Xm-d1000p5 Monaural Power Amplifier

Transcript

XM-D1000P5 SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Ver 1.0 2003. 02 SPECIFICATIONS AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 500 watts minimum continuous average power into 4 ohms, 20 Hz to 300 Hz with no more than 0.2% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications Circuit system Class D Technology Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Through out pin jacks Suitable speaker impedance 2–8Ω Maximum outputs 1,000 W (at 4 Ω) 1,600 W (at 2 Ω) Rated outputs (supply voltage at 14.4 V) 500 W (20 – 300 Hz, 0.2% THD, at 4 Ω) 900 W (20 – 300 Hz, 0.6% THD, at 2 Ω) Frequency response 5 – 300 Hz ( +0.5 –3 dB) Harmonic distortion 0.06% or less (at 100 Hz, 4 Ω) Input level adjustment range 0.3 – 6.0 V (RCA pin jacks) 1.2 – 12.0 V (High level input) Low-pass filter Low boost Power requirements Power supply voltage Current drain Dimensions Mass Supplied accessories 50 – 300 Hz, –12 dB/oct 0 – 10 dB (40 Hz) 12 V DC car battery (negative ground) 10.5 – 16 V at rated output : 90 A (at 2 Ω) Remote input : 2 mA Approx. 347 × 57 × 339 mm (13 3/4 × 2 1/4 × 13 3/8 in.) (w/h/d) not incl. projecting parts and controls Approx. 3.8 kg (8 lb. 6 oz.) not incl. accessories Mounting screws (5) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice. Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. MONAURAL POWER AMPLIFIER 9-877-039-01 Sony Corporation 2003B0400-1 © 2003. 02 e Vehicle Company Published by Sony Engineering Corporation 1 XM-D1000P5 TABLE OF CONTENTS 1. GENERAL Location and Function of Controls .......................................... 3 Connections ............................................................................. 4 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5. Bottom Plate ........................................................................ 6 Main Board Section ............................................................. 7 Disassembly and Assembly of Ornamental Plate ................ 7 Main Board .......................................................................... 8 LED Board ........................................................................... 8 3. DIAGRAMS 3-1. 3-2. 3-3. 3-4. 3-5. IC Block Diagram ................................................................ 9 Printed Wiring Boards –Main Section (1/2)– .................... 10 Printed Wiring Boards –Main Section (2/2)– .................... 11 Schematic Diagram –Main Section (1/2)– ........................ 12 Schematic Diagram –Main Section (2/2)– ........................ 13 4. EXPLODED VIEWS 4-1. Heat Sink (Main) Section .................................................. 15 4-2. Main Board Section ........................................................... 16 5. ELECTRICAL PARTS LIST ......................................... 17 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 2 ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. XM-D1000P5 SECTION 1 GENERAL Location and Function of Controls This section is extracted from instruction manual. Emplacement et fonction des commandes 1 POWER/PROTECTOR indicator Lights up in green during operation. When the PROTECTOR is activated the indicator will change from green to red. When the PROTECTOR is activated refer to the TroubleShooting Guide. 2 Cut-off frequency adjustment control Sets the cut-off frequency (50 – 300 Hz) for the low-pass filters. 3 LOW BOOST level control Turn this control to boost the frequencies around 40 Hz to a maximum of 10 dB. 4 LEVEL adjustment control The input level can be adjusted with this control. Turn it in the clockwise direction when the output level of the car audio unit seems low. 1 Indicateur POWER/PROTECTOR S’allume en vert en cours de fonctionnement. Lorsque PROTECTOR est activé, le voyant passe du vert au rouge. Lorsque PROTECTOR est activé, reportez-vous au guide de dépannage. 2 Commandes de réglage de la fréquence de coupure Règle la fréquence de coupure (50 – 300 Hz) pour les filtres passe-bas. 3 Commande de niveau LOW BOOST Tournez cette commande pour amplifier les fréquences autour de 40 Hz à un maximum de 10 dB. 4 Commande de réglage LEVEL Le niveau d ’entrée peut se régler avec cette commande. Tournez cette commande dans le sens des aiguilles d’une montre lorsque le niveau de sortie de l’autoradio semble faible. POWER/PROTECTOR LPF 100 70 LOW BOOST (40Hz) LEVEL 0.5 2 4 50 300Hz 0 +10dB 6 0.3V Low boost/ Amplification de basses fréquences Low Pass Filter/ Filtre passe-bas dB dB 10 10 0 -10 LOW PASS -20 0 300Hz -30 100Hz -40 -50 50Hz 10 40 100 1k -60 10 Frequency/Fréquence Hz 100 Frequency/Fréquence 1k 2k Hz Circuit Diagram/ Schéma du circuit Buffer Lch Power AMP LPF INPUT LEVEL Rch LOW BOOST Lch THROUGH OUT Rch 3 XM-D1000P5 Connections Connexions Caution Attention • Before making any connections, disconnect the ground terminal of the car battery to avoid short circuits. • Be sure to use speakers with an adequate power rating. If you use small capacity speakers, they may be damaged. • Do not connect the # terminal of the speaker system to the car chassis, and do not connect the # terminal of the right speaker with that of the left speaker. • Install the input and output cords away from the power supply wire as running them close together can generate some interference noise. • This unit is a high powered amplifier. Therefore, it may not perform to its full potential if used with the speaker cords supplied with the car. • If your car is equipped with a computer system for navigation or some other purpose, do not to remove the ground wire from the car battery. If you disconnect the wire, the computer memory may be erased. To