Yamaha | Rx-v396 | Owner's Manual | Yamaha Rx-v396 Owner's Manual

Transcript

UCA RX-V396 Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER’S MANUAL MODE D’EMPLOI 30 1/20/0, 4:57 PM SAFETY INSTRUCTIONS 8 Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9 Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 1 Read Instructions – All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions – The safety and operating instructions should be retained for future reference. 3 Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. 4 Follow Instructions – All operating and other instructions should be followed. 5 6 Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 10 Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12 Cleaning – The unit should be cleaned only as recommended by the manufacturer. 13 Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines – An outdoor antenna should be located away from power lines. 18 Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. CAUTION 0101V396caution_EN(UCA) 2 1/11/0, 5:28 PM SAFETY INSTRUCTIONS MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE PREPARATION Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING INTRODUCTION 19 For US customers only: Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. FCC INFORMATION (for US customers only) Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/ s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. APPENDIX The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. ADVANCED OPERATION This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: BASIC OPERATION 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. We Want You Listening For A Lifetime Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. English YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. CAUTION 0101V396caution_EN(UCA) 3 1/11/0, 5:28 PM CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 12. To prevent lightning damage, disconnect the AC power cord and disconnect the antenna cable when there is an electrical storm. 2. Install this unit in a cool, dry, clean place — away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 13. Grounding or polarization — Precautions should be taken so that the grounding or polarization of the unit is not defeated. 3. Never open the cabinet. If something drops into the unit, contact your dealer. 14. AC outlet — Do not connect audio component to the AC outlet on the rear panel if that component requires more power than the outlet is rated to provide. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power cord and then the wires connected to other component. Never pull the wires themselves. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. 5. The openings on the cover assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the unit will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in a well-ventilated area to prevent fire and damage. IMPORTANT Please record the serial number of this unit in the space below. 6. The voltage used must be the same as that specified on this unit. Using this unit with a higher voltage than specified is dangerous and may result in fire or other accidents. YAMAHA will not be held responsible for any damage resulting from the use of this unit with a voltage other than that specified. 7. Digital signals generated by this unit may interfere with other component such as tuners, receivers and TVs. Move this unit farther away from such component if interference is observed. 8. Always set VOLUME to the “m” position before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started. 9. Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. 10. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. 11. When not planning to use this unit for a long period of time (e.g., a vacation), disconnect the AC power cord from the wall outlet. CAUTION 0101V396caution_EN(UCA) 4 1/11/0, 5:28 PM INTRODUCTION FEATURES CONTENTS 5-Channel Power Amplification INTRODUCTION FEATURES .................................................................. 1 CONTENTS ................................................................. 1 GETTING STARTED ................................................. 2 CONTROLS AND FUNCTIONS ............................... 4 Multi-mode Digital Sound Field Processing Digital Sound Field Processor (DSP) Dolby Digital Decoder Dolby Pro Logic Decoder CINEMA DSP: Theater-like Sound Experience by the Combination of YAMAHA DSP Technology and Dolby Digital or Dolby Pro Logic ◆ Automatic Input Balance Control for Dolby Pro Logic decoding PREPARATION SPEAKER SETUP ....................................................... 8 CONNECTIONS .......................................................... 9 ADJUSTING THE SPEAKER BALANCE ............ 17 PREPARATION ◆ ◆ ◆ ◆ INTRODUCTION ◆ Minimum RMS Output (0.06% THD, 20 Hz – 20 kHz) Main: 60 W + 60 W (8 Ω) Center: 60 W (8 Ω) Rear: 60 W + 60 W (8 Ω) Sophisticated FM/AM Tuner Other Features PLAYING A SOURCE .............................................. 19 DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT .................................................................. 22 SOUND FIELD PROGRAM .................................... 23 TUNING ..................................................................... 26 RECORDING A SOURCE ON TAPE, MD OR VIDEO CASSETTE ............................................... 30 ADVANCED OPERATION SET MENU ................................................................. 31 DELAY TIME AND SPEAKER OUTPUT LEVELS ................................................. 35 SLEEP TIMER .......................................................... 37 PRESET REMOTE CONTROL .............................. 38 TROUBLESHOOTING ............................................ 45 SPECIFICATIONS .................................................... 48 GLOSSARY ................................................................ 49 INDEX ........................................................................ 50 y indicates a tip for your operation. English Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992 – 1997 Dolby Laboratories, Inc. All rights reserved. 1 0102V39601-07_EN(UCA) 1 1/11/0, 5:28 PM APPENDIX APPENDIX ADVANCED OPERATION ◆ “SET MENU” which Provides You with 10 Items for Optimizing This Unit for Your Audio/Video System ◆ Test Tone Generator for Easier Speaker Balance Adjustment ◆ 6-Channel External Decoder Input for Other Future Formats ◆ 2 Optical/1 Coaxial Digital Signal Input Terminals ◆ SLEEP Timer ◆ Remote Control with Preset Manufacturer Codes BASIC OPERATION BASIC OPERATION ◆ 40-Station Random Access Preset Tuning ◆ Automatic Preset Tuning ◆ Preset Station Shifting Capability (Preset Editing) GETTING STARTED Checking the Package Contents Check that the following items are included in your package. Remote control Batteries (AAA, R03, UM-4 type) Antenna adapter (U.S.A. and Canada models only) Indoor FM antenna Quick reference card AM loop antenna Connection guide Battery Installation in the Remote Control Battery Replacement If the remote control operates only when it is close to the unit, the batteries are weak. Replace all the batteries with new ones. Be sure to replace the batteries within about two minutes. If it takes longer than two minutes, the codes preset for the remote control will return to the factory settings. (Refer to pages 38 to 44 about the remote control.) 2 1 3 Notes 1 Turn the remote control over and slide the battery compartment cover in the direction of the arrow. 2 Insert the batteries (AAA, R03 or UM-4 type) according the polarity markings on the inside of the battery compartment. 3 Close the battery compartment cover. • Use only AAA, R03 or UM-4 batteries for replacement. • Be sure the battery polarity is correct. (See the illustration inside the battery compartment.) • Remove the batteries if the remote control will not be used for an extended period of time. • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 2 0102V39601-07_EN(UCA) 2 1/14/0, 8:29 AM GETTING STARTED Using the Remote Control Within approximately 6 m (20 feet) INTRODUCTION Remote control sensor The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the infrared sensor during operation. When the sensor is covered or there is a large object between the remote control and the sensor, the sensor cannot receive signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a fluorescent or strobe light). In this case, change the direction of the light or reposition the unit to avoid direct lighting. Notes Handle the remote control with care. Do not spill water, tea or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following conditions: – high humidity or temperature such as near a heater, stove or bath; – dusty places; or – extremely low temperature. PREPARATION • • • • BASIC OPERATION ADVANCED OPERATION APPENDIX English 3 0102V39601-07_EN(UCA) 3 1/11/0, 5:28 PM CONTROLS AND FUNCTIONS Front Panel 1 2 3 – 7 8 90 + – q 4 + L 5 6 R w e r t y u i o 1 STANDBY/ON 6 VOLUME Press this switch to turn on the power of this unit or to set this unit in the standby mode. Before turning the power on, set VOLUME to the “m” position. Turn this control to turn up or down the volume. Standby mode In this mode, this unit consumes a very small quantity of power to receive infrared-signals from the remote control. 2 Remote control sensor 7 PHONES jack Connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through the headphones. When using headphones only, set both SPEAKERS A and B to the OFF position and press EFFECT to turn off the effect speakers (center and rear) (so that no DSP program indicator lights up on the display). This receives signals from the remote control. 8 SPEAKERS 3 Display Set A or B (or both A and B) to the ON position for the main speaker system (connected to this unit) that you want to use. Set the button(s) to the OFF position for the main speaker system that you don’t want to use. This shows various information. (Refer to page 6 for details.) 4 INPUT MODE Press this button to select the input mode between AUTO and ANALOG for the DVD/LD, TV/digital TV and satellite tuner sources. 5 INPUT Turn this selector to select the input source (VCR, SAT/DTV, DVD/LD, TUNER, CD, AUX) that you want to listen to or watch. The name of the selected input source appears on the display. 9 PROGRAM selector Press l or h to select a DSP program when the effect speakers (center and rear) are turned on. The selected program indicator lights up on the display. 