUCTOR FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FB664 FB665 FB666 FB671 FB672 1-500-445-21 1-500-445-21 1-216-815-11 1-500-445-21 1-500-445-21 FERRITE, EMI (SMD) FERRITE, EMI (SMD) METAL CHIP 330 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FB673 1-500-445-21 FERRITE, EMI (SMD) < CONNECTOR > * * * * CN601 CN602 CN603 CN604 CN605 1-793-115-21 1-793-116-21 1-580-055-21 1-785-370-21 1-784-687-41 CONNECTOR, FFC/FPC 21P CONNECTOR, FFC/FPC 23P PIN, CONNECTOR (SMD) 2P CONNECTOR, FFC/FPC 26P PIN, CONNECTOR (PC BOARD) 7P < DIODE > D602 D603 8-719-988-61 DIODE 1SS355TE-17 8-719-988-61 DIODE 1SS355TE-17 < FERRITE BEAD > TEL 13942296513 FB601 FB602 FB603 FB604 FB605 1-500-445-21 1-216-821-11 1-216-821-11 1-216-295-00 1-216-821-11 FERRITE, EMI (SMD) METAL CHIP 1K METAL CHIP 1K SHORT 0 METAL CHIP 1K FB606 FB607 FB608 FB609 FB610 1-216-295-00 1-500-445-21 1-216-821-11 1-216-821-11 1-412-985-11 SHORT 0 FERRITE, EMI (SMD) METAL CHIP 1K METAL CHIP 1K INDUCTOR 3.3uH FB611 FB612 FB613 FB614 FB615 1-500-445-21 1-469-185-11 1-500-445-21 1-500-445-21 1-500-445-21 FERRITE, EMI (SMD) FERRITE BEAD INDUCTOR FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FB616 FB617 FB618 FB619 FB620 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FB621 FB622 FB623 FB624 FB625 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) 5% 5% . 5% 5% 1/16W 1/16W QQ 376315150 892498299 1/16W 1/16W 5% 1/16W 5% 5% 1/16W 1/16W < FILTER > www Remark * * * * FL601 FL602 FL603 FL604 FL605 1-239-901-21 1-239-901-21 1-239-899-21 1-239-899-21 1-239-899-21 FILTER, CHIP EMI FILTER, CHIP EMI FILTER, CHIP EMI FILTER, CHIP EMI FILTER, CHIP EMI FL606 FL607 FL608 FL611 FL612 1-239-899-21 1-125-971-21 1-125-971-21 1-125-971-21 1-125-971-21 FILTER, CHIP EMI FILTER, 3 TERMINAL NOISE FILTER, 3 TERMINAL NOISE FILTER, 3 TERMINAL NOISE FILTER, 3 TERMINAL NOISE xiaoy u163. com – 115 – http://www.xiaoyu163.com 5% 1/16W 376315150 892498299 376315150 892498299 1-500-445-21 1-216-295-00 1-500-445-21 1-500-445-21 1-469-125-21 QQ QQ Description FB626 FB627 FB628 FB629 FB630 13942296513 13942296513 Part No. 50V 50V 50V 50V 25V 10% 10% 5% 5% TEL TEL Part No. C683 C684 C685 C686 C687 http://www.xiaoyu163.com QQ 376315150 892498299 DG Ref. No. Part No. * FL619 * FL620 1-125-971-21 FILTER, 3 TERMINAL NOISE 1-125-971-21 FILTER, 3 TERMINAL NOISE Description Remark < IC > IC601 IC602 IC603 IC604 IC605 8-759-670-32 8-759-040-83 8-759-561-36 8-759-243-19 8-759-591-61 IC IC IC IC IC RU8X13MF-0102 BA6287F-T1 PCM3003E/T2 TC7SU04F-TE85L TC7WHU04FU(TE12R) IC606 8-759-447-77 IC TC7WH74FU(TE12R) < JUMPER RESISTOR > JC607 JC608 JC609 JC610 JC611 1-216-295-00 1-216-295-00 1-216-821-11 1-216-821-11 1-216-821-11 SHORT SHORT METAL CHIP METAL CHIP METAL CHIP 0 0 1K 1K 1K JC612 JC613 JC614 JC615 JC616 1-216-821-11 1-216-295-00 1-216-049-11 1-216-295-00 1-216-295-00 METAL CHIP SHORT RES-CHIP SHORT SHORT 1K 0 1K 0 0 JC617 JC618 JC619 JC620 JC621 1-216-295-00 1-216-295-00 1-500-445-21 1-216-295-00 1-216-864-11 SHORT 0 SHORT 0 FERRITE, EMI (SMD) SHORT 0 METAL CHIP 0 JC622 JC623 JC626 JC627 JC631 1-216-296-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-864-11 SHORT SHORT SHORT SHORT METAL CHIP JC632 JC634 JC635 JC639 JC641 1-216-295-00 1-216-295-00 1-216-295-00 1-500-445-21 1-216-295-00 SHORT 0 SHORT 0 SHORT 0 FERRITE, EMI (SMD) SHORT 0 JC651 JC652 1-216-295-00 SHORT 1-412-989-11 INDUCTOR 5% 1/10W 5% 1/10W Remark L612 L613 L614 L615 L616 1-414-521-21 1-414-398-11 1-414-398-11 1-500-445-21 1-500-445-21 INDUCTOR CHIP 10uH INDUCTOR 10uH INDUCTOR 10uH FERRITE, EMI (SMD) FERRITE, EMI (SMD) L617 L618 L619 L620 L621 1-414-766-22 1-500-445-21 1-414-398-11 1-414-398-11 1-414-521-21 FERRITE BEAD INDUCTOR FERRITE, EMI (SMD) INDUCTOR 10uH INDUCTOR 10uH INDUCTOR CHIP 10uH L622 1-414-521-21 INDUCTOR CHIP 10uH < TRANSISTOR > 5% 5% 5% 1/16W 1/16W 1/16W 5% 1/16W 5% 1/10W 0 0 0 0 0 0 6.8uH < COIL > L601 L602 L603 L604 L605 1-414-521-21 1-414-398-11 1-414-398-11 1-414-398-11 1-414-398-11 INDUCTOR CHIP INDUCTOR INDUCTOR INDUCTOR INDUCTOR L606 1-414-398-11 INDUCTOR www . 10uH 10uH 10uH 10uH 10uH 10uH 5% 8-729-402-84 8-729-402-84 8-729-027-46 8-729-031-43 8-729-101-07 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR XN4601-TX XN4601-TX DTC114YKA-T146 IMD9A-T108 2SB798-T1-DLDK Q616 Q617 Q620 8-729-027-46 TRANSISTOR DTC114YKA-T146 8-729-019-72 TRANSISTOR 2SB1260T100 8-729-046-16 TRANSISTOR UMG5NTR QQ 376315150 892498299 TEL 13942296513 5% Q603 Q604 Q610 Q611 Q612 < RESISTOR > 1/16W 1/16W R601 R602 R603 R604 R605 1-216-821-11 1-216-049-11 1-216-821-11 1-500-329-11 1-216-073-00 METAL CHIP 1K RES-CHIP 1K METAL CHIP 1K FERRITE BEAD INDUCTOR METAL CHIP 10K 5% 5% 5% 1/16W 1/10W 1/16W 5% 1/10W R606 R607 R608 R609 R610 1-216-073-00 1-216-073-00 1-216-833-11 1-216-097-11 1-216-097-11 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 10K 10K 10K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/16W 1/10W 1/10W R611 R612 R613 R614 R615 1-216-845-11 1-216-097-11 1-216-833-11 1-216-857-11 1-216-833-11 METAL CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP 100K 100K 10K 1M 10K 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/16W 1/16W R616 R617 R618 R619 R620 1-216-845-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-851-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 100 100K 330K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R621 R622 R623 R624 R625 1-216-073-00 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 10K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W xiaoy u163. com – 116 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1K 0 1K 0 0 INDUCTOR 10uH INDUCTOR 10uH INDUCTOR 10uH INDUCTOR 10uH COIL, COMMON MODE CHOKE QQ QQ RES-CHIP SHORT RES-CHIP SHORT SHORT Description 1-414-398-11 1-414-398-11 1-414-398-11 1-414-398-11 1-416-107-21 13942296513 13942296513 1-216-049-11 1-216-295-00 1-216-049-11 1-216-295-00 1-216-296-00 Part No. L607 L608 L609 L610 L611 TEL TEL JC601 JC602 JC603 JC605 JC606 Ref. No. http://www.xiaoyu163.com QQ 376315150 892498299 DG Ref. No. Part No. Description FL Part No. Description Remark Ref. No. R626 R627 R628 R629 R630 1-216-073-00 1-216-089-11 1-216-841-11 1-216-833-11 1-216-833-11 METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 10K 47K 47K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/16W 1/16W 1/16W X602 1-781-183-11 VIBRATOR, CRYSTAL (32.768kHz) X603 1-760-173-11 VIBRATOR, CRYSTAL (22.5792MHz) ************************************************************* Remark R631 R632 R633 R634 R636 1-216-821-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-851-11 METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP 1K 1K 10K 10K 330K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R637 R638 R639 R640 R641 1-216-109-00 1-216-841-11 1-216-847-11 1-216-821-11 1-216-843-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330K 47K 150K 1K 68K 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W R643 R644 R646 R647 R648 1-216-809-11 1-216-833-11 1-216-041-00 1-216-089-11 1-216-833-11 METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 100 10K 470 47K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W 1/16W R649 R650 R651 R652 R653 1-216-835-11 1-216-833-11 1-216-835-11 1-500-329-11 1-216-073-00 METAL CHIP 15K RES-CHIP 10K METAL CHIP 15K FERRITE BEAD INDUCTOR METAL CHIP 10K 5% 5% 5% 1/16W 1/16W 1/16W 5% 1/10W R654 R655 R656 R657 R658 1-216-833-11 1-216-073-00 1-216-833-11 1-216-238-11 1-216-853-11 RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP 10K 10K 10K 47K 470K 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/8W 1/16W R659 R660 R661 R662 R663 1-216-817-11 1-216-841-11 1-216-857-11 1-216-037-00 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 47K 1M 330 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/16W R664 R665 R666 R667 R668 1-216-821-11 1-216-073-00 1-500-329-11 1-500-329-11 1-216-815-11 METAL CHIP 1K METAL CHIP 10K FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR METAL CHIP 330 5% 5% 1/16W 1/10W 5% 1/16W R669 R670 R671 R672 R674 1-216-857-11 1-216-841-11 1-216-821-11 1-216-821-11 1-216-857-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1M 47K 1K 1K 1M 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R691 R692 R693 R694 R695 1-216-821-11 1-216-025-11 1-216-025-11 1-216-821-11 1-216-821-11 METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP 1K 100 100 1K 1K 5% 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/16W 1/16W A-3322-528-A FL BOARD, COMPLETE ******************* * 3-039-978-01 HOLDER (FL) 3-042-764-01 SHEET (FL), ADHESIVE 3-846-312-01 SPACER < CAPACITOR > ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 10uF 0.01uF 470PF 47uF 1uF 20% 10% 5% 20% 10% 50V 50V 50V 10V 16V C606 C607 C608 C609 C614 1-163-021-11 1-163-009-11 1-163-243-11 1-163-251-11 1-163-259-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.001uF 47PF 100PF 220PF 10% 10% 5% 5% 5% 50V 50V 50V 50V 50V C621 C622 C623 C624 C625 1-163-259-11 1-164-005-11 1-164-005-11 1-164-005-11 1-164-005-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220PF 0.47uF 0.47uF 0.47uF 0.47uF 5% 50V 25V 25V 25V 25V CN601 < FILTER > FL401 < VIBRATOR > 1-517-916-11 INDICATOR TUBE, FLUORESCENT < IC > IC601 X601 1-695-371-31 CONNECTOR, FFC/FPC 10P 8-759-648-76 IC MSM9202-09GS-KDR1 < TRANSISTOR > Q612 Q613 8-729-027-44 TRANSISTOR DTC114TKA-T146 8-729-027-44 TRANSISTOR DTC114TKA-T146 < RESISTOR > R601 R602 R605 R606 R609 1-216-073-00 1-216-017-11 1-216-073-00 1-216-017-11 1-216-041-00 . 10K 47 10K 47 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R610 1-216-049-11 RES-CHIP 1K 5% 1/10W R611 1-216-049-11 RES-CHIP 1K 5% 1/10W R612 1-216-041-00 METAL CHIP 470 5% 1/10W R613 1-216-049-11 RES-CHIP 1K 5% 1/10W ************************************************************* 1-767-179-21 VIBRATOR, CERAMIC (12MHz) www METAL CHIP RES-CHIP METAL CHIP RES-CHIP METAL CHIP xiaoy u163. com – 117 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 QQ 376315150 892498299 QQ QQ < CONNECTOR > 13942296513 13942296513 1-126-964-11 1-163-021-11 1-163-133-00 1-104-664-11 1-107-682-11 TEL TEL TEL 13942296513 C601 C602 C603 C604 C605 http://www.xiaoyu163.com QQ 376315150 892498299 JACK KEY LED Ref. No. Part No. * 1-675-219-21 JACK BOARD *********** Description Remark < CONNECTOR > * CN306 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 < FERRITE BEAD > LED LED LED LED LED SLA-362MT-T31XFG (DISPLAY) SLA-362MT-T31XFG (4/GHI) SLR-332VRT32 (abc) SLR-332VRT32 (ABC) SLA-362MT-T31XFG (1) FB101 FB102 FB201 FB202 FB301 1-216-295-00 1-469-152-11 1-216-295-00 1-469-152-11 1-216-295-00 FB302 1-469-152-11 FERRITE, EMI (SMD) D611 D612 D613 D614 D615 8-719-078-08 8-719-078-08 8-719-078-08 8-719-078-08 8-719-078-08 LED LED LED LED LED SLA-362MT-T31XFG (1) SLA-362MT-T31XFG (2/ABC) SLA-362MT-T31XFG (3/DEF) SLA-362MT-T31XFG (DISPLAY) SLA-362MT-T31XFG (4/GHI) D616 D617 D618 D619 D620 8-719-078-08 8-719-078-08 8-719-078-08 8-719-078-08 8-719-078-08 LED LED LED LED LED SLA-362MT-T31XFG (5/JKL) SLA-362MT-T31XFG (6/MNO) SLA-362MT-T31XFG (7/PQRS) SLA-362MT-T31XFG (7/PQRS) SLA-362MT-T31XFG (8/TUV) SHORT 0 FERRITE, EMI (SMD) SHORT 0 FERRITE, EMI (SMD) SHORT 0 D621 D622 D623 D624 D625 8-719-078-08 8-719-078-08 8-719-078-08 8-719-078-08 8-719-078-08 LED LED LED LED LED SLA-362MT-T31XFG (9/WXYZ) SLA-362MT-T31XFG (SYMBOL) SLA-362MT-T31XFG (SYMBOL) SLA-362MT-T31XFG (0/10) SLA-362MT-T31XFG (>10) < IC > < JACK > J301 J302 Remark 13942296513 13942296513 Description 8-719-078-08 8-719-078-08 8-719-077-79 8-719-077-79 8-719-078-08 TEL TEL Part No. D606 D607 D608 D609 D610 1-573-455-11 PLUG, CONNECTOR 4P < DIODE > D301 D302 D303 D304 Ref. No. IC602 1-779-050-11 JACK (i) 1-779-050-11 JACK (LINE IN) 8-749-016-97 IC NJL62H400A < JUMPER RESISTOR > < RESISTOR > < CONNECTOR > * CN603 1-695-333-41 PIN, CONNECTOR (PC BOARD) 10P ************************************************************* A-3322-525-A LED BOARD, COMPLETE ******************** * SHORT SHORT SHORT SHORT 0 0 0 0 QQ 376315150 892498299 < TRANSISTOR > 1-675-223-21 KEY BOARD ********** * 1-216-295-00 1-216-296-00 1-216-295-00 1-216-295-00 Q603 Q604 Q606 Q607 Q608 8-729-027-58 8-729-901-88 8-729-027-58 8-729-027-58 8-729-120-28 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC143ZKA-T146 2SC2411K-T-146-CR DTC143ZKA-T146 DTC143ZKA-T146 2SC2412K-T-146-QR Q609 Q610 Q611 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR < CAPACITOR > < RESISTOR > C610 C611 1-163-021-11 CERAMIC CHIP 1-126-794-11 ELECT 0.01uF 4.7uF 10% 20% 50V 25V < CONNECTOR > * CN602 1-695-374-31 PIN, CONNECTOR (PC BOARD) 13P < DIODE > D601 D602 D603 D604 D605 8-719-077-79 8-719-078-08 8-719-078-08 8-719-078-08 8-719-078-08 LED LED LED LED LED www SLR-332VRT32 (HIGH SPEED) SLA-362MT-T31XFG (DELETE/CLOCK) SLA-362MT-T31XFG (INSERT/TIMER) SLA-362MT-T31XFG (NO/CANCELE) SLA-362MT-T31XFG (YES/ENTER) . R603 R614 R615 R617 R620 1-216-025-11 1-216-085-00 1-216-033-00 1-216-025-11 1-216-025-11 RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 100 33K 220 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R622 R624 R626 R628 R631 1-216-051-00 1-216-033-00 1-216-033-00 1-216-025-11 1-216-174-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 1.2K 220 220 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/8W R633 R636 1-216-025-11 RES-CHIP 1-216-025-11 RES-CHIP 100 100 5% 5% 1/10W 1/10W xiaoy u163. com – 118 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 TEL 13942296513 JC601 JC602 JC603 JC604 QQ QQ R103 1-216-033-00 METAL CHIP 220 5% 1/10W R203 1-216-033-00 METAL CHIP 220 5% 1/10W ************************************************************* http://www.xiaoyu163.com QQ 376315150 892498299 LED Ref. No. Remark Ref. No. MAIN 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C117 C118 C119 C126 C127 1-126-963-11 1-126-961-11 1-126-960-11 1-126-960-11 1-163-009-11 ELECT ELECT ELECT ELECT CERAMIC CHIP 4.7uF 2.2uF 1uF 1uF 0.001uF 20% 20% 20% 20% 10% 50V 50V 50V 50V 50V Remark R649 R650 R651 R666 R667 1-216-048-00 1-216-056-00 1-216-061-00 1-216-025-11 1-216-025-11 METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 910 2K 3.3K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C128 C201 C202 C203 C204 1-163-251-11 1-126-767-11 1-126-963-11 1-126-963-11 1-163-251-11 CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP 100PF 1000uF 4.7uF 4.7uF 100PF 5% 20% 20% 20% 5% 50V 16V 50V 50V 50V R668 R670 R671 R672 R673 1-216-025-11 1-216-025-11 1-216-025-11 1-216-025-11 1-216-025-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C205 C206 C207 C208 C209 1-163-021-11 1-136-165-00 1-136-165-00 1-126-960-11 1-126-964-11 CERAMIC CHIP MYLAR MYLAR ELECT ELECT 0.01uF 0.1uF 0.1uF 1uF 10uF 10% 5% 5% 20% 20% 50V 50V 50V 50V 50V R674 R675 R676 R677 1-216-025-11 1-216-025-11 1-216-025-11 1-216-025-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100 100 100 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W C210 C211 C212 C213 C214 1-126-961-11 1-126-961-11 1-126-961-11 1-126-961-11 1-136-157-00 ELECT ELECT ELECT ELECT MYLAR 2.2uF 2.2uF 2.2uF 2.2uF 0.022uF 20% 20% 20% 20% 5% 50V 50V 50V 50V 50V C215 C216 C217 C218 C219 1-136-173-00 1-136-153-00 1-126-963-11 1-126-961-11 1-126-960-11 MYLAR FILM ELECT ELECT ELECT 0.47uF 0.01uF 4.7uF 2.2uF 1uF 5% 5% 20% 20% 20% 50V 50V 50V 50V 50V C226 C227 C228 C301 C302 1-126-960-11 1-163-009-11 1-163-251-11 1-104-665-11 1-126-963-11 ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT 1uF 0.001uF 100PF 100uF 4.7uF 20% 10% 5% 20% 20% 50V 50V 50V 10V 50V C303 C306 C307 C308 C309 1-115-877-11 1-126-964-11 1-163-009-11 1-104-665-11 1-126-934-11 ELECT(BLOCK) ELECT CERAMIC CHIP ELECT ELECT 4700uF 10uF 0.001uF 100uF 220uF 20% 20% 10% 20% 20% 25V 50V 50V 10V 10V C310 C311 C312 C313 C314 1-104-665-11 1-104-665-11 1-104-665-11 1-126-964-11 1-163-021-11 ELECT ELECT ELECT ELECT CERAMIC CHIP 100uF 100uF 100uF 10uF 0.01uF 20% 20% 20% 20% 10% 10V 10V 10V 50V 50V C315 C316 C317 C318 C319 1-163-021-11 1-104-665-11 1-107-725-11 1-126-964-11 1-126-960-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT 0.01uF 100uF 0.1uF 10uF 1uF 10% 20% 10% 20% 20% 50V 10V 16V 50V 50V C320 C321 C322 C323 C324 1-163-009-11 1-163-009-11 1-126-964-11 1-104-665-11 1-104-665-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 0.001uF 0.001uF 10uF 100uF 100uF 10% 10% 20% 20% 20% 50V 50V 50V 10V 10V C326 C401 C402 1-126-964-11 ELECT 1-163-237-11 CERAMIC CHIP 1-163-104-00 CERAMIC CHIP 10uF 27PF 30PF 20% 5% 5% 50V 50V 50V < SWITCH > S601 S602 S603 S604 S605 1-762-798-11 1-762-798-11 1-762-798-11 1-762-798-11 SWITCH, KEY BOARD (OPERATE) SWITCH, KEY BOARD (SLEEP) SWITCH, KEY BOARD (STANDBY) SWITCH, KEY BOARD (AUTO PRESET/RDS/ SHUF/PGM) 1-762-798-11 SWITCH, KEY BOARD (MONO/ST/REPEAT) QQ 376315150 892498299 TEL 13942296513 S606 1-762-798-11 SWITCH, KEY BOARD (EDIT) ************************************************************* A-3322-530-A MAIN BOARD, COMPLETE ********************* * 3-039-961-01 SPRING (IC) 3-831-441-99 CUSHION (A) 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S < CAPACITOR > C101 C102 C103 C104 C105 1-126-767-11 1-126-963-11 1-126-963-11 1-163-251-11 1-163-021-11 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP 1000uF 4.7uF 4.7uF 100PF 0.01uF 20% 20% 20% 5% 10% 16V 50V 50V 50V 50V C106 C107 C108 C109 C110 1-136-165-00 1-136-165-00 1-126-960-11 1-126-964-11 1-126-961-11 MYLAR MYLAR ELECT ELECT ELECT 0.1uF 0.1uF 1uF 10uF 2.2uF 5% 5% 20% 20% 20% 50V 50V 50V 50V 50V C111 C112 C113 C114 C115 1-126-961-11 1-126-961-11 1-126-961-11 1-136-157-00 1-136-173-00 ELECT ELECT ELECT MYLAR MYLAR 2.2uF 2.2uF 2.2uF 0.022uF 0.47uF 20% 20% 20% 5% 5% 50V 50V 50V 50V 50V C116 1-136-153-00 FILM 0.01uF 5% 50V www . xiaoy u163. com – 119 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 Description 100 100 100 100 680 QQ QQ Part No. RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 13942296513 13942296513 Description 1-216-025-11 1-216-025-11 1-216-025-11 1-216-025-11 1-216-045-00 TEL TEL Part No. R638 R641 R643 R646 R648 http://www.xiaoyu163.com QQ 376315150 892498299 MAIN Ref. No. CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 33PF 33PF 0.001uF 0.001uF Remark 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C408 C409 C410 C411 C412 1-163-235-11 1-163-234-11 1-107-725-11 1-104-665-11 1-164-346-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 22PF 20PF 0.1uF 100uF 1uF C413 C414 C416 C417 C418 1-104-664-11 1-126-964-11 1-126-919-11 1-163-009-11 1-164-346-11 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP C419 C420 C421 C422 C423 1-163-021-11 1-126-933-11 1-107-725-11 1-126-925-11 1-163-021-11 C424 C425 C426 C428 C430 5% 5% 10% 20% 50V 50V 16V 10V 16V C464 C465 C466 C468 C469 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V 47uF 10uF 6800uF 0.001uF 1uF 20% 20% 20% 10% 10V 50V 6.3V 50V 16V C470 C471 C472 C473 C474 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP 0.01uF 100uF 0.1uF 470uF 0.01uF 10% 20% 10% 20% 10% 50V 16V 16V 10V 50V C475 C477 C478 C479 C480 1-163-009-11 1-163-251-11 1-163-243-11 1-163-009-11 