Transcript
XONE 464
10 output desk / rack mount professional club mixer
When we decided to build a club mixer, we wanted to satisfy club techs and DJs alike. Xone:464 naturally shares its construction methods with our pro touring desks, so venues can depend on it for outstanding audio and reliability. Its unique analogue filters and 4 band asymmetric EQ also make it an incredibly creative tool that DJs really enjoy using. We also included a set of 4 fully featured mic/line inputs, which is great for venues running small live sets as well as DJs, or for those pioneering artists who are mixing live and recorded sources.
FEATURES: 4 Mono Inputs
XLR or TRS jack connector, gain, 4 band EQ with swept mids, HPF @ 100Hz, 6 aux sends (1-4 pre, 5&6 switchable pre/post fader), pan, peak signal led, cue and on button with led. 100mm long throw fader. Insert point and direct output on TRS jack
6 Dual Stereo Channels
2 stereo sources (A & B) per channel. A is on RCA for all channels with RIAA preamps on CH 5,6,9,10. B inputs are line in on RCA CH 5 & 10 and TRS on CH 6,7, 8 & 9. Access to all 6 auxes is at the top of the channels, leaving performance area clear. 3 colour bar meter and gain control. Powerful 4 band EQ with on switch. 60mm fader and X-fade assign section
Stereo Mix Outputs
2 independent mix outputs with level controls, 12 segment 3 colour led metering and insert. Balanced XLR plus secondary RCA outputs, plus selectable mono out also on XLR and TRS. CH1-4 feed mix1 or mix2. Stereo channels feed mix1 direct or via the X-fader. Mix1 can route to mix2
6 Auxiliary Sends
6 aux sends to [TRS] outputs for monitors or FX sends. Mic / line CH 1-4 have individual sends and stereo CH 5-10 have aux 1&2 individual mono sum and auxes 3&4, 5&6 paired with L to odd, R to even. Aux sends 1-4 are always prefade, while auxes 5&6 are switchable pre/post fader. Additional controls allow aux sends to track the X-fader post fade
4 Stereo 2 Mono Zone Outs
Mix1, mix2, post x-fader aux 3&4 and 5&6 can provide stereo mixes on rotary controls. Post x-fader aux 1 & aux 2 can provide mono mix outputs with level controls
4 Band EQ
Mono channels have 2 swept frequency mids. Stereo channels have EQ-on switch and all frequency sections have +6dB boost to preserve headroom and -26dB cut for creative mixing
VCA Cross Fader
Conductive plastic, high quality 45mm Penny & Giles fader with curve switchable to cut or dip. Stereo channels can be assigned to X (left) side with green led indication or Y (right) side with yellow led. VCA operation means wear and tear does not affect audio. Drop-in replacements. Pan trim control for imbalance
Voltage Controlled Filters
2 filters [1 for each side of the x-fader] with choice of High Pass, Band Pass, Low Pass or multiples e.g. notch. Resonance control - adjusts Q from ‘mild to wild’. Sweep controls from 100Hz to 20kHz with blue led on switch
External Input Engineer / DJ's Toolbox
PSU Configuration Options
26