0 EFFECT Press this button to turn on or off the effect speakers (center and rear). If you turn them off, all Dolby Digital audio signals are directed to the right and left main speakers. In that case, the output levels of the right and left speakers may not match. 4 0102V39601-07_EN(UCA) 4 1/20/0, 11:28 AM CONTROLS AND FUNCTIONS t PRESET/TUNING These controls are only effective for the sound from the main speakers. a) BASS Turn this control clockwise to increase or counterclockwise to decrease the low-frequency response. The “0” position produces a flat response. b) TREBLE Turn this control clockwise to increase or counterclockwise to decrease the high-frequency response. The “0” position produces a flat response. When “ z ” appears This button is used to select a preset station number (1 to 8). Press h to select a higher and l to select a lower preset station number. When “ z ” goes off This button is used for tuning. Press h to tune in to higher frequencies, and l to tune in to lower frequencies. w TAPE/MD MON / EXT. DECODER Press this button to turn on or off “ z ” on the display and switch the function between for storing a broadcasting station (preset tuning) and for tuning. This button is also used to exchange the assignment of two preset stations with each other. u FM/AM Press this button to switch the reception band between FM and AM. i MEMORY (MAN’L/AUTO FM) e BALANCE r A/B/C/D/E Press this button to select one of a group (A to E) of preset stations. Press this button to store the broadcasting stations. Hold down this button for more than three seconds to begin automatic preset tuning. o TUNING MODE (AUTO/MAN’L MONO) Press this button to switch the tuning mode between automatic and manual. To use the automatic tuning method, press this button so that the “AUTO” indicator lights up on the display. To use the manual tuning method, press this button so that the “AUTO” indicator goes off. BASIC OPERATION This control is only effective for the sound from the main speakers. Turn the control to adjust the balance of the output volume from the right and left main speakers to compensate for sound imbalance caused by the speaker location or listening room conditions. PREPARATION Press this button to select a tape or an MD source. The “TAPE/MD MONITOR” indicator lights up on the display. When you press the button next, the “TAPE/MD MONITOR” indicator goes off, “EXT. DECODER” appears on the display and you can listen to a source connected to the EXTERNAL DECODER INPUT terminals. y PRESET/TUNING, EDIT INTRODUCTION q Tone controls ADVANCED OPERATION APPENDIX English 5 0102V39601-07_EN(UCA) 5 1/11/0, 5:28 PM CONTROLS AND FUNCTIONS Display 1 2 6 7 4 5 3 8 9 0 1 g and o indicators 6 x indicator “ g ” lights up when the built-in Dolby Digital decoder is on and the signals of the selected source are encoded with Dolby Digital. “ o ” lights up when the built-in Dolby Pro Logic decoder is on. “ x ” lights up when the built-in digital sound field processor is on. 7 MEMORY indicator The name of the selected DSP program lights up. This flashes for about five seconds after pressing MEMORY. During this period, the displayed station can be stored in the memory. 3 Multi-information display 8 AUTO indicator This display shows various information: for example the name of the selected input source and the various settings during adjustment with the SET MENU. The current station frequency and band (FM or AM) also appear when the tuner is selected as the input source. This lights up when the unit is in the automatic tuning mode. 2 DSP program indicators 4 SLEEP indicator This lights up while the built-in SLEEP timer is on. 5 TAPE/MD MONITOR indicator This lights up when the tape deck or MD recorder, etc. is selected as the input source by pressing TAPE/MD MON / EXT. DECODER (or TAPE/MD). 9 STEREO indicator This lights up when an FM stereo broadcast with sufficient signal strength is being received. 0 Signal-level indicator This indicates the signal level of the station being received. If multipath interference is detected, the indication decreases. 6 0102V39601-07_EN(UCA) 6 2/10/0, 11:23 AM CONTROLS AND FUNCTIONS Remote Control 3 POWER Each time you press this button, the unit switches between the power on and standby mode. INTRODUCTION This section describes basic operation of this unit with the remote control. First, press AMP(TUNER) on the component selector. Refer to “PRESET REMOTE CONTROL” on page 38 for full details. 4 TEST Press this button to output the test tone for each speaker. 1 5 A/B/C/D/E, PRESET +/– Press AMP(TUNER). 2 3 These buttons are used to select a preset station. A/B/C/D/E: To select one of a group (A to E) of preset stations PRESET +/–: To select a preset station number (1 to 8) PREPARATION 6 MUTE Press this button to mute the sound. To cancel mute, press this button again. 4 q 7 VOLUME w These buttons are used to adjust the volume level. u: To turn up the volume d: To turn down the volume Press this button to set the SLEEP timer. 6 9 +/– TV VOLUME 7 8 BASIC OPERATION 8 SLEEP 5 These buttons adjust the settings of the SET MENU and TIME/LEVEL mode. 0 TIME/LEVEL TV INPUT 9 Press this button to select the items in the TIME/LEVEL mode. e r 0 ADVANCED OPERATION q Input selector buttons These buttons select the input source. CD: To play a CD TUNER: To listen to an FM or AM broadcast TAPE/MD: To play a tape or MD DVD/LD: To play a DVD or LD SAT/D-TV: To watch a TV or satellite broadcast VCR: To play a video cassette AUX: To use another audio component EXT. DEC.: To play other multi-channel source w EFFECT This flashes in red when pressing a button on the remote control. If it flashes rapidly several times, press the selected button again. Press this button to turn on or off the effect speakers (center and rear). 2 Component selector buttons Press these buttons to select a DSP program. r SET MENU Press this button to select the items in the SET MENU. English Press one of these buttons which corresponds to the component you want to control with the remote control. (The proper code must be set for your component. Refer to “Setup codes” on page 43.) When the component selector button has been pressed, the remote control is set to that component operation mode. e PRG+, PRG– 7 0102V39601-07_EN(UCA) 7 APPENDIX 1 Indicator 1/20/0, 11:28 AM PREPARATION SPEAKER SETUP Speakers to Be Used This unit is designed to provide the best sound-field quality with a 5-speaker system, using main speakers, rear speakers and a center speaker. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacture or speakers with the same tonal quality. The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use highperformance models that can reproduce sounds over the full range for the center speaker and the rear speakers. ■ Use of a subwoofer expands your sound field It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low frequency effect) channel with high fidelity when playing back a source encoded with Dolby Digital. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction. Speaker Placement Refer to the following diagram when you place the speakers. Main speaker (R) Rear speaker (R) Subwoofer Main speaker (L) 1.8 m Center speaker Rear speaker (L) ■ Main speakers Place the right and left main speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the TV monitor should be the same. ■ Rear speakers Place these speakers behind your listening position, facing slightly inwards, nearly 1.8 m (approx. 6 feet) above the floor. ■ Center speaker Align the front face of the center speaker with the front face of your TV monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor and centrally between the main speakers. Note • If the center speaker is not used, the sound will be heard from the right and left main speakers. In that case, “CENTER SP” in the SET MENU is set to the NONE position. (Refer to page 32 for details.) ■ Subwoofer The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce the wall reflections. CAUTION Some types of speakers interfere with a TV monitor. If this problem occurs, move the speakers away from the monitor. If you cannot avoid installing the center speaker or subwoofer near the TV monitor, use magnetically shielded speakers. 8 0103V39608-18_EN(UCA) 8 1/11/0, 5:28 PM CONNECTIONS INTRODUCTION Before Connecting Components CAUTION Never connect this unit and other components to mains power until all connections between components have been completed. Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different terminal names. Refer to the instructions for each component to be connected to this unit. Use RCA-type pin plug cables for connecting audio/video components with the exception described later. The input and output terminals for pin plugs can be distinguished as follows: video signals (composite) V V White analog audio signals for the left channel L L Red analog audio signals for the right channel R R coaxial digital signals C C BASIC OPERATION Yellow After completing all connections, check them again to make sure they are correct. Connecting the Antenna (page 10) Connecting to an External Decoder (page 12) Connecting Speakers (page 14) Connecting the Power Supply Cords (page 16) ADVANCED OPERATION (U.S.A. model) + R – MAIN – + L MAINS A B SET BEFORE POWER ON CENTER R REAR (SURROUND) L + + – – PREPARATION When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products. MAIN A OR B : 4ΩMIN. /SPEAKER A + B : 8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR : 6ΩMIN. /SPEAKER 120 V 60Hz 100W MAX. TOTAL SWITCHED MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER APPENDIX Connecting an Audio Component (page 12) Connecting a Video Component (page 13) IMPEDANCE SELECTOR switch (page 16) English 9 0103V39608-18_EN(UCA) 9 1/11/0, 5:28 PM CONNECTIONS Connecting the Antennas Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Connect each antenna correctly to the designated terminals. ■ Indoor FM antenna (included) Indoor FM antenna Firmly insert the connector into the FM ANT terminal. The indoor FM antenna is only a simple antenna. For reception with better sound quality, installing the outdoor FM antenna (commercially available) is recommended. Note • Do not connect an outdoor FM antenna and the indoor FM antenna at the same time. ■ Outdoor FM antenna Antenna adapter (included for U.S.A. and Canada models) Note Use this adapter to match with F-type connector 75-ohm coaxial cable You may be unable to obtain good FM radio reception depending on your local conditions (distance from the broadcasting station, interposing buildings and mountains, etc.). Consult your dealer or authorized service center and be sure to install an antenna that suits your local conditions. Install the outdoor FM antenna (commercially available) in a high place as far away from any roads as possible to avoid being affected by automobile ignition noise. 