1-163-021-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 100PF 47PF 0.001uF 0.01uF 10% 5% 5% 10% 10% 50V 50V 50V 50V 50V 1-163-021-11 1-126-934-11 1-163-021-11 1-104-664-11 1-163-021-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP 0.01uF 220uF 0.01uF 47uF 0.01uF 10% 20% 10% 20% 10% 50V 10V 50V 10V 50V C481 C482 C483 C484 C485 1-126-964-11 1-126-964-11 1-163-009-11 1-163-009-11 1-163-009-11 ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 0.001uF 0.001uF 0.001uF 20% 20% 10% 10% 10% 50V 50V 50V 50V 50V C431 C432 C433 C434 C435 1-126-934-11 1-163-021-11 1-163-021-11 1-126-964-11 1-163-021-11 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 220uF 0.01uF 0.01uF 10uF 0.01uF 20% 10% 10% 20% 10% 10V 50V 50V 50V 50V C486 C487 C488 C489 C490 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C436 C437 C438 C439 C440 1-163-021-11 1-126-964-11 1-163-021-11 1-126-968-11 1-126-960-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT 0.01uF 10uF 0.01uF 100uF 1uF 10% 20% 10% 20% 20% 50V 50V 50V 50V 50V C491 C492 C493 C494 C495 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C441 C442 C443 C444 C445 1-126-960-11 1-163-021-11 1-126-937-11 1-163-009-11 1-164-161-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 1uF 0.01uF 4700uF 0.001uF 0.0022uF 20% 10% 20% 10% 10% 50V 50V 16V 50V 100V C496 C497 C498 C499 C500 1-163-009-11 1-163-009-11 1-163-251-11 1-163-251-11 1-163-251-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 100PF 100PF 100PF 10% 10% 5% 5% 5% 50V 50V 50V 50V 50V C446 C447 C448 C449 C450 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C502 C503 C504 C505 C506 1-163-009-11 1-163-009-11 1-163-009-11 1-163-243-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 47PF 0.001uF 10% 10% 10% 5% 10% 50V 50V 50V 50V 50V C451 C452 C453 C454 C455 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C507 C509 C510 C512 C513 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C456 C457 C458 1-163-009-11 CERAMIC CHIP 1-163-009-11 CERAMIC CHIP 1-163-009-11 CERAMIC CHIP 0.001uF 0.001uF 0.001uF 10% 10% 10% 50V 50V 50V C514 C515 C516 1-163-009-11 CERAMIC CHIP 1-163-021-11 CERAMIC CHIP 1-163-021-11 CERAMIC CHIP 0.001uF 0.01uF 0.01uF 10% 10% 10% 50V 50V 50V TEL 13942296513 www . Remark QQ 376315150 892498299 xiaoy u163. com – 120 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 Description C459 C460 C461 C462 C463 5% 5% 10% 10% Ref. No. QQ QQ Part No. 16V 50V 50V 50V 50V 13942296513 13942296513 Description 1-164-346-11 1-163-239-11 1-163-239-11 1-163-009-11 1-163-009-11 TEL TEL Part No. C403 C404 C405 C406 C407 http://www.xiaoyu163.com QQ 376315150 892498299 MAIN Ref. No. CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 2.2uF 22PF 330PF 10% 10% 20% 5% 5% 50V 50V 50V 50V 50V Remark C522 C523 C524 C525 C526 1-163-233-11 1-128-551-11 1-163-021-11 1-163-021-11 1-128-551-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT 18PF 22uF 0.01uF 0.01uF 22uF 5% 20% 10% 10% 20% 50V 25V 50V 50V 25V C527 C528 C529 C530 C531 1-163-135-00 1-104-665-11 1-163-021-11 1-163-021-11 1-126-933-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT 560PF 100uF 0.01uF 0.01uF 100uF 5% 20% 10% 10% 20% 50V 10V 50V 50V 16V C532 C533 C534 C535 C536 1-126-933-11 1-163-021-11 1-163-009-11 1-163-009-11 1-163-009-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100uF 0.01uF 0.001uF 0.001uF 0.001uF 20% 10% 10% 10% 10% 16V 50V 50V 50V 50V C537 C538 C539 C540 C541 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V 1-564-778-11 1-785-656-11 1-564-778-11 1-785-662-11 1-568-468-11 PLUG, CONNECTOR (2.5mm) 4P PIN, CONNECTOR (PC BOARD) 4P PLUG, CONNECTOR (2.5mm) 4P PIN, CONNECTOR (PC BOARD) 10P PIN, CONNECTOR (PC BOARD) 18P CN404 * CN405 CN406 * CN407 * CN408 1-568-931-11 1-695-333-41 1-695-336-31 1-695-333-41 1-785-664-11 PIN, CONNECTOR (PC BOARD) 26P PIN, CONNECTOR (PC BOARD) 10P PIN, CONNECTOR (PC BOARD) 13P PIN, CONNECTOR (PC BOARD) 10P PIN, CONNECTOR (PC BOARD) 12P * CN409 * CN410 CN412 1-785-655-11 PIN, CONNECTOR (PC BOARD) 3P 1-785-654-11 PIN, CONNECTOR (PC BOARD) 2P 1-566-690-11 PLUG, CONNECTOR (2.5mm) 2P Description Remark < FERRITE BEAD > FB401 FB402 FB403 FB404 FB405 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 FB406 FB407 FB408 FB409 FB410 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 FB411 FB412 FB413 FB414 FB415 1-216-295-00 1-469-185-11 1-469-185-11 1-216-295-00 1-216-295-00 SHORT 0 FERRITE BEAD INDUCTOR FERRITE BEAD INDUCTOR SHORT 0 SHORT 0 FB416 FB417 FB418 FB419 FB420 1-216-295-00 1-216-295-00 1-216-296-00 1-216-296-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 FB421 FB422 FB423 FB424 FB425 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 QQ 376315150 892498299 FB426 FB427 FB428 FB429 FB430 1-216-295-00 1-216-295-00 1-216-073-00 1-216-295-00 1-216-073-00 SHORT SHORT METAL CHIP SHORT METAL CHIP FB431 FB432 1-216-295-00 SHORT 1-216-295-00 SHORT 0 0 10K 0 10K 0 0 < IC > IC301 IC302 IC303 IC305 IC401 8-759-543-56 8-759-652-74 8-759-100-96 8-759-636-55 8-752-914-58 IC IC IC IC IC LA4601N M62443FPD61Q NJM4558M-TE2 M5218AFP-T1 CXP740096-043Q IC402 IC403 IC404 IC405 IC411 8-759-486-73 8-759-649-23 8-759-450-47 8-759-557-36 8-759-486-73 IC IC IC IC IC XC62FP3302PR XC61CN2802PR BA05T BU1924F-E2 XC62FP3302PR < DIODE > D301 D303 D304 D401 D402 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE DIODE 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 D403 D404 D405 D406 D408 8-719-056-84 8-719-056-85 8-719-056-82 8-719-977-81 8-719-056-97 DIODE DIODE DIODE DIODE DIODE UDZ-TE-17-7.5B UDZ-TE-17-8.2B UDZ-TE-17-6.2B UDZ-TE-17-33B UDZ-TE-17-27B < JUMPER RESISTOR > www . JC101 JC102 JC103 JC104 JC105 1-216-296-00 1-216-295-00 1-216-295-00 1-216-296-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT xiaoy u163. com – 121 – http://www.xiaoyu163.com 0 0 0 0 0 5% 1/10W 5% 1/10W 376315150 892498299 376315150 892498299 TEL 13942296513 CN301 CN303 CN401 CN402 CN403 * * * * * Part No. QQ QQ < CONNECTOR > Ref. No. 13942296513 13942296513 Description 1-163-021-11 1-163-021-11 1-126-961-11 1-163-235-11 1-163-263-11 TEL TEL Part No. C517 C518 C519 C520 C521 http://www.xiaoyu163.com QQ 376315150 892498299 MAIN Ref. No. JC106 JC107 JC108 JC109 JC113 Part No. Description 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT Remark 1-216-017-11 RES-CHIP 47 5% 1/10W < TRANSISTOR > Remark Q106 Q111 Q201 Q202 Q203 8-729-920-31 8-729-920-31 