TRS jack inputs via level control to mix1, mix2 or monitor 2 high powered headphone outputs with level. Booth output on TRS with level. Monitor section has 8-way switch bank to select monitor source. 12 segment 3 colour bar metering. Channel cue overrides the monitor selected in the phones [and booth if Cue Enable is pressed]. Split Cue sends cue signals to left and selected program to right. Mute kills local monitor output [option for -20dB action]. Mono sum button for phase and compatibility check High performance internal switched-mode power supply. Universal mains input voltage Internal links: mono CH aux sends to pre-EQ and / or pre-ON. Stereo CH Cue to post EQ. Stereo CH auxes to pre-EQ. Direct out to pre-fade. EXT in -10dBV/+4dBu. Monitor Mute to -20dB attenuator. Remote local monitor mute
XONE 464 Technical Specifications OdBu = 0.775 Volts rms OdBu = 1 Volt rms
+4dBu = 1.23V rms -10dBV = 316mV rms
Maximum output level XLR TRS jack RCA phono
+26dBu into >2k ohm load +21dBu into >2k ohm load +15dBu into >10k ohm load
Internal headroom Channels Mix to output
+21dB +23dB
Peak indicators Turn on 9 dB before clipping Meters MIX 1.2/MONITOR Peak reading 12 led 3 colour Frequency response 20Hz to 40kHz
+0/-1dB
Distortion THD+noise measured at +14dBu 1kHz < 0.006% Crosstalk Channel shutoff measured at 1kHz < 90dB Noise measured rms 22Hz to 22kHz MIC EIN
-128dB referred to 150 ohm source
Residual output noise XLR TRS jack L RCA phono
-90dBu (-94dB S/N) -84dBu (-84dB S/N) -92dBu (-84dB S/N)
Mix noise, ch routed XLR TRS jack RCA phono
-86dBu (-90dB S/N) -83dBu (-83dB S/N) -91dBu (-83dB S/N)
Power Supply Internal switch mode power unit with auto sensing mains input. MAINS IN socket Power lead AC mains Consumption Mains fuse rating
IEC 3 pin Country dependent with moulded mains plug supplied 100 to 240V AC @ 50/60Hz 30W max 100-240V AC T500mA 20mm
Mechanical specifications The connector pod can be rotated and fixed in one of two positions to allow either desktop operation with rear facing connectors, or 19” rack mounting with underside connectors in 10U space. Width
Height
Depth
Desktop Rack mounted Packed
483 mm (19”) 192 mm (7.6”) 530 mm(20.9”) 483 mm (19”) 444 mm (17.5”) 135 mm (5.3”) 590 mm (23.2”) 260 mm (10.2”) 610 mm (24”) Unpacked
Packed
Weight
10kg (22lb)
13kg (28lb)
Connections INPUT CH 1-4 IN (XLR) PAD out PAD in CH 1-4 IN (TRS) CH 5,6,9,10 IN A CH 7,8 IN A CH 5,10 IN B CH 6,7,8,9 IN B EXT IN
Balanced XLR female Balanced TRS jack RCA phono RIAA RCA phono RCA phono Balanced TRS jack Balanced TRS jack
INSERTS CH 1-4
Unbalanced TRS jack
MIX OUT 1,2
Unbalanced TRS jack
2k ohm >10k ohm >10k ohm 47k ohm >10k ohm >15k ohm >10k ohm >10k ohm
SEND RETURN SEND RETURN
-60 to -20dBu -30 to +10dBu -30 to +10dBu 2 to 100mV -10 to +10dBu -10 to +10dBu -10 to +10dBu -10dBV (+4dBu option)
<75 ohm >3k ohm <75 ohm >7k ohm
0dBu
OUTPUT DIR OUT 1-4 MIX OUT 1,2 (XLR) MIX OUT 2 (RCA) MONO OUT (XLR) MONO OUT (TRS) AUX OUT 1-6 LOCAL MONITOR OUT HEADPHONES 1,2
TRS jack XLR male RCA phono XLR male TRS jack TRS jack TRS jack
XLR connections are TRS input and output connections are TRS insert connections are
Impedance balanced Balanced
<75 ohm 0dBu <75 ohm +4dBu <75 ohm -10dBV Balanced <75 ohm +4dBu Impedance balanced <75 ohm -2dBu Impedance balanced <75 ohm -2dBu Impedance balanced <75 ohm -2dB Tip=L Ring=R 30 to 600 ohm recommended Pin 2=hot(+) Pin 3=cold(-) Pin 1=GND Tip=hot(+) Ring=cold(-) Sleeve=GND Tip=SEND Ring=RETURN Sleeve=GND
-2dBu
block diagrams, user guides, brochures & more:
/Xone464.asp
27