avoid short circuits when making connections, disconnect the +12 V power supply wire until all the other wires have been connected. • Avant d’effectuer les connexions, débranchez la borne de masse de la batterie de voiture pour éviter tout court-circuit. • Veillez à utiliser des haut-parleurs de puissance adéquate. Si vous utilisez des hautparleurs de faible capacité, ils risquent d’être endommagés. • Ne raccordez pas la borne # du système de haut-parleurs à la carrosserie de la voiture ni la borne # du haut-parleur droit avec celle du haut-parleur gauche. • Eloignez les câbles d’entrée et de sortie du câble d’alimentation pour éviter les interférences. • Cet appareil est un amplificateur de haute puissance. Il ne peut donc déployer sa pleine puissance que si les câbles de haut-parleurs de la voiture lui sont raccordés. • Si votre voiture est équipée d’un système de navigation ou d’un ordinateur de bord, ne retirez pas le câble de terre de la batterie de la voiture, sinon les données mémorisées seront effacées. Pour éviter un court-circuit lorsque vous effectuez les branchements, branchez le câble d’alimentation +12 V après avoir branché tous les autres câbles. Precautions • This unit is designed for negative ground 12 V DC operation only. • Use speakers with suitable impedance. — 2 to 8 Ω. • Do not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit. Doing so may damage the active speakers. • Avoid installing the unit in areas subject to: — high temperatures such as from direct sunlight or hot air from the heater — rain or moisture — dust or dirt • If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car, allow the unit to cool down before use. • When installing the unit horizontally, be sure not to cover the fins with the floor carpet etc. • If this unit is placed too close to the car audio unit or antenna, interference may occur. In this case, relocate the amplifier away from the car audio unit or antenna. • If no power is being supplied to the car audio unit, check the connections. • This power amplifier employs a protection circuit * to protect the transistors and speakers if the amplifier malfunctions. Do not attempt to test the protection circuits by covering the heat sink or connecting improper loads. • Do not use the unit on a weak battery as its optimum performance depends on a good power supply. • For safety reasons, keep your car audio volume moderate so that you can still hear sounds outside your car. Make the terminal connections as illustrated below. Effectuez les connexions des bornes comme illustré ci-dessous. Fuse Replacement If the fuse blows, check the power connection and replace all fuses. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Warning When replacing the fuse, be sure to use one matching the amperage stated above the fuse holder. Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. ∗ Protection circuit This amplifier is provided with a protection circuit that operates in the following cases: — when the unit is overheated — when a DC current is generated — when the speaker terminals are short circuited. The POWER/PROTECTOR indicator lights up in red and the unit will shut down. If this happens, turn off the connected equipment, take out the cassette tape or disc, and determine the cause of the malfunction. If the amplifier has overheated, wait until the unit cools down before use. If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer. 3 3 REM +12V GND c Pass the wires through the cap, connect the wires, then cover the terminals with the cap. Faites passer les câbles par le cache, raccordez les câbles, puis recouvrez les bornes avec le cache. Note When you tighten the screw, be careful not to apply too much torque * as doing so may damage the screw. * The torque value should be less than 1 N•m. Remarque Lorsque vous vissez la vis, faites attention à ne pas appliquer une trop grande force *, car cela pourrait endommager la vis. * Le couple de torsion doit être inférieur à 1 N•m. Power Connection Wires Câbles d’alimentation Remote output * Sortie de télécommande * (REM OUT) to a metal point of the car Car audio unit Autoradio vers une partie métallique de la carrosserie Fuse (150 A) Fusible (150 A) +12 V car battery Batterie de voiture +12 V * If you have the factory original or some other car audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. * Si vous disposez du modèle d’origine ou d’un autre autoradio dont l’amplificateur ne comporte pas de sortie de télécommande, raccordez la borne d’entrée de télécommande (REMOTE) à la prise d’alimentation accessoires. Notes on the power supply • Connect the +12 V power supply wire only after all the other wires have been connected. • Be sure to connect the ground wire of the unit securely to a metal point of the car. A loose connection may cause a malfunction of the amplifier. • Be sure to connect the remote control wire of the car audio unit to the remote terminal. • When using a car audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessorypower supply. • Use the power supply wire with a fuse attached (150 A). • Place the fuse in the power supply wire as close as possible to the car battery. • Make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least 4-Gauge (AWG-4) or have a sectional area of more than 22.0 mm 2. 