8-729-920-31 8-729-120-28 8-729-027-46 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC343TK-T-146 DTC343TK-T-146 DTC343TK-T-146 2SC2412K-T-146-QR DTC114YKA-T146 Q204 Q205 Q206 Q211 Q301 8-729-920-31 8-729-120-28 8-729-920-31 8-729-920-31 8-729-027-24 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC343TK-T-146 2SC2412K-T-146-QR DTC343TK-T-146 DTC343TK-T-146 DTA114TKA-T146 Q304 Q305 Q306 Q307 Q308 8-729-900-53 8-729-027-46 8-729-027-23 8-729-900-53 8-729-120-28 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114EKA-T146 DTC114YKA-T146 DTA114EKA-T146 DTC114EKA-T146 2SC2412K-T-146-QR Q309 Q310 Q311 Q312 Q313 8-729-027-23 8-729-027-26 8-729-027-24 8-729-027-24 8-729-027-26 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTA114EKA-T146 DTA114YKA-T146 DTA114TKA-T146 DTA114TKA-T146 DTA114YKA-T146 Q401 Q402 Q403 Q405 Q406 8-729-903-10 8-729-018-99 8-729-021-82 8-729-021-82 8-729-903-46 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR FMW1-T-148 2SD2394-F 2SD2396K 2SD2396K 2SB1132-T100-QR Q407 Q408 Q409 Q411 Q412 8-729-027-26 8-729-027-46 8-729-904-86 8-729-027-26 8-729-027-46 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTA114YKA-T146 DTC114YKA-T146 2SB1197K-T-146-Q DTA114YKA-T146 DTC114YKA-T146 Q415 Q416 Q419 Q420 Q421 8-729-027-29 8-729-027-46 8-729-012-83 8-729-012-83 8-729-027-26 TRANSISTOR DTA123JKA-T146 TRANSISTOR DTC114YKA-T146 FET 2SK679A-T FET 2SK679A-T TRANSISTOR DTA114YKA-T146 Q422 Q430 Q431 8-729-027-46 TRANSISTOR DTC114YKA-T146 8-729-027-26 TRANSISTOR DTA114YKA-T146 8-729-027-46 TRANSISTOR DTC114YKA-T146 TEL 13942296513 RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP 1K 3.3K 100 1K 1.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R106 R107 R108 R109 R110 1-216-111-00 1-216-121-11 1-216-079-00 1-216-073-00 1-216-049-11 METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP 390K 1M 18K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R111 R112 R113 R114 R115 1-216-077-11 1-216-073-00 1-216-689-11 1-216-089-11 1-216-079-00 RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 15K 10K 39K 47K 18K 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R116 R117 R118 R119 R120 1-216-113-00 1-216-077-11 1-216-057-00 1-216-047-11 1-216-061-00 METAL CHIP RES-CHIP METAL CHIP RES-CHIP METAL CHIP 470K 15K 2.2K 820 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R122 R123 R124 R125 R201 1-216-198-11 1-216-077-11 1-216-049-11 1-216-089-11 1-216-049-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 15K 1K 47K 1K 5% 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/10W 1/10W R202 R203 R204 R205 R206 1-216-061-00 1-216-025-11 1-216-049-11 1-216-052-00 1-216-111-00 METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP 3.3K 100 1K 1.3K 390K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R207 R208 R209 R210 R211 1-216-121-11 1-216-079-00 1-216-073-00 1-216-049-11 1-216-077-11 RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 1M 18K 10K 1K 15K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R212 R213 R214 R215 R216 1-216-073-00 1-216-689-11 1-216-089-11 1-216-079-00 1-216-113-00 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 10K 39K 47K 18K 470K 5% 0.5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R217 R218 R219 R220 R222 1-216-077-11 1-216-057-00 1-216-047-11 1-216-061-00 1-216-049-11 RES-CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP 15K 2.2K 820 3.3K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R223 R224 R225 R302 R303 1-216-077-11 1-216-049-11 1-216-089-11 1-216-073-00 1-216-073-00 RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP 15K 1K 47K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W QQ 376315150 892498299 xiaoy u163. com – 122 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 DTC343TK-T-146 2SC2412K-T-146-QR DTC114YKA-T146 DTC343TK-T-146 2SC2412K-T-146-QR 1-216-049-11 1-216-061-00 1-216-025-11 1-216-049-11 1-216-052-00 QQ QQ TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR R101 R102 R103 R104 R105 13942296513 13942296513 8-729-920-31 8-729-120-28 8-729-027-46 8-729-920-31 8-729-120-28 . Description TEL TEL Q101 Q102 Q103 Q104 Q105 www Part No. 8-729-027-26 TRANSISTOR DTA114YKA-T146 < RESISTOR > < COIL > L401 Ref. No. Q432 0 0 0 0 0 http://www.xiaoyu163.com QQ 376315150 892498299 MAIN Ref. No. 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/8W Remark R435 R436 R437 R438 R439 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-113-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 1K 1K 1K 1K 470K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R310 R311 R312 R313 R314 1-216-049-11 1-216-049-11 1-216-065-11 1-216-073-00 1-216-073-00 RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP 1K 1K 4.7K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R440 R441 R442 R443 R444 1-216-049-11 1-216-049-11 1-216-085-00 1-216-085-00 1-216-085-00 RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 33K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R315 R316 R317 R318 R319 1-216-073-00 1-216-113-00 1-216-049-11 1-216-121-11 1-216-049-11 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 10K 470K 1K 1M 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R445 R446 R447 R448 R449 1-216-085-00 1-216-085-00 1-216-065-11 1-216-049-11 1-216-049-11 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 33K 33K 4.7K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R320 R321 R322 R323 R324 1-216-049-11 1-216-097-11 1-216-073-00 1-216-041-00 1-216-049-11 RES-CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP 1K 100K 10K 470 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R450 R451 R452 R453 R454 1-216-049-11 1-216-049-11 1-216-049-11 1-216-065-11 1-216-113-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 1K 1K 1K 4.7K 470K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R327 R328 R329 R401 R402 1-216-073-00 1-216-073-00 1-216-025-11 1-216-222-00 1-216-198-11 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 10K 10K 100 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/8W 1/8W R455 R456 R457 R458 R459 1-216-041-00 1-216-041-00 1-216-049-11 1-216-049-11 1-216-069-00 METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP 470 470 1K 1K 6.8K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R403 R404 R407 R408 R409 1-216-049-11 1-216-025-11 1-216-017-11 1-216-047-11 