75-ohm/300-ohm antenna adapter 300-ohm feeder 10 0103V39608-18_EN(UCA) 10 1/11/0, 5:28 PM CONNECTIONS ■ AM loop antenna (included) AM loop antenna Notes • The AM loop antenna should be placed away from this unit. • The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. INTRODUCTION The AM loop antenna can be removed from the stand and attached to a wall, etc. However, note that the reception sensitivity may deteriorate if the antenna is attached to a metal or steel reinforced wall. ■ Connecting the AM loop antenna 1 2 4 Press the tab and unlock the terminal hole. 3 Return the tab to its original position to lock the lead wires. Lightly pull the lead wires to confirm a good connection. 4 5 Attach the loop antenna to the antenna stand. 5 Antenna stand Insert the AM loop antenna lead wires into the AM ANT and GND terminals. Orient the AM loop antenna so that the best reception is obtained. If you cannot obtain good reception with the AM loop antenna, connect 5 m to 10 m of vinyl covered wire to the AM ANT terminal and extend it outdoors from a window. For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. ADVANCED OPERATION ■ Ground (GND terminal) BASIC OPERATION ■ Outdoor AM antenna Vinyl covered wire (5 m to 10 m) PREPARATION 3 1 2 APPENDIX English 11 0103V39608-18_EN(UCA) 11 1/11/0, 5:28 PM CONNECTIONS Connecting an Audio Component Be sure to connect the right channel (R), left channel (L), input (IN) and output (OUT) properly. (U.S.A. model) L Analog signal R L R L OUTPUT R L LINE OUT R LINE IN Signal flow Tape deck or MD recorder CD player Connecting to an External Decoder External decoder MAIN OUT L R SURROUND OUT L CENTER OUT SUBWOOFER OUT This unit has additional 6-channel audio signal input terminals for connecting an external decoder to this unit. Connect the 6-channel audio signal output terminals of the decoder to the EXTERNAL DECODER INPUT terminals of this unit. R (U.S.A. model) Notes • When a source connected to these terminals is selected, the digital sound field processor cannot be used. • The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and “BASS OUT” in the SET MENU have no effect on a source connected to these terminals. The setting of “MAIN LVL” is effective. (Refer to pages 32 and 33 for details.) 12 0103V39608-18_EN(UCA) 12 1/11/0, 5:28 PM CONNECTIONS Connecting a Video Component DVD/LD player L R VIDEO OUT COAXIAL DIGITAL OUT V C OPTICAL DIGITAL OUT OPTICAL DIGITAL OUT O O VIDEO OUT INTRODUCTION ANALOG AUDIO OUT TV/digital TV, satellite tuner, cable TV ANALOG AUDIO OUT V L R (U.S.A. model) Analog signal V V O L R L R V VIDEO IN V C AUDIO IN VIDEO OUT VIDEO IN Digital signal (optical) Digital signal (coaxial) Signal flow TV monitor VCR ■ Audio signal terminals Be sure to connect the right channel (R), left channel (L), input (IN) and output (OUT) properly. Be sure to connect the input (IN) and output (OUT) properly. ■ Digital audio signal terminals y • The input signal from the DVD/LD input terminals is selected in the following order of priority with the input mode set to AUTO: COAXIAL terminal → OPTICAL terminal → Analog terminal. Refer to page 21 for details. • All digital signal input terminals are applicable to sampling frequencies of 32 kHz, 44.1 kHz and 48 kHz. APPENDIX If your DVD/LD player, TV/digital TV or satellite tuner, etc. has coaxial or optical digital signal output terminals, they can be connected to this unit’s COAXIAL and/or OPTICAL digital signal input terminals. To make a connection between the optical digital signal terminals, remove the cover from each terminal, and then connect them by using a commercially available optical fiber cable that conforms to EIA standards. Other cables might not function correctly. • Be sure to attach the covers when the OPTICAL terminals are not being used in order to protect them from dust. • If your LD player has a Dolby Digital RF signal output terminal, be sure to use the RF demodulator (separately purchased). • No sound will be heard when connecting your LD player’s Dolby Digital RF signal output terminal directly to this unit’s COAXIAL DVD/LD digital signal input terminal. English When making connections between the digital signal terminals, you should connect the components to the samenamed analog audio signal terminals of this unit, because a digital signal cannot be recorded by a tape deck, MD recorder or VCR connected to this unit. 13 0103V39608-18_EN(UCA) 13 ADVANCED OPERATION ■ Video signal terminals Notes BASIC OPERATION AUDIO OUT Video signal PREPARATION L R 1/11/0, 5:28 PM CONNECTIONS Connecting Speakers Main speakers A Main speakers B Right Left Right Left (U.S.A. model) + R – MAIN – + L MAINS A B SET BEFORE POWER ON CENTER Subwoofer connection If you have a subwoofer with builtin amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input terminal of the subwoofer system to the SUBWOOFER OUTPUT terminal of this unit. R REAR (SURROUND) MAIN A OR B : 4ΩMIN. /SPEAKER A + B : 8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR : 6ΩMIN. /SPEAKER L + + – – 120 V 60Hz 100W MAX. TOTAL SWITCHED MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER Right Center speaker Be sure to connect the right channel (R), left channel (L), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. CAUTIONS Left Rear speakers ■ Main speaker terminals One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either of the SPEAKERS A or B terminals. ■ Rear speaker terminals A rear speaker system can be connected to these terminals. • Use speakers with the specified impedance shown on the rear panel of this unit. • Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage the unit and/or speakers. ■ Center speaker terminal A center speaker can be connected to this terminal. 14 0103V39608-18_EN(UCA) 14 1/11/0, 5:28 PM CONNECTIONS ■ Speaker cables Remove approx. 10 mm (3/8”) of insulation from each of the speaker cable. 2 Twist the exposed wires of the cable together to prevent short circuits. ■ Connecting to the MAIN SPEAKERS terminals Red: positive (+) Black: negative (–) 1 2 Unscrew the knob. 3 Tighten the knob to secure the wire. Insert one bare wire into the hole in the side of each terminal. PREPARATION 3 1 2 ■ Connecting to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (–) 1 3 1 2 Open the tab. 3 Return the tab to secure the wire. Insert one bare wire into the hole of each terminal. BASIC OPERATION 2 INTRODUCTION 1 10 mm (3/8”) y Banana plug connections are also possible. Simply insert the banana plug connector into the corresponding terminal. ADVANCED OPERATION APPENDIX English 15 0103V39608-18_EN(UCA) 15 1/11/0, 5:28 PM CONNECTIONS IMPEDANCE SELECTOR Switch WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be damaged. If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide to either position. If so, slide the switch to either position fully when this unit is in the standby mode. Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only when this unit is in the standby mode. (U.S.A. model) IMPEDANCE SELECTOR SET BEFORE POWER ON MAIN A OR B : A+B: CENTER : REAR : MAINS If you use left position right position Center speaker The impedance must be 6 Ω or higher. The impedance must be 8 Ω or higher. Rear speakers The impedance of each speaker must be 6 Ω or higher. The impedance of each speaker must be 8 Ω or higher. If you use one pair of main speakers, the impedance of each speaker must be 4 Ω or higher. If you use one pair of main speakers, the impedance of each speaker must be 8 Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8 Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16 Ω or higher. [Canada model only] The impedance of each speaker must be 8 Ω or higher. 120 V 60Hz 100W MAX. TOTAL SWITCHED 4ΩMIN. /SPEAKER 8ΩMIN. /SPEAKER 6ΩMIN. /SPEAKER 6ΩMIN. /SPEAKER MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER Main speakers Connecting the Power Supply Cords After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if you will not use this unit for a long period of time. ■ AC OUTLETS (SWITCHED) U.S.A. and Canada models .............................. 2 OUTLETS Australia model .................................................. 1 OUTLET Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or POWER). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLET(S) is 100 W. (U.S.A. model) MAINS SET BEFORE POWER ON MAIN A OR B : 4ΩMIN. /SPEAKER A + B : 8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR : 6ΩMIN. /SPEAKER 120 V 60Hz 100W MAX. TOTAL SWITCHED MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER To AC outlet SWITCHED 16 0103V39608-18_EN(UCA) 16 1/11/0, 5:28 PM ADJUSTING THE SPEAKER BALANCE Using the Test Tone The adjustment of each speaker sound output level should be performed at your listening position with the remote control. After completing the adjustments, use VOLUME (u/d) at your listening position to check if the adjustments are satisfactory. PREPARATION 2 3 1 Before You Start Adjusting 1 6 5 2,7 – + – + L R Press AMP(TUNER) on the component selector. 1 Set VOLUME to the “m” position. 2 Press TEST. “TEST LEFT” appears on the display. 2 Turn the power on. 3 Turn up the volume. You will hear a test tone (like pink noise) from each speaker for about two seconds in following order: left main speaker, center speaker, right main speaker, right rear speaker and left rear speaker. The display changes as shown below. Press SPEAKERS A or B to select the main speakers to be used. If you use two main speaker systems, press both A and B. 4 Set BASS, TREBLE and BALANCE to the “0” position. TEST LEFT TEST RIGHT ADVANCED OPERATION 3 BASIC OPERATION 1 4 3 INTRODUCTION This procedure lets you adjust the sound output level balance between the main, center and rear speakers by using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Pro Logic decoder and Dolby Digital decoder. TEST CENTER – + – + L R TEST R SUR. APPENDIX TEST L SUR. Notes 17 0103V39608-18_EN(UCA) 17 1/11/0, 5:29 PM English • If the test tone cannot be heard, turn down the volume, set the unit in the standby mode and check the speaker connections. • If the test tone cannot be heard from the center speaker, check the setting of “CENTER SP” in the SET MENU. ADJUSTING THE SPEAKER BALANCE 4 Adjust BALANCE on the front panel so that the sound output level of the right main speaker and the left main speaker is the same. 5 Press TIME/LEVEL repeatedly to select the speaker to be adjusted. “CENTER”, “R SUR.” or “L SUR.” appears on the display. 