4 Remarques sur l’alimentation électrique • Raccordez le câble d’alimentation +12 V uniquement après avoir réalisé toutes les autres connexions. • Raccordezcorrectement le câble de masse à une partie métallique de la voiture. Une connexion lâche peut provoquer un dysfonctionnement de l’amplificateur. • Veillez à raccorder le fil de télécommande de l’autoradio à la borne de télécommande. • Si vous utilisez un l’autoradio dont l’amplificateur ne comporte pas de sortie de télécommande, raccordez la borne d’entrée de la télécommande (REMOTE) à la prise d’alimentation accessoires. • Utilisez un câble d’alimentation muni d’un fusible (150 A). • Fixez le câble d’alimentation le plus près possible de la batterie de voiture. • Assurez-vous que les câbles à raccorder aux bornes +12V et GND de cet appareil sont d’un calibre d’au moins 4 (AWG-4) ou d’une section supérieure à 22, 0 mm 2. Précautions • Cet appareil est conçu pour fonctionner sur du courant continu 12 V à masse négative. • Utilisez des haut-parleurs d’une impédance appropriée. — 2 à 8 Ω. • Ne raccordez pas de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes de hautparleurs de cet appareil. Cette opération pourrait endommager les haut-parleurs actifs. • N’installez pas l’appareil à un endroit exposé à : — de hautes températures comme sous le rayonnement direct du soleil ou près d’un conduit de chauffage — la pluie ou à l’humidité — de la poussière ou à des saletés • Si votre voiture est garée en plein soleil et que la température à l’intérieur de l’habitacle a considérablement augmenté, laissez refroidir l’appareil avant de l’utiliser. • Lorsque vous installez l’appareil à l’horizontale, veillez à ne pas recouvrir la grille d’aération avec le tapis, etc. • Si cet appareil est placé trop près de l’autoradio ou de l’antenne, il se peut que des interférences se produisent. Dans ce cas, éloignez l’amplificateur de l’autoradio ou de l’antenne. • Si l’autoradio n’est pas alimenté, vérifiez les branchements. • Cet amplificateur de puissance utilise un circuit de protection * visant à protéger les transistors et les haut-parleurs en cas de dysfonctionnement de l’amplificateur. Ne tentez pas de tester les circuits de protection en couvrant l’accumulateur de chaleur ou en branchant des charges inadéquates. • N’utilisez pas cet appareil avec une batterie faible car les performances optimales de l’appareil dépendent d’une bonne alimentation électrique. • Pour des raisons de sécurité, gardez le volume de votre installation audio de voiture à un niveau permettant encore la perception des bruits extérieurs. Remplacement du fusible Si le fusible fond, vérifiez le branchement de l’alimentation et remplacez tous les fusibles. Si le fusible grille encore après ce remplacement, il est possible qu’il y ait un dysfonctionnement interne. Dans ce cas, adressez-vous à votre distributeur Sony le plus proche. Avertissement Lors du remplacement du fusible, veillez à respecter l’ampérage indiqué au-dessus du logement du fusible. N’utilisez jamais un fusible d’ampérage supérieur à celui fourni avec l’appareil, car cela pourrait endommager l’appareil. * Circuit de protection Cet amplificateur est équipé d’un circuit de protection qui s’active dans les cas suivants : — en cas de surchauffe de l’appareil — en cas de génération d’un courant continu — lorsque les bornes de haut-parleurs sont courtcircuitées. L’indicateur POWER/PROTECTOR s’allume en rouge et l’appareil s’arrête. Dans ce cas, éteignez tout équipement raccordé, retirez la cassette ou le disque et déterminez la cause du dysfonctionnement. Si l’amplificateur a surchauffé, attendez que l’appareil refroidisse avant de le réutiliser. Si vous avez des questions ou des problèmes concernant votre appareil qui ne sont pas abordés dans ce mode d’emploi, adressez-vous à votre distributeur Sony le plus proche. XM-D1000P5 Input Connections Connexions d’entrée For details on the settings of switches and controls, refer to “Location and Function of Controls.” Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à “Emplacement et fonction des commandes”. Line Input Connection (with Speaker Connection 1 or 2) A Connexion d’entrée de ligne (avec connexion de haut- B Line Input Connection (with Speaker Connection 3) Connexion d’entrée de ligne (avec connexion de hautparleur 3) parleur 1 ou 2) Car audio unit Autoradio Car audio unit Autoradio LINE OUT* * • You can connect either output terminal. • The minimum resistance must be 2 Ω in total. Right channel Canal droit Left channel Canal gauche LINE OUT* * • Peu importe la borne de sortie que vous raccordez. • La résistance minimale doit être égale à 2 Ω au total. Line Input Connection (with Speaker Connection 4) Connexion d’entrée de ligne (avec connexion de haut- C * • You can connect either output terminal. • The minimum resistance must be 2 Ω in total. * • Peu importe la borne de sortie que vous raccordez. • La résistance minimale doit être égale à 2 Ω au total. High Level Input Connection (with Speaker Connection 1) D Connexion à l’entrée de haut niveau (avec connexion parleur 4) de haut-parleur 1) Car audio unit Autoradio Left speaker Haut-parleur gauche LINE OUT Car audio unit Autoradio Right speaker Haut-parleur droit INPUT THROUGH OUT INPUT 2 When you connect amplifiers using with the THROUGH OUT pin jacks, it allows you to connect up to a maximum of three. Otherwise the necessary output levels can not be obtained, and your car audio unit may be damaged. Lorsque vous raccordez des amplificateurs à l’aide des prises à broches THROUGH OUT, vous pouvez raccorder jusqu’à 3 amplificateurs au maximum. Sinon les niveaux de sortie requis ne peuvent pas être obtenus et votre autoradio risque d’être endommagé. Use the THROUGH OUT terminal when you install more amplifiers. The signals are output as they were input. (LOW BOOSTdo not work.) Utilisez la borne THROUGH OUT lorsque vous installez plusieurs amplificateurs. Les signaux sont sortis comme ils sont entrés. (LOW BOOSTne fonctionnent pas.) Grey/Black striped Rayé gris/noir Grey Gris White/Black striped Rayé blanc/noir White Blanc Speaker Connections Raccordement de haut-parleurs For details on the settings of switches and controls, refer to “Location and Function of Controls.” Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à “Emplacement et fonction des commandes”. 1-Speaker System (with Input Connection A or D) Système à 1 haut-parleur (avec connexion d’entrée A ou 1 2-Speaker System (with Input Connection A) Système à 2 haut-parleurs (avec connexion d’entrée A) 2 D) Subwoofer* (min. TOTAL 4 Ω) Caisson de grave* (min. TOTAL 4 Ω) Subwoofer (min. TOTAL 2 Ω) Caisson de grave (min. TOTAL 2 Ω) * When you use two terminals with speakers, each of terminal resistance is 4 Ω at a minimum. (Two terminals are connected with each other in the unit.) 1-Speaker System (with Input Connection B) Système à 1 haut-parleur (avec connexion d’entrée B) 3 Subwoofer* (min. TOTAL 4 Ω) Caisson de grave* (min. TOTAL 4 Ω) * Lorsque vous utilisez deux bornes avec des hautparleurs, la résistance de chaque borne doit au moins être égale à 4 Ω. (Les deux bornes sont raccordées l’une à l’autre dans l’appareil.) 2-Way System (with Input Connection C) Système à 2 voies (avec connexion d’entrée C) 4 Subwoofer (min. TOTAL 2 Ω) Caisson de grave (min. TOTAL 2 Ω) Left subwoofer (min. TOTAL 2 Ω) Caisson de grave gauche (min. TOTAL 2 Ω) Right subwoofer (min. TOTAL 2 Ω) Caisson de grave droit (min. TOTAL 2 Ω) Full range speakers Haut-parleurs à large bande 5 XM-D1000P5 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. SET 2-1. BOTTOM PLATE (Page 6) 2-2. MAIN BOARD SECTION (Page 7) 2-4. MAIN BOARD (Page 8) 2-5. LED BOARD (Page 8) 2-3. DISASSMBLY AND ASSEMBLY OF ORNAMENTAL PLATE (Page 7) Note : Follow the disassembly procedure in the numerical order given. 2-1. BOTTOM PLATE 1 P 3x6 3 P 3x6 2 P 3x6 4 bottom plate 5 insulating sheet 6 XM-D1000P5 2-2. MAIN BOARD SECTION 2 BTP 3x14 3 BTP 3x14 5 MAIN board section 4 BTP 3x14 1 P 3x8 heat sink (main) 6 CNT2 2-3. DISASSEMBLY AND ASSEMBLY OF ORNAMENTAL PLATE At disassembly: heat sink (main) cut At assembly: ornamental plate heat sink (main) welding ornamental plate 7 XM-D1000P5 2-4. MAIN BOARD 2 P 3x8 1 P 3x8 4 MAIN board 3 panel (front) 2-5. LED BOARD 1 P 3x6 2 LED board 8 heat sink (main) XM-D1000P5 SECTION 3 DIAGRAMS • • • • • • • • • INV VREF OUT VCC C2 E2 E1 15 14 13 12 11 10 9 REF 5V ERROR 0.1V 1 2 3 4 5 6 7 8 CT RT GND C1 OSC TIME ERROR COMP EN Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié. 16 -IN Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. IC6 TL494CN NON for schematic diagram: Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • % : indicates tolerance. • 2 : nonflammable resistor. 3-1. IC BLOCK DIAGRAM +IN THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) A : B+ Line. B : B– Line. Total current is measured with no-signal condition. Power voltage is dc 14.4V and fed with regulated dc power supply from +12V and REM terminals. Voltage is dc with respect to ground under no-signal condition. Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : AUDIO for printed wiring boards: Note: • X : parts extracted from the component side. • : Pattern from the side which enables seeing. (The other layer’s patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. 9 9 XM-D1000P5 3-2. PRINTED WIRING BOARDS — MAIN SECTION (1/2) — • Refer to page 9 for Common Note on Printed Wiring Boards. 11 10 9 8 • Semiconductor Location (Side A) Ref. No. D3 D5 D9 D11 D23 D26 Location G-6 G-7 E-3 E-3 G-5 G-6 IC1 IC2 IC4 IC5 IC7 IC8 IC9 G-3 F-3 E-3 E-3 G-7 F-5 F-3 LED2 LED3 G-11 G-11 7 6 5 4 3 2 1 MAIN BOARD (SIDE A) A B C THR3 R118 F-6 F-6 G-7 G-7 G-7 G-4 G-4 H-8 G-6 G-5 G-6 G-5 G-5 F-5 F-6 E-2 G-6 G-6 G-4 G-7 G-6 R58 R115 IC7 R114 D9 C39 R63 R134 R62 R18 RS5 R23 R20 R24 R105 BCE Q10 ECB R175 C48 R172 R173 4 IC1 5 8 C2 C1 R155 C23 C12 R8 R17 RC3 C38 R181 RC4 R3 R156 R2 C21 R159 R81 R182 D23 C35 C11 R82 Q11 1 R158 C20 R1 R157 R164 C28 C50 C53 R7 C27 R6 C30 C51 C52 R163 C29 G 11 RC1 CF9 CF10 R98 R86 C34 R166 F C13 ECB R151 BCE R107 Q34 BCE AKA C54 R96 R4 Q43 R54 R150 BCE Q15 R133 BCE R108 C44 Q36 1 4 IC2 5 8 R25 Q17 14 R70 R78 4 IC9 5 8 R136 C6 R84 Q35 KAK D3 R16 R15 R174 R14 R11 D5 AKA 1 7 8 E R169 BCE Q37 R10 (11) 1-688-330- R149 C36 C43 R180 Q45 R55 BCE R183 ECB R154 R184 Q39 R87 R97 R104 R85 R103 R106 R79 R69 R68 11 Q14 BCE D26 Q42 BCE Q44 POWER/PROTECT R125 C40 R152 BCE Q16 BCE R77 R67 C31 R80 R170 R76 R74 R75 C33 LED2 (POWER) R128 Q8 C9 R26 RS1 RS2 R72 R88 Q9 BCE BCE BCE R27 R28 R5 1 C7 R132 R90 C18 C19 R91 Q7 5 4 R57 R56 R215 R116 D RV9 R29 R12 R13 1 C10 4 IC4 5 8 R109 R110 C16 1 R59 4 C15 IC5 5 8 R60 C14 R53 R51 R52 R43 D11 R50 R130 BCE Q5 BCE R65 R73 C41 Q6 BCE IC8 1 R171 R64 R66 C32 R92 C42 C37 8 R61 R127 R129 R131 R45 LED BOARD (SIDE A) R G R117 R111 R211 R119 R213 R126 CF1 R102 R47 R48 R46 R19 R112 R113 C8 R123 THR1 R302 R202 LED3 (PROTECT) Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q13 Q14 Q15 Q16 Q17 Q34 Q35 Q36 Q37 Q39 Q42 Q43 Q44 Q45 1-688-329- H (11) R83 BCE Q13 C22 RC2 R71 I 10 10 XM-D1000P5 3-3. PRINTED WIRING BOARDS — MAIN SECTION (2/2) — • Refer to page 9 for Common Note on Printed Wiring Boards. 