1-216-047-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 100 47 820 820 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R460 R461 R462 R463 R464 1-216-065-11 1-216-081-00 1-216-089-11 1-216-049-11 1-216-049-11 RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 4.7K 22K 47K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R410 R411 R412 R413 R416 1-216-041-00 1-216-077-11 1-216-295-00 1-216-053-00 1-216-073-00 METAL CHIP RES-CHIP SHORT METAL CHIP METAL CHIP 470 15K 0 1.5K 10K 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R465 R466 R467 R468 R469 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R417 R418 R419 R420 R421 1-216-049-11 1-216-049-11 1-216-049-11 1-216-041-00 1-216-041-00 RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP 1K 1K 1K 470 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R470 R471 R472 R473 R474 1-216-198-11 1-216-049-11 1-216-049-11 1-216-190-00 1-216-190-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 1K 470 470 5% 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/8W 1/8W R422 R423 R424 R425 R426 1-216-073-00 1-216-049-11 1-216-041-00 1-216-041-00 1-216-049-11 METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP 10K 1K 470 470 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R475 R476 R477 R478 R479 1-216-049-11 1-216-049-11 1-216-073-00 1-216-049-11 1-216-049-11 RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 1K 1K 10K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R427 R428 R429 R430 R431 1-216-073-00 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R480 R481 R482 R483 R484 1-216-049-11 1-216-025-11 1-216-049-11 1-216-025-11 1-216-049-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 100 1K 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R432 R433 R434 1-216-049-11 RES-CHIP 1-216-049-11 RES-CHIP 1-216-049-11 RES-CHIP 1K 1K 1K 5% 5% 5% 1/10W 1/10W 1/10W R485 R486 R487 1-216-065-11 RES-CHIP 1-216-065-11 RES-CHIP 1-216-065-11 RES-CHIP 4.7K 4.7K 4.7K 5% 5% 5% 1/10W 1/10W 1/10W TEL 13942296513 www . Ref. No. Remark QQ 376315150 892498299 xiaoy u163. com – 123 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 Description 2.2K 100 10K 10K 47 QQ QQ Part No. METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP 13942296513 13942296513 Description 1-216-057-00 1-216-025-11 1-216-073-00 1-216-073-00 1-216-166-00 TEL TEL Part No. R304 R306 R307 R308 R309 http://www.xiaoyu163.com QQ 376315150 892498299 MAIN Ref. No. POWER 1/10W 1/10W 1/10W 1/10W 1/10W Remark Ref. No. C905 C906 C907 C908 C909 1-163-037-11 1-163-037-11 1-163-037-11 1-163-037-11 1-163-037-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.022uF 0.022uF 0.022uF 0.022uF 0.022uF 10% 10% 10% 10% 10% 25V 25V 25V 25V 25V R493 R494 R495 R496 R497 1-216-049-11 1-216-073-00 1-216-049-11 1-216-049-11 1-216-049-11 RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 1K 10K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C910 C911 C912 C913 C914 1-163-037-11 1-163-037-11 1-163-037-11 1-163-037-11 1-163-037-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.022uF 0.022uF 0.022uF 0.022uF 0.022uF 10% 10% 10% 10% 10% 25V 25V 25V 25V 25V R498 R499 R500 R503 R504 1-216-073-00 1-216-089-11 1-216-041-00 1-216-043-11 1-216-089-11 METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 10K 47K 470 560 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C915 C916 C917 C918 C919 1-163-037-11 1-163-037-11 1-163-021-11 1-163-021-11 1-163-021-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.022uF 0.022uF 0.01uF 0.01uF 0.01uF 10% 10% 10% 10% 10% 25V 25V 50V 50V 50V R505 R506 R507 R508 R509 1-216-085-00 1-216-073-00 1-216-049-11 1-216-049-11 1-216-037-00 METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP 33K 10K 1K 1K 330 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 0 C920 0 C922 0.01uF 0.01uF 20% 20% 250V 250V R510 R511 R512 R513 R514 1-216-041-00 1-216-025-11 1-216-295-00 1-216-049-11 1-216-049-11 METAL CHIP RES-CHIP SHORT RES-CHIP RES-CHIP 470 100 0 1K 1K 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W 0 R515 R520 R521 R522 R523 1-260-300-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 RES, CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP 4.7 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/2W 1/10W 1/10W 1/10W 1/10W R524 R525 R526 R527 R528 1-216-049-11 1-216-049-11 1-216-049-11 1-216-041-00 1-216-097-11 RES-CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP 1K 1K 1K 470 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R529 R534 1-216-097-11 RES-CHIP 1-216-097-11 RES-CHIP 100K 100K 5% 5% 1/10W 1/10W 1-113-925-11 CERAMIC 1-113-925-11 CERAMIC 13942296513 < CONNECTOR > * CN903 QQ 376315150 892498299 TEL 13942296513 Remark 1-785-654-11 PIN, CONNECTOR (PC BOARD) 2P < DIODE > D901 D902 D903 D904 D905 8-719-046-07 8-719-046-07 8-719-046-07 8-719-046-07 8-719-046-07 DIODE DIODE DIODE DIODE DIODE 2A02M 2A02M 2A02M 2A02M 2A02M D906 D907 D908 D909 D910 8-719-046-07 8-719-046-07 8-719-046-07 8-719-063-79 8-719-063-79 DIODE DIODE DIODE DIODE DIODE 2A02M 2A02M 2A02M 1N4002B 1N4002B D911 D912 D913 D914 D915 8-719-063-79 8-719-063-79 8-719-988-61 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE DIODE 1N4002B 1N4002B 1SS355TE-17 1SS355TE-17 1SS355TE-17 QQ 376315150 892498299 < VIBRATOR > < FUSE > X401 1-781-598-11 VIBRATOR, CERAMIC (8MHz) X402 1-767-697-11 VIBRATOR, CRYSTAL (32kHz) X403 1-760-556-41 VIBRATOR, CRYSTAL (4.332MHz) ************************************************************* 0 F901 0 F902 0 F903 1-532-467-51 FUSE (315mA/250V) 1-532-388-51 FUSE (2A/250V) 1-532-464-51 FUSE (2.5A/250V) < JACK > A-3322-536-A POWER BOARD, COMPLETE *********************** * 0 J901 1-526-838-11 INLET, AC 2P (- AC IN) 1-533-233-31 HOLDER, FUSE < LINE FILTER > 0 LF901 < CAPACITOR > C901 C902 C903 C904 1-163-037-11 1-163-037-11 1-163-037-11 1-163-037-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP www . 