6 Press + to raise and – to lower the level. Adjust the sound output levels of the center speaker and the rear speakers so that they become almost the same as that of the main speakers. While adjusting, the test tone is heard from the selected speaker. L R Front panel Note • You cannot adjust the delay time while the test tone is being heard even if “DELAY” appears on the display. 7 When the adjustment is complete, press TEST. “TEST OFF” appears on the display and the test tone stops. Note • If “CENTER SP” in the SET MENU is set to the NONE position, the sound output level of the center speaker cannot be adjusted in step 6. The center channel sound is automatically output from the right and left main speakers. y • Once you have completed the adjustments, you can only adjust the overall volume level of your audio system by using VOLUME (or VOLUME (u/d)). • If there is insufficient sound output from the center and rear speakers, you may decrease the main speaker output level by setting “MAIN LVL” in the SET MENU to “–10 dB”. (Refer to page 33 for details.) 18 0103V39608-18_EN(UCA) 18 1/11/0, 5:29 PM BASIC OPERATION PLAYING A SOURCE 4 2 – – + L 1,6 Select the desired input source with INPUT (or the input selector buttons). (Turn on the TV monitor for video sources.) The name of the selected input source appears on the display. Front panel or Remote control R 6 Input source 6 a. 2 b. 1 Notes Turn the power on. or Front panel 3 Remote control y Front panel For the DVD/LD, TV/digital TV and satellite tuner sources, the current input mode is also shown. Refer to page 21 for details about the input mode. APPENDIX Press SPEAKERS A or B to select the main speakers to be used. If you use two main speaker systems, press both A and B. • An audio source can not be played if the “TAPE/MD MONITOR” indicator lights up or if “EXT. DECODER” appears. Press TAPE/ MD MON / EXT. DECODER twice (or TAPE/MD once) to turn off the “TAPE/MD MONITOR” indicator. Press TAPE/MD MON / EXT. DECODER once (or EXT. DEC.) to turn off “EXT. DECODER”. • If you select and play a video source when the “TAPE/MD MONITOR” indicator lights up or “EXT. DECODER” appears, the play back result will be a video image from the video source and the sound from the audio source selected by using TAPE/MD MON / EXT. DECODER (or TAPE/MD or EXT. DEC.). ADVANCED OPERATION Set VOLUME to the “m” position. Front panel 2 BASIC OPERATION 7 4 To select a tape or an MD source Press TAPE/MD MON / EXT. DECODER (or TAPE/MD) so Front panel that the “TAPE/MD MONITOR” indicator lights up on the display. To select a source connected to the EXTERNAL DECODER INPUT terminals Press TAPE/MD MON / EXT. DECODER repeatedly (or EXT. DEC.) until “EXT. DECODER” appears on the display. PREPARATION 3 7 + 4 INTRODUCTION When using the remote control, press AMP(TUNER) on the component selector. English 19 0104V39619-22_EN(UCA) 19 1/12/0, 9:37 AM PLAYING A SOURCE 5 Play the source. Refer to the instructions for the source component (and page 26 for details about tuning). Note • When controlling an audio/video component (tape deck, MD recorder, CD player, DVD/LD player, etc.) with the remote control, press one of the component selector buttons, (TAPE/MD, CD, DVD/LD, etc.), which corresponds to the component you want to control. Refer to “PRESET REMOTE CONTROL” on page 38. 6 Adjust the volume to the desired output level. If desired, adjust BASS, TREBLE, BALANCE, etc. These controls are only effective for the sound from the main speakers. • BASS controls the low-frequency response. • TREBLE controls the high-frequency response. • BALANCE adjusts the balance of the output volume from the right and left main speakers. or Front panel – Remote control + – + L ■ To mute the sound Press MUTE on the remote control. To cancel mute, press MUTE. Note • During muting, “MUTE ON” appears on the display. ■ When you have finished using this unit Press STANDBY/ON (or POWER) to set this unit in the standby mode. ■ BGV (background video) function The BGV function allows you to combine a video image from a video source with a sound from an audio source. (For example, you can listen to classical music while you are watching a video.) This function can only be controlled with the remote control. Play a video source, and then select an audio source with the input selector buttons on the remote control. The BGV function does not work if you select the audio source with INPUT on the front panel. R Front panel 7 Use the digital sound field processor. Refer to page 22. or Front panel Remote control 20 0104V39619-22_EN(UCA) 20 1/12/0, 9:37 AM PLAYING A SOURCE Input Mode (for the DVD/LD and TV/ digital TV and satellite tuner sources) Press INPUT MODE (or the input selector button that you have pressed to select the input source on the remote control) repeatedly until the desired input mode is shown on the display. or When you turn on the power of this unit, the input mode for the DVD/LD source is always set to AUTO and for TV/ digital TV or satellite tuner source is set according to “SAT INPUT” in the SET MENU. (Refer to page 34 for details.) Front panel Remote control PREPARATION ■ AUTO In this mode, the input signal is selected in the following order of priority: 1. Digital signal encoded with Dolby Digital 2. Normal digital signal (PCM) 3. Analog signal (ANALOG) Note Notes ■ ANALOG In this mode, only an analog signal is selected, even if a digital signal is being input at the same time. Select this mode when you want to use an analog signal instead of a digital signal. ■ Notes on playing an LD source 21 1/12/0, 9:37 AM English 21 APPENDIX • Some audio/video component, such as LD player, output different audio signals through their analog and digital terminals. Change the input mode as necessary. • If the input mode is set to AUTO for the LD source, this unit automatically determines which type of signal the LD source contains. If this unit detects a Dolby Digital signal, the decoder automatically switches to the appropriate setting and reproduces 5.1 channel sound. • If the LD player is transmitting signals by a non-normal method, this unit cannot detect the Dolby Digital signal. In this case, the decoder automatically switches to PCM or analog. • If the LD source does not contain a digital soundtrack, connect the LD player to the analog terminals. • While you are operating the LD player, if you switch from the pause or chapter forwarding function to normal playback, you may hear the PCM or analog sound an instant before the Dolby Digital sound is played. ADVANCED OPERATION • Set the input mode to AUTO to play a DVD/LD source encoded with Dolby Digital. • Set the input mode to ANALOG to play a normal 2-channel source with a Dolby Surround program. • The sound output may be interrupted for some LD and DVD players in the following situation: The input mode is set to AUTO. A search is performed while playing the disc encoded with Dolby Digital, and then disc playing is restored. The sound output is interrupted for a moment because the digital signal was selected again. • The input mode cannot be changed for the CD, TUNER, TAPE/ MD, VCR and AUX sources because only analog signals are used for these. • The current input mode appears on the display when the DVD/ LD, TV/digital TV or satellite tuner source is selected or the input mode is changed. BASIC OPERATION • If digital signals are input from both the OPTICAL and COAXIAL terminals, the digital signal from the COAXIAL terminal is selected. 0104V39619-22_EN(UCA) INTRODUCTION This unit allows you to switch the input mode for sources that send both digital and analog signals to this unit. The AUTO and ANALOG input modes are provided. ■ Switching the input mode DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT 3 Selecting a DSP Program You can enhance your listening experience by selecting a DSP program. Refer to pages 23 to 25 for details about each program. – + – + L Press PRG+ or PRG– repeatedly to select the desired program. The name of the selected program appears for a moment and the selected DSP program indicator lights up on the display. R DSP program indicator 2 y If desired, adjust the delay time and the sound output level of each speaker. (Refer to pages 35 and 36 for details.) 2 Notes 3 ■ On the front panel 1 Make sure that the effect speakers (center, rear, and subwoofer) are turned on. 2 Press PROGRAM h or l repeatedly to select the desired program. The name of the selected program appears for a moment and the selected DSP program indicator lights up on the display. • You can select a DSP program for each of the input sources. Once you select a program, it is linked with the input source selected at that time. So, when you select the input source next time, the same program is automatically selected. • When a monaural source is being played with PRO LOGIC/ Normal or PRO LOGIC/ENHANCED, no sound will be heard from the main speakers and the rear speakers. Sound can only be heard from the center speaker. However, if “CENTER SP” in the SET MENU is set to the NONE position, the center channel sound is output from the main speakers. • When a source connected to the EXTERNAL DECODER INPUT terminals of this unit is selected, the digital sound field processor cannot be used. Canceling the Sound Effect (turning off the effect speakers) Press EFFECT to cancel the sound effect and monitor only the main sound. Press EFFECT again to turn the sound effect back on. Front panel or Remote control DSP program indicator ■ On the remote control 1 Make sure that the effect speakers (center, rear, and subwoofer) are turned on. 2 Press AMP(TUNER) on the component selector. Notes • If the sound effect is canceled when Dolby Digital is decoding, the sounds of all channels are mixed and output from the main speakers. • If you turn off the sound effect when Dolby Digital is decoding, it may happen that the sound is output faintly or not output normally, depending on the source. In that case, turn back on the sound effect. 