1 2 3 4 5 6 7 8 9 10 11 MAIN BOARD (SIDE B) • Semiconductor Location (Side B) A D1 9 3 T1 FE S 4 T1 D G D2 1 FE 5 T1 FE B S 16 S D D D2 0 MC28 G G D2 2 R137 T FE 7 T1 G FE T1 1 RG12 S D FE T1 0 G S RG11 R146 D R147 EC37 EC32 EC33 FE T9 S MC16 RG7 9 RG5 2 1 EC13 RG4 EC11 CNT2 4 1 RG3 RG2 MC19 EC58 ZD6 -2 EC16 EC22 EC23 EC17 MC18 -1 -4 LF3 BD6 BD5 BD4 BD3 BD2 BD1 MC17 LF2 C17 2 MC31 MC22 EC21 Q12 B C E EC20 MC29 RJ3 MC30 MC23 MC24 I (L+R) GND (L+R) +12V REM FUSE1 FUSE2 FUSE3 40A 40A 40A SPEAKER OUT TER1 11 11 MC20 CON2 1 11 3 (11) 1-688-330- RG1 EC12 THR CNT1 HIGH LEVEL INPUT -3 H MC21 ORG BLK YEL FET1 -1 L -2 R EC54 INPUT -2 L -1 FET8 3 YEL BLK ORG 3 LED BOARD (SIDE B) FET3 EC50 FET2 Q1 EC5 EC24 EC25 EC15 2 PTC1 G D S 1 ZD1 G D S EC6 EC1 -4 R -3 G D S 10 1 ZD2 G D S EC55 EC8 EC26 EC27 IC6 MC12 Q4 C B E C B E -3 L -4 R EC3 ZD4 T1 FET5 D2 8 RG6 R101 MC15 G D S R139 R124 ZD5 R93 Q46 B C E Q2 C B E MC7 EC4 EC2 OUTPUT (THROUGH) JK1 EC7 3 4 PTC2 EC10 EC56 G ZD3 Q3 C B E EC9 MC5 MC4 MC9 MC3 -1 -2 VR3 LPF MC6 F MC10 EC52 -1 -2 RJ2 Q47 B C E EC61 G D S EC28 FET4 D13 Q20 C B E D15 D16 EC29 EC53 RJ1 D12 D8 -1 -2 VR2 LOW BOOST (40Hz) G D S EC14 EC51 G D S EC38 EC40 EC39 B C E Q30 B C E RG8 MC11 VR1 LEVEL G MC26 MC25 E D RG9 Q31 C B E Q27 B C E R121 Q23 B C E G RG10 PT1 R148 G Q19 B C E CV4 BC E Q22 CB E CV3 Q18 Q25 B C E D D R122 Q29 B C E S R143 R145 G ET F D FET7 S 20 D S Q21 C D G FE T1 2 MC27 G R144 S F G FET6 9 1 ET D D EC30 S 8 T1 FE S EC31 FE 1-688-329- 11 (11) Ref. No. D2 D8 D12 D13 D15 D16 D19 D20 D21 D22 Location F-6 E-4 E-6 E-6 E-4 E-4 A-7 B-8 B-7 B-8 FET1 FET2 FET3 FET4 FET5 FET6 FET7 FET8 FET9 FET10 FET11 FET12 FET13 FET14 FET15 FET16 FET17 FET18 FET19 FET20 G-9 G-9 G-9 F-9 F-10 E-10 E-10 D-10 C-10 C-9 C-9 B-8 A-6 A-5 B-5 B-4 B-4 C-4 C-3 C-3 IC6 F-7 PTC1 PTC2 F-6 F-6 Q1 Q2 Q3 Q4 Q12 Q18 Q19 Q20 Q21 Q22 Q23 Q25 Q27 Q29 Q30 Q31 Q46 Q47 F-4 F-4 F-4 F-4 H-9 D-3 D-3 E-6 D-4 D-3 D-3 D-3 D-3 D-3 D-3 D-4 E-7 E-7 ZD1 ZD2 ZD3 ZD4 ZD5 ZD6 F-5 F-5 F-5 F-5 F-5 G-7 XM-D1000P5 3-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 9 for Common Note on Schematic Diagram. IC1(1/2) CNT1 IC9(2/2) C21 R163 R4 C30 R6 C28 R164 R159 R11 C51 C52 C50 C53 C27 IC2(2/2) IC4(2/2) MC6 RV9 R29 R20 R3 IC1(2/2) RS2 R7 R5 MC4 EC1 R155 C13 C12 R8 EC56 R12 R23 R156 R24 EC55 R53 Q37 MC9 R50 R15 C9 CV3 CV4 R14 C10 R16 R174 R52 MC10 C16 R157 Q1 EC2 R57 EC52 Q3 C2 C23 C39 R60 R59 R28 R169 R63 R51 EC53 R158 IC5(1/2) MC3 MC7 MC5 RS1 R136 IC5(2/2) R43 VR2 VR1 C20 EC54 R26 IC2(1/2) R1 C1 EC51 R13 R27 R25 VR3 JK1 C17 IC4(1/2) RS5 D11 C29 R10 D15 R2 R62 R17 C14 EC3 C15 EC10 EC4 EC7 ZD3 EC6 EC9 EC8 ZD4 ZD1 ZD2 EC28 EC5 EC29 R18 R61 Q2 D16 Q4 (Page 13) MC31 D3 LED3 CON2 CNT2 THR1 THR2 R69 THR3 R79 R170 R171 D5 IC7 R97 MC19 EC11 R73 R77 R64 EC50 R66 Q9 R55 Q7 C36 R54 Q8 C35 Q11 LED2 R85 C6 R68 ZD6 R149 R75 Q14 R81 Q6 R104 Q39 R76 EC12 R74 R78 R70 R103 Q5 R106 D26 R154 R84 Q45 Q43 R182 R67 Q42 RJ3 Q15 R152 R150 R65 R183 C54 R96 R82 R181 C38 R180 C43 R184 12 Q44 D23 R87 12 C31 R80 Q16 R88 XM-D1000P5 3-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 9 for Common Note on Schematic Diagram and IC Block Diagram. R115 R215 EC61 R112 Q20 R114 R56 Q23 R213 R113 MC11 R19 Q21 D9 Q22 R121 MC28 FET15 MC25 FET14 Q25 D2 R109 FET13 Q19 FET16 R110 BD1 BD2 R116 Q18 R111 LF2 TER1 R211 BD3 BD4 MC22 CF1 Q27 R117 RC3 EC16 RC4 EC17 BD5 MC21 FET20 FET19 PTC2 FET18 FET17 R122 Q31 RC2 EC21 RC1 EC20 MC24 BD6 MC23 Q29 R134 R118 C11 R143 C44 D8 Q30 R145 R147 R148 C48 Q34 MC27 R108 C41 R132 R72 R173 Q10 R105 R131 R151 R128 EC58 R124 ZD5 IC8 Q36 PTC1 MC30 R175 R172 EC13 R123 C8 R146 R107 C40 Q17 R119 R144 C7 R126 R139 R125 Q12 R129 R98 Q35 R133 R130 R86 R83 (Page 12) C22 FUSE1 FET2 FET3 FET4 FET5 FET6 FUSE3 CF9 D12 D19 EC38 EC39 RG5 FET7 FET8 FET9 FET10 FET11 RG8 RG9 RG10 RJ2 MC16 MC20 FET12 MC17 MC18 D21 D22 EC40 EC23 EC37 EC33 RG4 EC24 EC32 RG3 EC25 EC31 RG2 EC26 R137 EC30 RG1 EC27 EC14 CF10 RG6 R101 D13 MC29 FUSE2 LF3 FET1 C34 R71 Q13 PT1 R166 EC22 R127 D20 MC15 MC26 C32 R45 RG11 RG12 RJ1 R58 Q46 R46 RG7 T1 R47 IC B/D 1 R92 1V/DIV, 5µsec/DIV IC6 C33 3.4Vp-p EC15 R93 C19 C42 • Waveform R90 MC12 C37 C18 R302 R91 R202 R102 Q47 R48 15µsec IC6 13 13 5 XM-D1000P5 MEMO 14 14 XM-D1000P5 SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color • Accessories are given in the last of this parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. 4-1. HEAT SINK (MAIN) SECTION 1 2 not supplied (LED board) 3 #2 FUSE3 #1 4 #3 #2 FUSE2 #2 FUSE1 not supplied #1 #1 #1 Ref. No. Part No. Description Remark 1 2 3 4 0 FUSE1 3-253-053-01 3-253-052-01 3-253-054-01 3-253-056-01 1-533-743-11 PLATE, ORNAMENTAL HEAT SINK (MAIN) PLATE, LIGHT GUIDE PANEL (REAR) FUSE (BLADE TYPE) (AUTO FUSE) (40A) Ref. No. Part No. Description Remark 0 FUSE2 0 FUSE3 #1 #2 #3 1-533-743-11 1-533-743-11 7-685-645-79 7-685-549-19 7-685-646-79 FUSE (BLADE TYPE) (AUTO FUSE) (40A) FUSE (BLADE TYPE) (AUTO FUSE) (40A) SCREW +P 3X6 TYPE2 NON-SLIT SCREW +BTP 3X14 TYPE2 N-S SCREW +P 3X8 TYPE2 NON-SLIT 15 XM-D1000P5 4-2. MAIN BOARD SECTION 52 53 not supplied 54 55 53 not supplied not supplied 55 53 54 55 54 #1 56 58 #3 #1 #1 57 #3 51 Ref. No. 51 52 53 54 55 16 Part No. Description 3-253-055-01 A-3274-813-A 3-253-061-01 3-253-062-01 3-225-183-11 PANEL (FRONT) MAIN BOARD, COMPLETE HEAT SINK (SUB) PLATE, RETAINER SCREW (+PSW.TT.3XL) Remark Ref. No. 56 57 58 #1 #3 Part No. Description 3-912-431-01 3-912-432-01 3-253-537-01 7-685-645-79 7-685-646-79 SCREW (+–P) SCREW (+–B) SCREW (M5X11) SCREW +P 3X6 TYPE2 NON-SLIT SCREW +P 3X8 TYPE2 NON-SLIT Remark XM-D1000P5 SECTION 5 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. • CAPACITORS uF : µF • COILS uH : µH LED MAIN The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board. Ref. No. Part No. Description Remark LED BOARD ********** < DIODE > 8-719-060-99 LED SML-210MT-T86 (POWER/PROTECT (POWER)) LED3 8-719-066-99 LED SML-210VT-T86 (POWER/PROTECT (PROTECT)) ************************************************************* Ref. No. Part No. Description C27 C28 C29 C30 C31 1-164-346-11 1-164-346-11 1-164-346-11 1-164-346-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 1uF 1uF 1uF 0.1uF Remark C32 C33 C34 C35 C36 1-163-021-11 1-163-021-11 1-164-005-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 0.47uF 0.1uF 0.1uF 10% 10% C37 C38 C39 