0.022uF 0.022uF 0.022uF 0.022uF 10% 10% 10% 10% 25V 25V 25V 25V 1-402-663-11 TRANSFORMER, LINE FILTER (LFT) < IC LINK > 0 PS901 1-532-605-00 LINK, IC (ICP-N10) 0.4A xiaoy u163. com The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. – 124 – http://www.xiaoyu163.com 376315150 892498299 5% 5% 5% 5% 5% QQ Description 470 1K 1K 1K 1K 13942296513 Part No. METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP TEL Description 1-216-041-00 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 TEL Part No. R488 R489 R490 R491 R492 http://www.xiaoyu163.com QQ 376315150 892498299 POWER Ref. No. Part No. Description Remark Ref. No. S638 S640 S641 S642 S643 < TRANSISTOR > Q901 Q902 8-729-027-50 TRANSISTOR DTC123JKA-T146 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR SW TOP TUNER Part No. Description 1-762-798-11 1-762-798-11 1-762-798-11 1-762-798-11 1-762-798-11 SWITCH, KEY BOARD (CD x) SWITCH, KEY BOARD (VOLUME–) SWITCH, KEY BOARD (VOLUME+) SWITCH, KEY BOARD (REC/REC MODE) SWITCH, KEY BOARD (CD u) Remark < RESISTOR > R901 R902 R905 R906 1-216-073-00 1-216-089-11 1-216-089-11 1-216-073-00 METAL CHIP RES-CHIP RES-CHIP METAL CHIP 10K 47K 47K 10K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W S644 1-762-798-11 SWITCH, KEY BOARD (TUNE > +) S645 1-762-798-11 SWITCH, KEY BOARD (TUNE . –) S646 1-762-798-11 SWITCH, KEY BOARD (LINE/LINE LEVEL) ************************************************************* A-3322-527-A TUNER BOARD, COMPLETE *********************** * < RELAY > RY901 < CAPACITOR > 1-755-363-11 RELAY 0 T901 1-435-321-11 TRANSFORMER, POWER ************************************************************* < CONNECTOR > * CN601 1-506-486-11 PIN, CONNECTOR 7P < SWITCH > 10% 10% 10% 20% 5% 50V 50V 50V 10V 50V C6 C7 C9 C10 C11 1-163-021-11 1-163-037-11 1-163-113-00 1-163-809-11 1-163-251-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.022uF 68PF 0.047uF 100PF 10% 10% 5% 10% 5% 50V 25V 50V 25V 50V C12 C13 C14 C15 C16 1-163-133-00 1-163-263-11 1-163-222-11 1-163-037-11 1-126-962-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 470PF 330PF 5PF 0.022uF 3.3uF 5% 5% 0.25PF 10% 20% 50V 50V 50V 25V 50V C17 C18 C21 C22 C23 1-128-551-11 1-163-809-11 1-163-021-11 1-126-934-11 1-163-809-11 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 22uF 0.047uF 0.01uF 220uF 0.047uF 20% 10% 10% 20% 10% 25V 25V 50V 10V 25V C24 C26 C27 C28 C29 1-163-021-11 1-126-963-11 1-163-809-11 1-126-964-11 1-163-009-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP 0.01uF 4.7uF 0.047uF 10uF 0.001uF 10% 20% 10% 20% 10% 50V 50V 25V 50V 50V C30 C31 C32 C33 C34 1-164-004-11 1-163-017-00 1-163-021-11 1-163-021-11 1-163-021-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.0047uF 0.01uF 0.01uF 0.01uF 10% 5% 10% 10% 10% 25V 50V 50V 50V 50V C35 C36 C37 C38 C39 1-163-024-00 1-163-024-00 1-164-346-11 1-107-823-11 1-164-346-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.018uF 0.018uF 1uF 0.47uF 1uF 10% 10% 50V 50V 16V 16V 16V C40 C41 C42 C43 C44 1-126-960-11 1-126-960-11 1-126-934-11 1-163-021-11 1-163-009-11 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP 1uF 1uF 220uF 0.01uF 0.001uF 20% 20% 20% 10% 10% QQ 376315150 892498299 TEL 13942296513 1-675-213-13 TOP BOARD ********** * 0.01uF 0.01uF 0.01uF 220uF 100PF < RESISTOR > R654 R655 R656 R657 R658 1-216-045-00 1-216-048-00 1-216-051-00 1-216-056-00 1-216-061-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 680 910 1.2K 2K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R660 R661 R662 R663 R664 1-216-045-00 1-216-048-00 1-216-051-00 1-216-056-00 1-216-061-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 680 910 1.2K 2K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R665 1-216-069-00 METAL CHIP 6.8K 5% 1/10W < SWITCH > S633 S634 S635 S636 S637 1-762-798-11 1-762-798-11 1-762-798-11 1-762-798-11 1-762-798-11 www . SWITCH, KEY BOARD (MEGA BASS) SWITCH, KEY BOARD (SOUND) SWITCH, KEY BOARD (MD x) SWITCH, KEY BOARD (MD u) SWITCH, KEY BOARD (RADIO/BAND) xiaoy u163. com 10% 50V 50V 10V 50V 50V The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. – 125 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 1-572-126-21 SWITCH, PUSH (1 KEY) (REC POSITION) 1-572-126-21 SWITCH, PUSH (1 KEY) (PACK OUT) 1-771-264-11 SWITCH, PUSH (DETECTION) (1 KEY) (PLAY POSITION) ************************************************************* CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP QQ QQ S601 S602 S604 1-163-021-11 1-163-021-11 1-163-021-11 1-126-934-11 1-163-251-11 13942296513 13942296513 1-671-115-21 SW BOARD ********** * C1 C2 C3 C4 C5 TEL TEL < TRANSFORMER > http://www.xiaoyu163.com QQ 376315150 892498299 TUNER Ref. No. Part No. Description C45 C46 C47 C48 C49 1-163-021-11 1-163-227-11 1-163-227-11 1-107-823-11 1-126-935-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.01uF 10PF 10PF 0.47uF 470uF 10% 0.50PF 0.50PF 10% 20% 50V 50V 50V 16V 6.3V Remark C50 C51 C52 C53 C54 1-163-021-11 1-163-009-11 1-163-009-11 1-163-017-00 1-163-133-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.001uF 0.001uF 0.0047uF 470PF 10% 10% 10% 5% 5% 50V 50V 50V 50V 50V C55 C56 C57 C58 C59 1-163-133-00 1-163-251-11 1-163-021-11 1-126-934-11 1-163-251-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 470PF 100PF 0.01uF 220uF 100PF 5% 5% 10% 20% 5% 50V 50V 50V 16V 50V C60 C61 C71 C72 1-163-021-11 1-163-021-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 0.001uF 0.001uF 10% 10% 10% 10% 50V 50V 50V 50V Ref. No. Part No. Description Remark < IC > IC1 IC2 8-759-663-31 IC LA1833N 8-759-483-40 IC LC72137M-TLM < JUMPER RESISTOR > JC1 JC2 JC3 JC4 JC5 1-216-295-00 1-216-296-00 1-216-295-00 1-216-295-00 1-216-296-00 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 JC6 1-216-296-00 SHORT 0 < COIL > < FILTER > CF1 CF2 CF3 CF4 1-781-407-11 1-781-407-11 1-781-344-11 1-781-817-11 INDUCTOR CHIP 1.2uH COIL, MW ANT COIL, LW ANT COIL, MW OSC INDUCTOR 10mH 13942296513 13942296513 1-410-994-22 1-416-991-11 1-416-129-11 1-411-959-11 1-410-071-11 TEL TEL L1 L3 L4 L5 L6 < TRANSISTOR > FILTER, CERAMIC FILTER, CERAMIC FILTER, MW CERAMIC DISCRIMINATOR, CERAMIC FET 2SK193TP-E TRANSISTOR DTC343TK-T-146 TRANSISTOR 2SC2059K-T146-N TRANSISTOR 2SC2413KT146-PQ TRANSISTOR 2SC2413KT146-PQ Q6 Q7 Q8 Q9 8-729-920-31 8-729-027-23 8-729-120-28 1-801-806-11 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR < CONNECTOR > 1-566-690-11 PLUG, CONNECTOR (2.5mm) 2P < TRIMMER > CT1 CT2 CT3 CT4 1-141-459-11 1-141-601-11 1-141-459-11 1-141-601-11 CAP, TRIMMER (SEAL TYPE) 45PF CAP, ADJ 10PF CAP, TRIMMER (SEAL TYPE) 45PF CAP, ADJ 10PF < DIODE > D1 D2 D3 D4 D5 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE DIODE 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 D6 D7 D8 D9 D10 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE DIODE 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 D11 D12 8-719-050-69 DIODE KV1520NT-2 8-719-988-61 DIODE 1SS355TE-17 < FERRITE BEAD > FB1 1-500-445-21 FERRITE, EMI (SMD) www . DTC343TK-T-146 DTA114EKA-T146 2SC2412K-T-146-QR DTC144EKA-T146 QQ 376315150 892498299 TEL 13942296513 CN2 < RESISTOR > R1 R2 R3 R4 R5 1-216-017-11 1-216-017-11 1-216-017-11 1-216-041-00 1-216-295-00 RES-CHIP RES-CHIP RES-CHIP METAL CHIP SHORT 47 47 47 470 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R6 R7 R8 R9 R11 1-216-057-00 1-216-073-00 1-216-097-11 1-216-057-00 1-216-061-00 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 2.2K 10K 100K 2.2K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R12 R13 R16 R17 R18 1-216-069-00 1-216-073-00 1-216-105-11 1-216-037-00 1-216-009-11 METAL CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP 6.8K 10K 220K 330 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R19 R20 R21 R22 R23 1-216-057-00 1-216-033-00 1-216-025-11 1-216-079-00 1-216-079-00 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 2.2K 220 100 18K 18K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R24 1-216-093-11 RES-CHIP 68K 5% 1/10W xiaoy u163. com – 126 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 8-729-119-32 8-729-920-31 8-729-920-38 8-729-931-02 8-729-931-02 QQ QQ Q1 Q2 Q3 Q4 Q5 http://www.xiaoyu163.com QQ 376315150 892498299 TUNER Ref. No. 5% 5% 5% 5% 5% 1/10W 1/8W 1/10W 1/10W 1/10W Remark R30 R31 R32 R33 R34 1-216-049-11 1-216-073-00 1-216-065-11 1-216-081-00 1-216-025-11 RES-CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP 1K 10K 4.7K 22K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R35 R36 R37 R38 R39 1-216-073-00 1-216-025-11 1-216-049-11 1-216-025-11 1-216-049-11 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 100 1K 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R40 R41 R42 R43 R44 1-216-025-11 1-216-025-11 1-216-065-11 1-216-057-00 1-216-025-11 RES-CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP 100 100 4.7K 2.2K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R45 R46 R47 R48 R49 1-216-025-11 1-216-025-11 1-216-025-11 1-216-065-11 1-216-073-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 100 100 100 4.7K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R50 R51 R52 R53 R54 1-216-065-11 1-216-027-00 1-216-021-00 1-216-021-00 1-216-021-00 RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 120 68 68 68 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R55 R56 R57 R72 1-216-065-11 1-216-073-00 1-216-013-00 1-216-017-11 RES-CHIP METAL CHIP METAL CHIP RES-CHIP 4.7K 10K 33 47 5% 5% 5% 5% Ref. No. Description Remark MISCELLANEOUS *************** 60 61 103 106 118 1-791-523-11 1-791-522-11 1-791-521-11 1-791-520-11 1-791-518-11 WIRE, PARALLEL (FFC) (13 CORE) WIRE, PARALLEL (FFC) (10 CORE) WIRE, PARALLEL (FFC) (10 CORE) WIRE, PARALLEL (FFC) (18 CORE) WIRE, PARALLEL (FFC) (16 CORE) 154 155 156 * 258 0 260 1-791-519-11 1-791-531-21 1-791-532-21 1-667-954-11 A-4672-541-A WIRE, PARALLEL (FFC) (26 CORE) WIRE, PARALLEL (FFC) (21 CORE) WIRE, PARALLEL (FFC) (23 CORE) FLEXIBLE BOARD PICK-UP ASSY, OPTICAL KMS-260B (MD) 273 TEL 13942296513 Part No. ANT1 0 F901 A-4672-475-A MOTOR ASSY, SPINDLE (SPINDLE) (INCLUDING M101) (MD) 8-848-483-05 PICK-UP, OPTICAL KSS-213C (CD) X-2626-202-1 CHASSIS ASSY, MOTOR (MB) (SPINDLE) (INCLUDING M701) (CD) 1-501-452-11 ANTENNA, TELESCOPIC 1-532-467-51 FUSE (315mA/250V) 0 F902 0 F903 HR901 M102 M103 1-532-388-51 1-532-464-51 1-500-502-11 A-4672-474-A X-4949-264-1 0 303 304 M702 S102 FUSE (2A/250V) FUSE (2.5A/250V) HEAD, OVER WRITE MOTOR ASSY, SLED (SLED) (MD) MOTOR ASSY, LOADING (LOADING) (MD) X-2625-769-1 GEAR ASSY, MOTOR (MB) (RP) (SLED) (CD) 1-762-148-21 SWITCH, PUSH (2 KEY) (REFLECT RATE DETECT,PROTECT DETECT) 1-692-960-11 SWITCH, PUSH (1 KEY) (CD DOOR) 1-529-463-11 SPEAKER (8cm) (L-CH) 1-529-463-11 SPEAKER (8cm) (R-CH) QQ 376315150 892498299 1/10W 1/10W 1/10W 1/10W S402 SP101 SP201 0 T901 1-435-321-11 TRANSFORMER, POWER ************************************************************* < TRANSFORMER > T1 1-433-741-11 TRANSFORMER, IF < TERMINAL > TB1 1-537-489-21 TERMINAL BOARD (ANT) < TUNER > TU1 1-693-495-11 TUNER UNIT < VIBRATOR > X1 1-760-130-11 VIBRATOR, CRYSTAL (75kHz) ************************************************************* www . xiaoy u163. com The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. – 127 – http://www.xiaoyu163.com 376315150 892498299 376315150 892498299 220K 2.2K 2.2K 3.3K 82 QQ QQ RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 13942296513 13942296513 Description 1-216-105-11 1-216-206-00 1-216-057-00 1-216-061-00 1-216-023-00 TEL TEL Part No. R25 R26 R27 R28 R29 http://www.xiaoyu163.com ZS-M35 QQ 376315150 892498299 Ref. No. Part No. Description Remark ACCESSORIES & PACKING MATERIALS ******************************** 1-754-102-21 1-769-412-11 1-770-019-11 3-027-153-21 3-867-609-21 0 0 ANTENNA, LOOP (MW/LW) (ANT2) CORD, POWER ADAPTOR, CONVERSION PLUG 3P (UK) LID, BATTERY CASE (for RMT-CM35) MANUAL, INSTRUCTION (ENGLISH,SPANISH) (AEP,UK) TEL TEL 13942296513 13942296513 3-867-609-31 MANUAL, INSTRUCTION (FRENCH,GERMAN) (AEP) 3-867-609-41 MANUAL, INSTRUCTION (DUTCH,PORTUGUESE) (AEP) 3-867-609-51 MANUAL, INSTRUCTION (ITALIAN) (AEP) 3-867-609-61 MANUAL, INSTRUCTION (SWEDISH,FINNISH) (CET) 3-867-609-71 MANUAL, INSTRUCTION (POLISH,CZECH,HUNGARIAN) (CET) 3-867-609-81 MANUAL, INSTRUCTION (RUSSIAN,SLOVAKIAN) (CET) X-3378-617-1 REMOTE CONTROLLER (RMT-CM35) ************************************************************* ************** HARDWARE LIST ************** SCREW +BVTP 3X14 TYPE2 N-S SCREW +BVTP 3X12 TYPE2 N-S SCREW +BVTP 3X10 TYPE2 N-S SCREW +BTP 2.6X6 TYPE2 N-S SCREW +P 2.6X5 #6 #7 #8 #9 #10 7-685-133-19 7-682-549-04 7-621-772-20 7-621-772-40 7-627-852-08 SCREW (DIA.2.6) (IT3B) SCREW +B 3X10 SCREW +B 2X5 SCREW +B 2X8 SCREW, PRECISION +P 1.7X2.5 #11 7-685-661-79 SCREW +BVTP 4X12 TYPE2 N-S TEL 13942296513 www 9-927-183-11 . QQ 376315150 892498299 xiaoy u163. com The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Sony Corporation Personal Audio Division Company – 128 – http://www.xiaoyu163.com 2000B0451-1 Printed in Japan C2000. 2 Published by General Engineering Dept. 376315150 892498299 376315150 892498299 7-685-649-79 7-685-648-79 7-685-647-79 7-685-533-19 7-621-770-87 QQ QQ #1 #2 #3 #4 #5