22 0104V39619-22_EN(UCA) 22 1/12/0, 9:37 AM SOUND FIELD PROGRAM When you select a CINEMA DSP program, one of the built-in decoders (Dobly Pro Logic and Dolby Digital) is turned on according to which type of signals the source being played contains. INTRODUCTION This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theaterlike experience in your listening room. You can create outstanding audio sound by selecting a suitable DSP program (this will, of course, depend on what you are listening to). The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital re-creations of actual acoustic environments. No. PROGRAM 1 q SURROUND SUBPROGRAM [1] PRO LOGIC/Normal ( o ) • Input source: [3] PRO LOGIC/ENHANCED (ox) • Input source: This program ideally simulates the multisurround speaker systems of the 35 mm-film movie theater. Dolby Pro Logic decoding or Dolby Digital decoding and digital sound field processing are precisely performed without altering the original sound orientation. The surround effect produced by the sound field folds around the viewer naturally from the rear to the right and left and toward the screen. ADVANCED OPERATION Dolby Surround 2-ch Dolby Digital • Output channel: 4 channels • DSP: 1 (surround) [4] DOLBY DIGITAL/ENHANCED (gx) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 2 (surround L, R) The built-in Dolby Pro Logic decoder or Dolby Digital decoder precisely reproduces the sound and effect of a source encoded with Dolby Surround or Dolby Digital. The realization of a highly efficient decoding process improves cross talk and channel separation, and makes sound positioning smoother and more precise. In this program, the digital sound field processor is not turned on. BASIC OPERATION Dolby Surround 2-ch Dolby Digital • Output channel: 4 channels • DSP: — [2] DOLBY DIGITAL/Normal ( g ) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: — FEATURES PREPARATION ■ For movie or audio/video sources (Program No. 1 to No. 5: CINEMA DSP programs) APPENDIX English 23 0105V39623-25_EN(UCA) 23 1/12/0, 9:37 AM SOUND FIELD PROGRAM No. 2 PROGRAM MOVIE THEATER 1 SUBPROGRAM [1] 70 mm SPECTACLE (ox) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [2] DGTL SPECTACLE (gx) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [3] 70 mm SCI-FI ( o x ) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [4] DGTL SCI-FI ( g x ) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) 3 MOVIE THEATER 2 [1] 70 mm ADVENTURE (ox) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [2] DGTL ADVENTURE (gx) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [3] 70 mm GENERAL ( o x ) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [4] DGTL GENERAL ( g x ) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) FEATURES This program creates the extremely wide sound field of a movie theater. It precisely reproduces the source sound in detail, giving both the video and the sound field incredible reality. It is ideal for any kind of video source encoded with Dolby Surround or Dolby Digital (especially large-scale movie productions). Clearly reproduces dialog and sound effects in the latest sound form of science fiction films, thus creating a broad and expansive cinematic space amid the silence. You can enjoy science fiction films in a virtual-space sound field that includes Dolby Surround and Dolby Digitalencoded software employing the most advanced techniques. Ideal for precisely reproducing the sound of the newest multi-track films. The sound field is made to be similar to that of the newest movie theaters, so the reverberations of the sound field itself are restrained as much as possible. The data for the sound field of an opera house are used for the front presence, so the threedimensional feeling of the sound field is emphasized, and dialog is precisely oriented on the screen. By using the data for the sound field of a concert hall on the surround sound field, powerful reverberations are generated. You can enjoy watching action, adventure movies, etc. with strong presence. This program is for reproducing sounds on a multi-track film, and is characterized by a soft and extensive sound field. The front presence of the sound field is relatively narrow. It spatially spreads all around and toward the screen, restraining echo effect of conversations without losing clarity. For the surround sound field, the harmony of music or chorus sounds beautifully in a wide space at the rear of the sound field. 24 0105V39623-25_EN(UCA) 24 1/12/0, 9:37 AM SOUND FIELD PROGRAM No. 4 PROGRAM MONO MOVIE This program is designed specifically to enhance monaural sources. Compared to a strictly mono setting, the sound image is wider and slightly forward of the speaker pair, lending an immediacy to the overall sound. It is particularly effective for old mono movie, news broadcasts and dialog. Monaural 1 channel 1 TV SPORTS • Input source: • Output channel: • DSP: This program is furnished with a tight sound field in which the sound will not spread excessively at the front, but the rear surround produces dynamic sound expansion. It is the most suitable for sports programs. Audio/Video 2 to 5.1 channels 2 to 3 (presence & surround) INTRODUCTION • Input source: • Output channel: • DSP: 5 FEATURES ■ For Hi-Fi audio sources No. DISCO • Input source: • Output channel: • DSP: 7 This program simulates the acoustic environment of a disco in the heart of a lively city. The sound is dense and highly concentrated. 2-ch PCM/Analog audio 2 channels 1 ROCK CONCERT • Input source: • Output channel: • DSP: This program is ideally suited for rock music. You will experience a dynamic and lively sound field. 2-ch PCM/Analog audio 2 channels 1 CONCERT HALL • Input source: • Output channel: • DSP: This program creates the expansive ambience of a large concert hall. It is suited for orchestra and opera music. 2-ch PCM/Analog audio 2 channels 1 CINEMA DSP: Dolby Surround + DSP/Dolby Digital + DSP Digital sound fields are created in both the presence and rear surround zones of the Dolby Pro Logic-decoded sound field. They create a wide acoustic environment and emphasize the surround effect in the room, letting you feel as much presence as if you were watching a movie in a popular Dolby Stereo theater. ADVANCED OPERATION ■ Dolby Pro Logic + 2 digital sound fields BASIC OPERATION 8 FEATURES PREPARATION 6 PROGRAM ■ Dolby Digital + 3 digital sound fields 0105V39623-25_EN(UCA) 25 1/12/0, 9:37 AM English 25 APPENDIX Digital sound fields are created in the presence zone and independently on the left and right surround zones of the Dolby Digital-decoded sound field. They create a wide acoustic environment and strong surround effect in the room without losing high channel separation. With the wide dynamic range of Dolby Digital sound, this sound field combination lets you feel as if you were watching a movie in the newest Dolby Digital theater. This is the most ideal home theater sound at the present time. TUNING Automatic tuning is effective when station signals are strong and there is no interference. However, if the signal from the station you want to select is weak, you must tune in to it manually (manual tuning). 5 1 Press PRESET/TUNING h once to tune in to a higher frequency and l once to tune in to a lower frequency. Press the button again if the tuning search does not stop at the desired station. Note – + – + L • If you tune in manually to an FM station, it will be automatically received in monaural mode to increase the signal quality. R y 5 42 3 Automatic Tuning 1 2 • Use the manual tuning method if the tuning search does not stop at the desired station (because the signal from the station is weak). • When tuned in to a station, the frequency of the received station is shown on the display. Manual Tuning Use INPUT to select the tuner as the input source. Press FM/AM to select the reception band (FM or AM). “FM” or “AM” appears on the display. 1 Use INPUT to select the tuner as the input source. 2 Press FM/AM to select the reception band (FM or AM). “FM” or “AM” appears on the display. or or 3 Press TUNING MODE so that the “AUTO” indicator lights up on the display. 3 Press TUNING MODE so that the “AUTO” indicator goes off. Lights up 4 Press PRESET/TUNING (EDIT) to turn “ z ” off. Goes off 4 Press PRESET/TUNING (EDIT) to turn “ z ” off. Turn “ z ” off Turn “ z ” off 5 Press PRESET/TUNING h or l to tune in to the desired station. To continue the tuning search, hold down the button. 26 0106V39626-29_EN(UCA) 26 1/12/0, 9:38 AM TUNING Automatic Preset Tuning (for FM stations only) + – + L ■ When automatic preset tuning is completed R 13 2 1 Press FM/AM to select the FM band. The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure in the section “To Recall a Preset Station” on page 28. PREPARATION – You can select the preset number from which the unit will store FM stations and/or begin tuning toward lower frequencies. Before automatic preset tuning begins (after pressing MEMORY in step 3), 1. Press A/B/C/D/E and PRESET/TUNING to select the preset number with which the first station will be stored. The automatic preset tuning will stop when stations have all been stored up to E8. 2. Press PRESET/TUNING (EDIT) to turn “ z ” off and then press PRESET/TUNING l to begin tuning toward lower frequencies. INTRODUCTION You can make use of the automatic preset tuning function for FM stations only. This function enables the unit to automatically tune in with strong signals and to sequentially store up to 40 FM stations (5 groups x 8 stations). ■ Automatic preset tuning options Notes Press TUNING MODE so that the “AUTO” indicator lights up on the display. Lights up 3 ADVANCED OPERATION Hold down MEMORY for about three seconds. The preset number, the “MEMORY” and “AUTO” indicators flash. After about five seconds, automatic preset tuning begins from the frequency currently displayed toward the higher frequencies. Received stations are sequentially stored as A1, A2 ... A8. If more than 8 stations have been tuned, they are stored as preset station numbers in other groups (B, C, D and E) in that order. BASIC OPERATION 2 • A new setting can be stored in place of the former one. • You can manually replace a preset station with another FM or AM station by simply using the manual preset tuning method. • Even if the number of received stations is not enough to be stored up to E8, automatic preset tuning is automatically ended after searching for all stations. • Only FM stations with sufficient signal strength are stored by automatic preset tuning. If the station you want to store is weak in signal strength, tune in to it manually in monaural mode and store it by using the manual preset tuning method. Flashes APPENDIX Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the memory will be erased. If so, store the stations again by using preset tuning methods. English 27 0106V39626-29_EN(UCA) 27 1/20/0, 11:29 AM TUNING Manual Preset Tuning To Recall a Preset Station You can also store up to 40 stations (5 groups x 8 stations) manually. You can recall any desired station simply by selecting the preset station number with which it was stored. You can also recall a preset station with the remote control. Press AMP(TUNER) on the component selector and press TUNER on the input selector. – + – + L R 3 4 2,5 – 1 Tune in to the desired station. Refer to page 26 for the tuning procedure. 