C40 C41 1-164-004-11 1-164-004-11 1-163-275-11 1-164-005-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.001uF 0.47uF 0.1uF 10% 10% 5% 10% 25V 25V 50V 25V 25V C42 C43 C44 C48 C50 1-163-021-11 1-164-004-11 1-125-838-11 1-163-019-11 1-163-275-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.1uF 2.2uF 0.0068uF 0.001uF 10% 10% 10% 10% 5% 50V 25V 6.3V 50V 50V C51 C52 C53 C54 CF1 1-163-275-11 1-163-275-11 1-163-275-11 1-164-004-11 1-163-021-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.1uF 0.01uF 5% 5% 5% 10% 10% 50V 50V 50V 25V 50V CF9 CF10 1-164-004-11 CERAMIC CHIP 1-164-004-11 CERAMIC CHIP 0.1uF 0.1uF 10% 10% 25V 25V 10% 16V 16V 16V 16V 25V LED2 A-3274-813-A MAIN BOARD, COMPLETE ********************* 3-253-061-01 HEAT SINK (SUB) 3-253-062-01 PLATE, RETAINER 10% 10% 50V 50V 25V 25V 25V < FERRITE BEAD > BD1 BD2 BD3 BD4 BD5 1-410-396-41 1-410-396-41 1-410-396-41 1-410-396-41 1-410-396-41 INDUCTOR, FERRITE BEAD 0.45uH INDUCTOR, FERRITE BEAD 0.45uH INDUCTOR, FERRITE BEAD 0.45uH INDUCTOR, FERRITE BEAD 0.45uH INDUCTOR, FERRITE BEAD 0.45uH BD6 1-410-396-41 INDUCTOR, FERRITE BEAD 0.45uH < CAPACITOR > C1 C2 C6 C7 C8 1-163-275-11 1-163-275-11 1-164-004-11 1-125-838-11 1-163-017-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.1uF 2.2uF 0.0047uF 5% 5% 10% 10% 5% 50V 50V 25V 6.3V 50V C9 C10 C11 C12 C13 1-164-004-11 1-164-004-11 1-164-005-11 1-164-004-11 1-163-275-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.47uF 0.1uF 0.001uF 10% 10% * CNT1 10% 5% 25V 25V 25V 25V 50V C14 C15 C16 C17 C18 1-164-005-11 1-164-005-11 1-163-275-11 1-117-219-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CERAMIC CHIP 0.47uF 0.47uF 0.001uF 68PF 0.1uF CV3 CV4 5% 5% 10% 25V 25V 50V 1KV 25V C19 C20 C21 C22 C23 1-164-004-11 1-163-235-11 1-163-235-11 1-164-004-11 1-163-275-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 22PF 22PF 0.1uF 0.001uF 10% 5% 5% 10% 5% 25V 50V 50V 25V 50V < CONNECTOR > * CNT2 1-691-785-11 PIN, CONNECTOR (PC BOARD) 4P (HIGH LEVEL INPUT) 1-569-596-11 PLUG, CONNECTOR (2.5mm) 3P < CAPACITOR > 1-126-965-11 ELECT 1-126-965-11 ELECT 22uF 22uF 20% 20% 50V 50V < DIODE > D2 D3 D5 D8 D9 8-719-110-72 8-719-820-05 8-719-801-78 8-719-160-29 8-719-800-76 DIODE DIODE DIODE DIODE DIODE RD30ES-B2 1SS181 1SS184 RD6.2F-B2 1SS226 D11 8-719-800-76 DIODE 1SS226 17 XM-D1000P5 MAIN Ref. No. Part No. Description D12 D13 D15 D16 D19 8-719-987-67 8-719-987-67 8-719-987-67 8-719-987-67 8-719-076-60 DIODE DIODE DIODE DIODE DIODE 11EFS2 11EFS2 11EFS2 11EFS2 FCH20A15 Remark D20 D21 D22 D23 D26 8-719-076-61 8-719-076-60 8-719-076-61 8-719-801-78 8-719-987-63 DIODE DIODE DIODE DIODE DIODE FRH20A15 FCH20A15 FRH20A15 1SS184 1N4148M Ref. No. Part No. Description Remark < TRANSISTOR > < CAPACITOR > FET1 FET2 FET3 FET4 FET5 8-729-056-77 8-729-056-77 8-729-056-77 8-729-056-77 8-729-056-77 FET FET FET FET FET RFP70N06 RFP70N06 RFP70N06 RFP70N06 RFP70N06 FET6 FET7 FET8 FET9 FET10 8-729-056-77 8-729-056-77 8-729-056-77 8-729-056-77 8-729-056-77 FET FET FET FET FET RFP70N06 RFP70N06 RFP70N06 RFP70N06 RFP70N06 EC1 EC2 EC3 EC4 EC5 1-128-582-11 1-128-582-11 1-126-965-11 1-126-965-11 1-126-965-11 ELECT ELECT ELECT ELECT ELECT 10uF 10uF 22uF 22uF 22uF 20% 20% 20% 20% 20% 63V 63V 50V 50V 50V FET11 FET12 FET13 FET14 FET15 8-729-056-77 8-729-056-77 8-729-056-78 8-729-056-78 8-729-056-78 FET FET FET FET FET RFP70N06 RFP70N06 SSP45N20A SSP45N20A SSP45N20A EC6 EC7 EC8 EC9 EC10 1-126-965-11 1-126-965-11 1-126-965-11 1-104-666-11 1-104-666-11 ELECT ELECT ELECT ELECT ELECT 22uF 22uF 22uF 220uF 220uF 20% 20% 20% 20% 20% 50V 50V 50V 25V 25V FET16 FET17 FET18 FET19 FET20 8-729-056-78 8-729-056-78 8-729-056-78 8-729-056-78 8-729-056-78 FET FET FET FET FET SSP45N20A SSP45N20A SSP45N20A SSP45N20A SSP45N20A EC11 EC12 EC13 EC14 EC15 1-128-582-11 1-126-965-11 1-126-965-11 1-128-149-11 1-128-339-11 ELECT ELECT ELECT ELECT ELECT 10uF 22uF 22uF 100uF 2200uF 20% 20% 20% 20% 20% 63V 50V 50V 160V 16V EC16 EC17 EC20 EC21 EC22 1-107-947-11 1-107-947-11 1-107-947-11 1-107-947-11 1-115-814-11 ELECT ELECT ELECT ELECT ELECT 220uF 220uF 220uF 220uF 0.001F 20% 20% 20% 20% 20% 160V 160V 160V 160V 35V EC23 EC24 EC25 EC26 EC27 1-115-814-11 1-115-814-11 1-115-814-11 1-115-814-11 1-115-814-11 ELECT ELECT ELECT ELECT ELECT 0.001F 0.001F 0.001F 0.001F 0.001F 20% 20% 20% 20% 20% 35V 35V 35V 35V 35V EC28 EC29 EC30 EC31 EC32 1-126-951-11 1-126-951-11 1-100-587-11 1-100-587-11 1-100-587-11 ELECT ELECT ELECT ELECT ELECT 470uF 470uF 1000uF 1000uF 1000uF 20% 20% 35V 35V 100V 100V 100V EC33 EC37 EC38 EC39 EC40 1-100-587-11 1-100-587-11 1-100-587-11 1-100-587-11 1-100-587-11 ELECT ELECT ELECT ELECT ELECT 1000uF 1000uF 1000uF 1000uF 1000uF EC50 EC51 EC52 EC53 EC54 1-126-934-11 1-126-965-11 1-126-965-11 1-126-963-11 1-128-582-11 ELECT ELECT ELECT ELECT ELECT 220uF 22uF 22uF 4.7uF 10uF 20% 20% 20% 20% 20% 16V 50V 50V 50V 63V EC55 EC56 EC58 EC61 1-128-582-11 1-104-665-11 1-104-665-11 1-126-966-11 ELECT ELECT ELECT ELECT 10uF 100uF 100uF 33uF 20% 20% 20% 20% 63V 25V 25V 16V 18 100V 100V 100V 100V 100V < FUSE > 0 FUSE1 0 FUSE2 0 FUSE3 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) < IC > IC1 IC2 IC4 IC5 IC6 8-759-394-81 8-759-394-81 8-759-394-81 8-759-700-94 8-759-904-94 IC IC IC IC IC NJM4559M-TE2 NJM4559M-TE2 NJM4559M-TE2 NJM5532M TL494CN IC7 IC8 IC9 8-759-085-67 IC LM339NS 8-759-980-04 IC LM311PS 8-759-394-81 IC NJM4559M-TE2 < JACK > JK1 1-779-078-41 JACK, PIN 4P (INPUT,OUTPUT (THROUGH)) < COIL > LF2 LF3 1-424-885-11 COIL, CHOKE 1-424-884-11 COIL, CHOKE 230uH 11.3uH < CAPACITOR > MC3 MC4 MC5 MC6 MC7 1-137-401-11 1-137-401-11 1-130-777-00 1-137-401-11 1-130-777-00 MYLAR MYLAR MYLAR MYLAR MYLAR 0.22uF 0.22uF 0.1uF 0.22uF 0.1uF 5% 5% 5% 5% 5% 100V 100V 100V 100V 100V