2 Press MEMORY. The “MEMORY” indicator flashes for about five seconds. + – + L R 1 2 Flashes 3 4 5 6 Press A/B/C/D/E repeatedly to select the desired group (A to E) of preset stations before the “MEMORY” indicator goes off. Make sure that “ z ” appears on the display. The selected group appears on the display. Press PRESET/TUNING h or l to select a preset station number (1 to 8) with which you want to store the station before the “MEMORY” indicator goes off. Press h to select a higher preset station number and l to select a lower preset station number. Press MEMORY before the “MEMORY” indicator goes off. The displayed station has been stored as the preset group and number you have selected, and the reception band and frequency appear on the display. 1 2 1 Press A/B/C/D/E to select the required group of preset stations. Make sure that “ z ” appears on the display. or Front panel 2 Remote control Press PRESET/TUNING h or l (or PRESET +/–) to select a preset station number (1 to 8). The preset group and number appear on the display along with the reception band, frequency and signal strength information. or Front panel Repeat steps 1 to 5 to store other stations. Notes • A new setting can be stored in place of the former one. • The reception mode (stereo or monaural) is stored along with the station frequency. 28 0106V39626-29_EN(UCA) 28 1/12/0, 9:39 AM Remote control TUNING Exchanging Preset Stations You can exchange the assignment of two preset stations with each other. INTRODUCTION ■ Example: If you want to exchange preset station “E1” with “A5”. 2,4 + – + L PREPARATION – R Recall preset station “E1”. Refer to the procedure in the section “To Recall a Preset Station” on page 28. 2 Hold down (PRESET/TUNING) EDIT for about three second. “E1” and the “MEMORY” indicator flash. BASIC OPERATION 1 Flashes 3 ADVANCED OPERATION Recall preset station “A5” by using the buttons on the front panel. “A5” and the “MEMORY” indicator flash. Flashes 4 Press (PRESET/TUNING) EDIT again. The display shows the exchange of stations has been completed. APPENDIX English 29 0106V39626-29_EN(UCA) 29 1/20/0, 11:29 AM RECORDING A SOURCE ON TAPE, MD OR VIDEO CASSETTE Recording adjustments and other operations are performed from the tape deck, MD recorder or VCR. Refer to the instructions for these components. 2 1,4 y If a tape deck or MD recorder is being used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MON / EXT. DECODER (or TAPE/MD). Notes – + – + L R 4 • The DSP program and the setting of VOLUME, BASS, TREBLE and BALANCE have no effect on the material being recorded. • A source connected to this unit only through the digital terminals cannot be recorded by the tape deck, MD recorder or VCR connected to this unit. • A source connected to the EXTERNAL DECODER INPUT terminals of this unit cannot be recorded. • Check the copyright laws in your country to record from records, CDs, radio, etc. Recording of copyrighted material may infringe copyright laws. If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals. 2 1 Set VOLUME to the “m” position. Front panel 2 Select the source you want to record. or Front panel Remote control 3 Begin recording by the tape deck, MD recorder or VCR connected to this unit. 4 Play the source and then turn up the volume to confirm the input source. or Front panel Remote control 30 0107V39630_EN(UCA) 30 1/12/0, 9:42 AM ADVANCED OPERATION SET MENU Press SET MENU repeatedly to select the item you want to adjust. The selected item appears on the display. 3 Press + or – repeatedly to adjust the setting. 4 Repeat steps 2 and 3 to adjust the setting of any other item in the same way. PREPARATION 1. CENTER SP 2. REAR SP 3. MAIN SP 4. BASS OUT 5. MAIN LVL 6. D.D. LFE 7. D-RANGE 8. CNTR DELAY 9. MEM. GUARD 10.SAT INPUT 2 INTRODUCTION This unit provides you with the following items in the SET MENU to maximize the performance of your system and expand your enjoyment for audio listening and video watching. Adjustments should be performed with the remote control while watching the information on the display. 1 2 1 Press AMP(TUNER) on the component selector. ADVANCED OPERATION 3 Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the settings of the SET MENU will automatically return to the preset positions and values. If so, adjust the settings of the SET MENU again. BASIC OPERATION Adjusting Items in the SET MENU APPENDIX English 31 0108V39631-37_EN(UCA) 31 1/12/0, 9:42 AM SET MENU Description of Each Item 1. CENTER SP 3. MAIN SP Choices: LARGE/SMALL Preset position: LARGE Choices: LRG (Large)/SML (Small)/NONE Preset position: LRG (Large) LRG (Large) Select this position if your center speaker is approximately the same size as the main speakers. In this position, fullrange signals on the center channel are directed to the center speaker. SML (Small) Select this position if you use a center speaker that is smaller than the main speakers. In this position, low bass signals (below 90 Hz) on the center channel are distributed to the SUBWOOFER OUTPUT terminal (or to the right and left main speakers if “BASS OUT” is set to the MAIN position). NONE Select this position if you do not have a center speaker (4-speaker system). In this position, full-range signals on the center channel are directed to the right and left main speakers. LARGE Select this position if your main speakers have high ability for bass reproduction. In this position, full-range signals on the main channels are directed to the right and left main speakers. SMALL Select this position if your main speakers do not have high ability for bass reproduction. However, if your system does not include a subwoofer, do not select this position. In this position, low bass signals (below 90 Hz) on the main channels are distributed to the SUBWOOFER OUTPUT terminal if “BASS OUT” is set to the SW or BOTH position. 4. BASS OUT Choices: SW/MAIN/BOTH Preset position: BOTH SW Select this position if your system includes a subwoofer. In this position, signals on the LFE channel and other low bass signals that are distributed from other channels are directed to the SUBWOOFER OUTPUT terminal when playing a source encoded with Dobly Digital. 2. REAR SP Choices: LARGE/SMALL Preset position: LARGE Note LARGE Select this position if your rear speakers have high ability for bass reproduction, or if a subwoofer is connected in parallel to the rear speaker. In this position, full-range signals on the rear channels are directed to the rear speakers. SMALL Select this position if your rear speakers do not have high ability for bass reproduction. In this position, low bass signals (below 90 Hz) on the rear channels are distributed to the SUBWOOFER OUTPUT terminal (or to the right and left main speakers if “BASS OUT” is set to the MAIN position). • When playing a 2-channel source (tape, MD, CD, video cassette etc.), select the BOTH position to direct low bass signals (below 90 Hz) to the SUBWOOFER OUTPUT terminals. MAIN Select this position if your system does not include a subwoofer. In this position, besides full-range signals on the main channels, signals on the LFE channel and other low bass signals (below 90 Hz) that are distributed from other channels are directed to the right and left main speakers. BOTH Select this position if your system includes a subwoofer. In this position, signals on the LFE channel are directed to the SUBWOOFER OUTPUT terminal. Low bass signals on the main channels are directed to both the main speakers and the SUBWOOFER OUTPUT terminal. 32 0108V39631-37_EN(UCA) 32 1/12/0, 9:42 AM SET MENU 5. MAIN LVL Choices: NORM (Normal)/–10 dB Preset position: NORM (Normal) Choices: MAX/STD (Standard)/MIN Preset position: MAX INTRODUCTION NORM (Normal) Normally select this position. 7. D-RANGE (Adjusting the dynamic range) Note –10 dB Select this position if the sound output from the main speakers is too loud and cannot be balanced with the sound output from the center and rear speakers. In this position, the sound output from the main speakers is attenuated. Control range: –20 dB to 0 dB (in 1 dB steps) Preset value: 0 dB This adjusts the output level of the LFE channel. If the LFE signals are mixed with signals of other channels and they are directed to the same speakers, the ratio of the LFE signal level to the level of the other signals can be adjusted. STD (Standard) In this position, a source encoded with Dolby Digital is reproduced in the “compressed” dynamic range of the source that is suitable for low-level listening. Note • It may happen that sound is output faintly or not output normally depending on the source. In that case, select the MAX or STD position. APPENDIX MIN In this position, the dynamic range is more reduced than in the STD position. Selecting this position will be effective when you must listen to a source at a low level. ADVANCED OPERATION Note • This adjustment is only effective when Dolby Digital is being decoded and the selected source encoded with Dolby Digital contains LFE signals. MAX In this position, a source encoded with Dolby Digital is reproduced in the original sound track’s wide dynamic range to provide you with powerful sounds just like those in a movie theater. Selecting this position will be even better if you can listen to a source at a high output level in a room specially soundproofed for audio/video enjoyment. BASIC OPERATION 6. D.D. LFE (Adjusting the output level of the LFE channel for Dolby Digital) “Dynamic range” is the difference between the maximum level and the minimum level of sounds. Sounds on a movie originally designed for movie theaters feature a very wide dynamic range. Dolby Digital technology