MC9 MC10 MC11 MC12 MC15 1-130-777-00 1-130-777-00 1-137-401-11 1-137-391-11 1-137-350-11 MYLAR MYLAR MYLAR MYLAR MYLAR 0.1uF 0.1uF 0.22uF 0.0047uF 0.015uF 5% 5% 5% 5% 5% 100V 100V 100V 100V 100V MC16 MC17 1-130-777-00 MYLAR 1-130-777-00 MYLAR 0.1uF 0.1uF 5% 5% 100V 100V The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. XM-D1000P5 MAIN Ref. No. Part No. Description MC18 MC19 MC20 MC21 MC22 1-136-175-00 1-137-351-11 1-137-352-11 1-137-401-11 1-137-401-11 FILM MYLAR MYLAR MYLAR MYLAR 0.68uF 0.022uF 0.033uF 0.22uF 0.22uF 5% 5% 5% 5% 5% 50V 100V 100V 100V 100V Remark MC23 MC24 MC25 MC26 MC27 1-137-401-11 1-137-401-11 1-137-398-11 1-107-357-11 1-104-987-11 MYLAR MYLAR MYLAR MYLAR MYLAR 0.22uF 0.22uF 0.068uF 0.47uF 0.001uF 5% 5% 5% 5% 5% 100V 100V 100V 100V 100V MC28 MC29 MC30 MC31 1-104-987-11 1-136-137-00 1-164-303-11 1-102-074-00 MYLAR FILM CERAMIC CERAMIC 0.001uF 1uF 0.1uF 0.001uF 5% 5% 100V 50V 25V 50V Ref. No. Q44 Q45 Q46 Q47 Part No. Description 8-729-034-50 8-729-034-51 6-500-660-01 6-500-660-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Remark KTA1504 KTC3875 KTC3206 KTC3206 < RESISTOR > 10% < TRANSFORMER > PT1 1-439-759-11 TRANSFORMER, DC-DC CONVERTER < PHOTO COUPLER > PTC1 PTC2 8-719-902-56 PHOTO COUPLER PC817 8-719-902-56 PHOTO COUPLER PC817 < TRANSISTOR > Q1 Q2 Q3 Q4 Q5 8-729-931-36 8-729-056-82 8-729-931-36 8-729-056-82 8-729-034-50 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR MPSA42 MPSA92 MPSA42 MPSA92 KTA1504 Q6 Q7 Q8 Q9 Q10 8-729-034-50 8-729-034-51 8-729-034-51 8-729-034-51 8-729-034-51 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTA1504 KTC3875 KTC3875 KTC3875 KTC3875 Q11 Q12 Q13 Q14 Q15 8-729-034-50 8-729-040-76 8-729-034-51 8-729-034-51 8-729-034-51 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTA1504 KTA1273-Y-AT KTC3875 KTC3875 KTC3875 Q16 Q17 Q18 Q19 Q20 8-729-034-51 8-729-034-51 6-500-660-01 6-500-660-01 8-729-056-82 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC3875 KTC3875 KTC3206 KTC3206 MPSA92 Q21 Q22 Q23 Q25 Q27 6-550-247-01 8-729-056-79 8-729-053-87 6-550-247-01 8-729-053-87 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTA1659A 2N5401 KTC4370A KTA1659A KTC4370A Q29 Q30 Q31 Q34 Q35 6-550-247-01 8-729-053-87 8-729-056-79 8-729-038-53 8-729-034-50 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTA1659A KTC4370A 2N5401 KRA101S KTA1504 Q36 Q37 Q39 Q42 Q43 8-729-034-51 8-729-034-51 8-729-034-50 8-729-034-51 8-729-034-51 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC3875 KTC3875 KTA1504 KTC3875 KTC3875 R1 R2 R3 R4 R5 1-216-081-00 1-216-081-00 1-216-073-00 1-216-073-00 1-216-049-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 22K 10K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R6 R7 R8 R10 R11 1-216-093-00 1-216-093-00 1-216-049-11 1-216-206-00 1-216-206-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 68K 68K 1K 2.2K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/8W 1/8W R12 R13 R14 R15 R16 1-216-089-00 1-216-061-00 1-216-053-00 1-216-045-00 1-216-081-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 3.3K 1.5K 680 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R17 R18 R19 R20 R23 1-216-049-11 1-216-049-11 1-216-105-00 1-216-057-00 1-216-057-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 220K 2.2K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R24 R25 R26 R27 R28 1-216-057-00 1-216-057-00 1-216-057-00 1-216-083-00 1-216-057-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 2.2K 2.2K 27K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R29 R43 R45 R46 R47 1-216-049-11 1-216-061-00 1-216-190-00 1-216-222-00 1-216-190-00 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 1K 3.3K 470 10K 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/8W 1/8W 1/8W R48 R50 R51 R52 R53 1-216-222-00 1-216-061-00 1-216-061-00 1-216-061-00 1-216-049-11 RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 3.3K 3.3K 3.3K 1K 5% 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/10W 1/10W R54 R55 R56 R57 R58 1-216-073-00 1-216-073-00 1-216-021-00 1-216-077-00 1-216-198-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 68 15K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/8W R59 R60 R61 R62 R63 1-216-037-00 1-216-075-00 1-216-049-11 1-216-049-11 1-216-081-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330 12K 1K 1K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R64 R65 R66 R67 R68 1-216-073-00 1-208-529-61 1-216-073-00 1-216-065-00 1-216-089-00 METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 10K 62K 10K 4.7K 47K 5% 2% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R69 R70 1-216-117-00 METAL CHIP 1-208-813-11 RES-CHIP 680K 20K 5% 2% 1/10W 1/10W 19 XM-D1000P5 MAIN Ref. No. Part No. Description Part No. Description R71 R72 R73 R74 R75 1-216-073-00 1-216-049-11 1-216-089-00 1-216-061-00 1-216-061-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 1K 47K 3.3K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R136 R137 R139 R143 R144 1-216-067-00 1-216-899-11 1-216-897-11 1-207-612-00 1-207-612-00 METAL CHIP METAL OXIDE METAL OXIDE WIREWOUND WIREWOUND 5.6K 15K 6.8K 0.1 0.1 5% 5% 5% 10% 10% 1/10W 2W 2W 3W 3W R76 R77 R78 R79 R80 1-216-049-11 1-216-073-00 1-216-063-00 1-216-073-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 3.9K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R145 R146 R147 R148 R149 1-207-612-00 1-207-612-00 1-207-612-00 1-207-612-00 1-216-089-00 WIREWOUND WIREWOUND WIREWOUND WIREWOUND METAL CHIP 0.1 0.1 0.1 0.1 47K 10% 10% 10% 10% 5% 3W 3W 3W 3W 1/10W R81 R82 R83 R84 R85 1-216-089-00 1-216-089-00 1-216-198-00 1-216-049-11 1-208-775-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 47K 47K 1K 1K 510 5% 5% 5% 5% 2% 