can modify the original sound track into a home audio format with this wide dynamic range unchanged. Powerful sounds of extremely wide dynamic range are not always suitable for home use. Depending on the condition of your listening environment, it may not be possible to increase the sound output to a level as high as that in a movie theater. However, at the normal level suitable for listening in your room, the low-level parts of source sound often cannot be heard well because they will be lost among noise in your environment. Dolby Digital technology has also made it possible to reduce an original sound track’s dynamic range for a home audio format by “compressing” the sound data. PREPARATION Notes • The setting of “CENTER SP”, “REAR SP”, “MAIN SP” and “BASS OUT” have no effect on a source connected to the EXTERNAL DECODER INPUT terminals on the rear of this unit. • Once you have adjusted appropriately for “CENTER SP”, “REAR SP”, “MAIN SP”, “BASS OUT” and “MAIN LVL”, you do not have to change any settings unless your speaker system is modified. • This adjustment is only effective when Dolby Digital is being decoded. English 33 0108V39631-37_EN(UCA) 33 1/12/0, 9:42 AM SET MENU 8. CNTR DELAY (Adjusting the delay of the center sound) 9. MEM. GUARD (Locking the settings) Control range: 0 ms to 5 ms (in 1 ms steps) Preset value: 0 ms Choices: ON/OFF Preset position: OFF Note • This adjustment is only effective when Dolby Digital is being decoded and the selected source encoded with Dolby Digital contains center channel signals. This adjusts the delay between the main sound (on the main channels) and dialog, etc. (on the center channel). The larger the value, the later the dialog, etc. is generated. This makes sounds from the left main, center and right main speakers reach your listening position at the same time. This is achieved by delaying the sound from the center speaker if the distance from the center speaker to your listening position is shorter than the distance from the right and left main speaker to your listening position. If you wish to prevent accidental alterations to the settings of the SET MENU and other adjustments on this unit, select the ON position. The following settings on this unit can be locked: • Settings of other items in the SET MENU • Settings in the TIME/LEVEL mode • Settings when using TEST 10.SAT INPUT (Selecting the initial input mode for a source connected to the SAT/D-TV input terminals) Choices: AUTO/LAST Preset position: AUTO The input mode for a source connected to the SAT/D-TV input terminals of this unit can be automatically set when the power of this unit is turned on. Refer to page 21 for details about the input mode. AUTO In this position, the input mode is always set to AUTO. LAST In this position, the input mode is automatically set to that selected the last time when the power of this unit was turned on. 34 0108V39631-37_EN(UCA) 34 1/13/0, 5:36 PM DELAY TIME AND SPEAKER OUTPUT LEVELS Delay Time Notes Notes • The sound output level of the center speaker cannot be adjusted when the input signal is analog, PCM audio, or encoded with Dolby Digital in 2-channel. • If “CENTER SP” in the SET MENU is set to the NONE position, the sound output level of the center speaker cannot be adjusted. This is because the center channel sound is automatically output from the right and left main speakers. • Once the sound output level has been adjusted, the level will be the same for all DSP programs. Speaker Center Right rear Left rear Subwoofer Control range (dB) –20 to +10 –20 to +10 –20 to +10 –20 to 0 Preset value 0 0 0 0 BASIC OPERATION ADVANCED OPERATION • Adding too much delay will cause an unnatural effect with some sources. • The sound is momentarily interrupted while adjusting the delay time. Preset Control Program value range (ms) 1. PRO LOGIC/Normal 15 to 30 20 DOLBY DIGITAL/Normal 0 to 15 5 PRO LOGIC/ENHANCED 15 to 30 20 DOLBY DIGITAL/ENHANCED 0 to 15 5 2. 70 mm SPECTACLE 15 to 30 23 DGTL SPECTACLE 1 to 99 15 70 mm SCI-FI 15 to 30 20 DGTL SCI-FI 1 to 99 16 3. 70 mm ADVENTURE 15 to 30 20 DGTL ADVENTURE 1 to 99 15 70 mm GENERAL 15 to 30 20 DGTL GENERAL 1 to 99 15 4. MONO MOVIE 1 to 99 49 5. TV SPORTS 1 to 99 9 6. DISCO 1 to 99 40 7. ROCK CONCERT 1 to 99 16 8. CONCERT HALL 1 to 99 44 If desired, you can adjust the sound output level of each speaker even if it has already been adjusted in “ADJUSTING THE SPEAKER BALANCE” on pages 17 and 18. PREPARATION You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the sound effect from the rear speakers. The larger the value, the later the sound effect is generated. The delay time can be individually adjusted to all DSP programs. Sound Output Level of the Center, Right Rear and Left Rear Speakers, and Subwoofer INTRODUCTION When using the digital sound field processor with the Dolby Pro Logic decoder or Dolby Digital decoder, you can adjust the delay time between the main sound and sound effect, and each speaker’s output level as you wish. APPENDIX English 35 0108V39631-37_EN(UCA) 35 1/20/0, 11:29 AM DELAY TIME AND SPEAKER OUTPUT LEVELS Adjusting Method 3 Press + or – to adjust the delay time or speaker output levels. 4 Repeat steps 2 and 3 to adjust the settings of any other item. Adjustments should be performed with the remote control while watching the information on the display. 1 3 2 1 Press AMP(TUNER) on the component selector. 2 Press TIME/LEVEL repeatedly to select the item you want to adjust. Each time you press TIME/LEVEL, the selected item changes and appears on the display as below. Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the latest values for the delay time and the center/rear/ subwoofer output levels that were set will automatically return to the preset values. If so, adjust the delay time and output levels again. DELAY CENTER R SUR. L SUR. SWFR Note • Depending on the setting of the SET MENU, you may not be able to select all these items. 36 0108V39631-37_EN(UCA) 36 1/12/0, 9:42 AM SLEEP TIMER Notes • First press AMP(TUNER), TAPE/MD, CD or DVD/LD on the component selector to set the SLEEP timer for this unit. • The SLEEP timer is effective for the components connected to the AC OUTLET(S) on the rear panel of this unit. Note Play a source you want to enjoy when you are going to sleep. 2 Press SLEEP repeatedly to select the desired SLEEP time. Each time you press SLEEP, the SLEEP time will change as below: 90 60 • The SLEEP timer can also be canceled by setting the unit in the standby mode by using POWER on the remote control (or STANDBY/ON), or by disconnecting the AC power cord from the AC power outlet. BASIC OPERATION 1 120 Press SLEEP repeatedly until “SLEEP OFF” appears on the display. It will soon disappear and the “SLEEP” indicator will go off. 30 The SLEEP timer is off (SLEEP OFF). (This is the state before SLEEP is pressed.) ADVANCED OPERATION Flashes 3 PREPARATION Setting the SLEEP Timer Canceling the Selected SLEEP Timer INTRODUCTION The SLEEP timer can be used to automatically set this unit in the standby mode. This timer is useful when you are going to sleep while enjoying a broadcast or other desired input source. The SLEEP timer can only be set with the remote control. The “SLEEP” indicator soon lights up on the display after the SLEEP timer has been set. The display returns to the previous indication. Lights up APPENDIX English 37 0108V39631-37_EN(UCA) 37 1/12/0, 9:42 AM PRESET REMOTE CONTROL The provided remote control is factory set to control not only this unit but also most YAMAHA audio components connected to it. There are eight component selector buttons. Press one of these buttons which corresponds to the component you want to control with the remote control. For example, if you press CD on the component selector, the remote control is set to the CD operation mode, allowing the CD player to be controlled by the buttons on the remote control. AMP(TUNER) You can perform the basic operations of this unit. Refer to page 7. CD The code for a YAMAHA CD player is factory set. DVD/LD & DVD MENU An LD player can be controlled in the DVD/LD mode. A DVD player can be controlled in the DVD/LD and DVD MENU modes. The code for a YAMAHA DVD player is factory set. If the remote control does not operate your YAMAHA DVD player, you need to set the code number “0048”. TAPE/MD The code for a YAMAHA tape deck is factory set. (The code for the YAMAHA MD recorder can also be set.) VCR A VCR can be controlled. TV A TV can be controlled. CBL/SAT A cable TV or satellite tuner can be controlled. Note • The button functions on the remote constrol differ depending on the operation mode. Refer to the following pages for details. Controlling the Components Connected to This Unit ■ Example: To control YAMAHA CD player 5 2 3 4 7 6 1 Make sure that VOLUME is set to the “m” position. 2 Press AMP(TUNER) on the component selector. 3 Turn on the power. 4 Press CD on the input selector. 5 Press CD on the component selector. 6 Press p. Refer to page 40 for the CD player operation buttons. 7 Adjust the volume. If you set the remote control with the manufacturers’ codes listed from page i at the end of this manual, you can control other brands of components. Refer to “Setup codes” on page 43 for details. 38 0109V39638-44_EN(UCA) 38 1/12/0, 9:42 AM PRESET REMOTE CONTROL Description of Each Mode ■ TAPE/MD MODE INTRODUCTION Note • TV VOLUME functions if you have set the code for your TV. Press TAPE/MD. PREPARATION POWER (TAPE) This button turns this unit on if you have set the code for a YAMAHA tape deck. This button turns on the tape deck that has a remote control with a power button if you have set the code for another manufacturer. (MD) This button turns this unit on if you have set the code for the YAMAHA MD recorder. Input selector buttons BASIC OPERATION EFFECT VOLUME MUTE DISPLAY (MD) APPENDIX DECK A/B (TAPE) This button selects deck A or B on a double-cassette tape deck. e PAUSE (MD) This button gives a pause in operation. a DIR B (TAPE) This button selects the playing direction of deck B. SKIP+ (MD) This button skips to the next track. s STOP This button stops operation on a tape deck or MD recorder. f FAST FORWARD (TAPE) This button winds a tape fast forward. SEARCH (MD) This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen. ADVANCED OPERATION SLEEP r REC/PAUSE This button gives a pause in recording on a tape deck or MD recorder. p PLAY This button plays a tape or an MD. b DIR A (TAPE) This button selects the playing direction of deck A. SKIP– (MD) This button skips to the previous track. w REWIND (TAPE) This button rewinds a tape. SEARCH (MD) This button initiates a backward search on the track that is playing to find the point from which you want to listen. TV VOLUME English The dark-shaded buttons do not function. Refer to the instructions for details of each component. 