1/10W 1/10W 1/8W 1/10W 1/10W R150 R151 R152 R154 R155 1-216-049-11 1-216-089-00 1-216-049-11 1-216-081-00 1-216-061-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 47K 1K 22K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R86 R87 R88 R90 R91 1-216-073-00 1-216-073-00 1-208-813-11 1-216-073-00 1-216-073-00 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 10K 10K 20K 10K 10K 5% 5% 2% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R156 R157 R158 R159 R163 1-216-081-00 1-216-081-00 1-216-073-00 1-216-073-00 1-216-093-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 22K 10K 10K 68K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R92 R93 R96 R97 R98 1-208-789-11 1-260-106-11 1-216-065-00 1-216-035-00 1-216-073-00 RES-CHIP CARBON METAL CHIP METAL CHIP METAL CHIP 2K 3.9K 4.7K 270 10K 2% 5% 5% 5% 5% 1/10W 1/2W 1/10W 1/10W 1/10W R164 R166 R169 R170 R171 1-216-093-00 1-216-073-00 1-216-029-00 1-216-073-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 68K 10K 150 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R101 R102 R103 R104 R105 1-215-880-11 1-216-206-00 1-216-037-00 1-216-045-00 1-216-089-00 METAL OXIDE RES-CHIP METAL CHIP METAL CHIP METAL CHIP 10 2.2K 330 680 47K 5% 5% 5% 5% 5% 2W F 1/8W 1/10W 1/10W 1/10W R172 R173 R174 R175 R180 1-216-121-00 1-216-113-00 1-216-065-00 1-216-073-00 1-216-065-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1M 470K 4.7K 10K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R106 R107 R108 R109 R110 1-216-043-00 1-216-097-00 1-216-065-00 1-216-648-11 1-216-009-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 560 100K 4.7K 3K 22 5% 5% 5% 2% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R181 R182 R183 R184 R202 1-216-065-00 1-216-081-00 1-216-065-00 1-216-073-00 1-216-206-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 4.7K 22K 4.7K 10K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/8W R111 R112 R113 R114 R115 1-216-166-00 1-216-246-00 1-208-473-11 1-216-190-00 1-216-196-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 47 100K 300 470 820 5% 5% 2% 5% 5% 1/8W 1/8W 1/8W 1/8W 1/8W R211 R213 R215 R302 RC1 1-216-164-00 1-208-473-11 1-216-200-11 1-216-206-00 1-216-238-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 39 300 1.2K 2.2K 47K 5% 2% 5% 5% 5% 1/8W 1/8W 1/8W 1/8W 1/8W R116 R117 R118 R119 R121 1-216-198-00 1-216-198-00 1-216-198-00 1-216-194-00 1-260-094-11 METAL CHIP METAL CHIP METAL CHIP RES-CHIP CARBON 1K 1K 1K 680 390 5% 5% 5% 5% 5% 1/8W 1/8W 1/8W 1/8W 1/2W RC2 RC3 RC4 RG1 RG2 1-216-238-00 1-216-238-00 1-216-238-00 1-247-807-31 1-247-807-31 RES-CHIP RES-CHIP RES-CHIP CARBON CARBON 47K 47K 47K 100 100 5% 5% 5% 5% 5% 1/8W 1/8W 1/8W 1/4W 1/4W R122 R123 R124 R125 R126 1-260-094-11 1-216-097-00 1-215-897-11 1-216-073-00 1-216-057-00 CARBON METAL CHIP METAL OXIDE METAL CHIP METAL CHIP 390 100K 6.8K 10K 2.2K 5% 5% 5% 5% 5% 1/2W 1/10W 2W F 1/10W 1/10W RG3 RG4 RG5 RG6 RG7 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON 100 100 100 100 100 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R127 R128 R129 R130 R131 1-216-089-00 1-216-073-00 1-216-087-00 1-208-789-11 1-216-107-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 47K 10K 39K 2K 270K 5% 5% 5% 2% 5% 1/10W 1/10W 1/10W 1/10W 1/10W RG8 RG9 RG10 RG11 RG12 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON 100 100 100 100 100 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R132 R133 R134 1-216-049-11 METAL CHIP 1-216-121-00 METAL CHIP 1-216-073-00 METAL CHIP 1K 1M 10K 5% 5% 5% 1/10W 1/10W 1/10W RS1 RS2 RS5 1-216-073-00 METAL CHIP 1-216-073-00 METAL CHIP 1-216-295-00 METAL CHIP 10K 10K 0 5% 5% 5% 1/10W 1/10W 1/10W 20 Remark Ref. No. Remark F F F F F F F F XM-D1000P5 MAIN Ref. No. RV9 Part No. Description 1-216-295-00 METAL CHIP Remark 0 5% Ref. No. 1/10W Part No. Description Remark PARTS FOR INSTALLATION AND CONNECTIONS *************************************** < TRANSFORMER > 101 T1 < TERMINAL BOARD > TER1 3-367-410-11 SCREW (DIA.5X15), TAPPING (MOUNTING SCREW) 1-690-779-31 CORD (WITH CONNECTOR) (0.2m) 3-253-088-01 COVER (POWER) 1-437-469-11 TRANSFORMER, PULSE 1-780-008-21 TERMINAL BOARD (7P+FUSE) (REM,+12V,GND, SPEAKER OUT) 102 103 101 102 103 < THERMISTOR > THR1 THR2 THR3 1-804-497-11 THERMISTOR, CHIP 1-810-920-11 THERMISTOR 1-804-497-11 THERMISTOR, CHIP φ 5 × 15 (× 5) 0.2 m < VARIABLE RESISTOR > VR1 VR2 VR3 1-227-589-11 RES, VAR, CARBON 5KX2 (LEVEL) 1-227-590-11 RES, VAR, CARBON 5KX2 (LOW BOOST (40Hz)) 1-227-576-11 RES, VAR, CARBON 20KX2 (LPF) < DIODE > ZD1 ZD2 ZD3 ZD4 ZD5 8-719-069-69 8-719-069-69 8-719-069-69 8-719-069-69 8-719-069-69 DIODE DIODE DIODE DIODE DIODE RD18F-T7B RD18F-T7B RD18F-T7B RD18F-T7B RD18F-T7B ZD6 8-719-109-86 DIODE RD5.1ES-B3 ************************************************************* MISCELLANEOUS *************** 0 FUSE1 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) 0 FUSE2 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) 0 FUSE3 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) ************************************************************* ACCESSORIES ************ 3-251-200-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH) 3-251-200-21 MANUAL, INSTRUCTION (GERMAN,ITALIAN) (AEP,UK,E) 3-251-200-31 MANUAL, INSTRUCTION (SPANISH, TRADITIONAL CHINESE) (AEP,UK,E) 3-251-200-41 MANUAL, INSTRUCTION (PORTUGUESE,DUTCH) (AEP,UK,E) 3-251-200-51 MANUAL, INSTRUCTION (SWEDISH,POLISH) (AEP,UK,E) 3-251-200-61 MANUAL, INSTRUCTION (GREEK,RUSSIAN) (AEP,UK,E) ************************************************************* The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. 21 XM-D1000P5 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. 1.0 22 Date 2003. 02 Description of Revision New