39 0109V39638-44_EN(UCA) 39 1/12/0, 9:42 AM PRESET REMOTE CONTROL ■ CD MODE Note • TV VOLUME and TV INPUT function if you have set the code for your TV. Press CD. POWER This button turns this unit on if you have set the code for a YAMAHA CD player. This button turns on the CD player that has a remote control with a power button if you have set the code for another manufacturer. Input selector buttons EFFECT DISC SKIP +/– (for a CD player with CD changer) These buttons skip to the next or previous CD. VOLUME MUTE SLEEP TV VOLUME DISPLAY TV INPUT p PLAY This button plays a CD. b SKIP– This button skips to the beginning of the previous track. w SEARCH This button initiates a backward search on the track that is playing to find the point from which you want to listen. e PAUSE This button gives a pause in operation. The button functions as PAUSE/STOP* for operating a YAMAHA CD player under factory setting. a SKIP+ This button skips to the beginning of the next track. s STOP This button stops operation. The button functions as PAUSE/STOP* for operating YAMAHA CD players. f SEARCH This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen. y PAUSE/STOP function Press the button once to give a pause in operation and press once more to stop operation. The dark-shaded buttons do not function. Refer to the instructions for details of each component. 40 0109V39638-44_EN(UCA) 40 1/12/0, 9:43 AM PRESET REMOTE CONTROL ■ DVD/LD MODE Note • TV VOLUME and TV INPUT function if you have set the code for your TV. INTRODUCTION Press DVD/LD. Input selector buttons EFFECT DISC SKIP +/– PREPARATION POWER (DVD) This button turns this unit on if you have set the code for a YAMAHA DVD player. This button turns on the DVD player that has a remote control with a power button if you have set the code for another manufacturer. (LD) This button turns this unit on if you have set the code for a YAMAHA LD player. This button turns on the LD player that has a remote control with a power button if you have set the code for another manufacturer. VOLUME MUTE SLEEP PAUSE SKIP – STOP TV VOLUME DISPLAY TV INPUT SKIP + PLAY SEARCH SEARCH BASIC OPERATION ■ DVD MENU MODE Note • TV VOLUME and TV INPUT function if you have set the code for your TV. POWER This button turns the unit on if you have set the code for a YAMAHA DVD player. This button turns on the DVD player that has a remote control with a power button if you have set the code for another manufacturer. ADVANCED OPERATION Press DVD MENU. Numeric buttons CLEAR +10 DISC SKIP +/– VOLUME MUTE RETURN MENU DOWN INDEX APPENDIX MENU UP MENU LEFT TV VOLUME TV INPUT MENU RIGHT MENU SELECT MENU TITLE English The dark-shaded buttons do not function. Refer to the instructions for details of each component. 41 0109V39638-44_EN(UCA) 41 1/12/0, 9:43 AM PRESET REMOTE CONTROL ■ VCR MODE ■ CBL/SAT MODE Note Note • TV VOLUME, TV INPUT and TV SLEEP function if you have set the code for your TV. Press VCR. VCR POWER • TV VOLUME, TV INPUT and TV SLEEP function if you have set the code for your TV. CBL/SAT POWER Press CBL/SAT. CHANNEL CHANNEL EFFECT CHANNEL ENTER VCR CHANNEL +/– VOLUME MUTE TV SLEEP VCR REC Press this button twice to start recording. CBL/SAT CHANNEL +/– VOLUME TV VOLUME MUTE DISPLAY TV INPUT VCR PAUSE TV SLEEP MENU UP MENU LEFT VCR PLAY VCR FAST FORWARD VCR STOP VCR REWIND MENU DOWN RECALL ■ TV MODE Note • You can control your VCR if you have set the code for it. TV POWER Press TV. CHANNEL TV CHANNEL +/– VOLUME TV MUTE TV SLEEP VCR REC Press this button twice. VCR STOP VCR REWIND EFFECT CHANNEL ENTER TV VOLUME DISPLAY TV INPUT VCR PAUSE VCR PLAY VCR FAST FORWARD The dark-shaded buttons do not function. Refer to the instructions for details of each component. 42 0109V39638-44_EN(UCA) 42 1/12/0, 9:43 AM +100 CHANNEL ENTER TV VOLUME DISPLAY TV INPUT MENU RIGHT MENU SELECT MENU PRESET REMOTE CONTROL Advanced Information ■ Setup codes 1 2 Turn on the VCR to be used. 3 Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. 4 Use the numeric buttons to enter the four-digit code for the second (and third) VCR. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. 5 Press POWER (or any other button) on the remote control to check if you have set the code correctly. If the VCR cannot be controlled with the remote control, try setting another code for the same manufacturer. Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. Use the numeric buttons to enter the four-digit manufacturer’s code for the component to be used. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. Press POWER (or any other button) on the remote control to check if you have set the code correctly. If your component cannot be controlled with the remote control, try setting another code for the same manufacturer. Press CBL/SAT or DVD MENU on the component selector. ADVANCED OPERATION 5 1 2 BASIC OPERATION 4 Press one of the component selector buttons which corresponds to the component to be controlled. Note • If you want to control a second (and third) VCR in the DVD MENU mode, you must set the code for an LD player in the DVD/LD mode. PREPARATION 3 Turn on your component to be used. You can control a second (and third) VCR in the CBL/SAT and DVD MENU modes if a cable TV or satellite tuner, or DVD player is not being used. INTRODUCTION You can set the code for the manufacturer of your component after pressing the component selector buttons other than AMP(TUNER). ■ To use a second (and third) VCR Notes APPENDIX • You can set only one code for one mode. • In the DVD/LD and DVD MENU modes: – Be sure to press DVD/LD on the component selector before entering the code for the DVD/LD player. The code set in the DVD/LD mode is also simultaneously set in the DVD MENU mode. You cannot set the code for a DVD player after pressing DVD MENU on the component selector. – DVD MENU operations cannot be performed for some DVD players. • A second (and third) VCR can be controlled. Refer to “To use a second (and third) VCR” for details. • If your component does not respond to any of the codes listed for the manufacturer, use the original remote control supplied with your component. English 43 0109V39638-44_EN(UCA) 43 1/12/0, 9:43 AM PRESET REMOTE CONTROL ■ Returning to the factory-set codes To return all components to the factory-set codes, follow these steps. 1 Press one of the component selector buttons other than AMP(TUNER). 2 Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. 3 Enter the code number “9990”. Make sure that the indicator flashes twice. To return each component to the factory-set codes, follow these steps. 1 Press one of the component selector buttons which corresponds to the component to be returned to the factory-set code. 2 Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. 3 Enter the code number “0000”. Make sure that the indicator flashes twice. The following codes are factory set. Component selector button TV CBL/SAT VCR DVD/LD CD TAPE/MD Component Code TV Satellite tuner VCR DVD player CD player Tape deck 0101 0006 0002 0008 (YAMAHA DVD player) 0005 (YAMAHA CD player) 0004 (YAMAHA Tape deck) We recommend that you write all the code numbers you have set on the “Quick Reference Card”. 44 0109V39638-44_EN(UCA) 44 1/12/0, 9:43 AM APPENDIX TROUBLESHOOTING ■ General SYMPTOM CAUSE REMEDY Refer to page The power cord is not connected or the plug is not completely inserted. Firmly connect the power cord. 16 The IMPEDANCE SELECTOR switch on the rear panel is not fully set to the right or left position. Set the switch fully to the right or left position when the unit is in the standby mode. 16 The unit does not work normally. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or by a power supply with low voltage. Set the unit in the standby mode and disconnect the AC power cord from the AC power outlet. After about 30 seconds have passed, connect the power and operate the unit again. — No sound and/or no picture. Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables may be defective. An appropriate input source has not been selected. Select an appropriate input source with INPUT or TAPE/MD MON / EXT. DECODER (or the input selector buttons). 19 The speaker connections are not secure. Secure the connections. 14 SPEAKERS have not been set properly. Set SPEAKERS corresponding to the speakers in use to the ON position. 19 The sound is muted. Set VOLUME to the “m” position, press MUTE to cancel a mute and adjust the volume. 20 Digital signals other than PCM audio and the signals encoded with Dolby Digital which this unit cannot reproduce are being input to this unit by a CD-ROM, etc. The protection circuit has been activated because of a short circuit, etc. Play a source whose signals this unit can reproduce. — Set the unit in the standby mode and then turn on to reset the protection circuit. — The SLEEP timer has functioned. Turn on the power, and play the source again. 37 Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 14 Adjust it to the appropriate position. 20 The sound effect is off. Press EFFECT to turn it on. 22 A Dolby Surround or Dolby Digital decoding DSP program is being used with material not encoded with Dolby Surround or Dolby Digital. Select another DSP program. 25 No sound from the center speaker. The sound output level of the center speaker is set to minimum. Raise the level of the center speaker. 35 “CENTER SP” in the SET MENU is set to the NONE position. Select the LRG or SML position. 32 Incorrect DSP program is selected. Select the appropriate program. No sound from the rear speakers. The output level of the rear speakers is set to minimum. 23, 24, 25 — The source encoded with Dolby Digital does not have a center channel signal. Raise the output level of the rear speakers. 25 English A monaural source is being played with the PRO Select another DSP program suitable for the LOGIC/Normal or PRO LOGIC/ENHANCED monaural source. program. 35 45 0110V39645-50_EN(UCA) 45 1/12/0, 9:43 AM APPENDIX Incorrect setting of BALANCE. No sound from the effect speakers. ADVANCED OPERATION Only the speaker on one side can be heard. BASIC OPERATION The sound suddenly goes off. 12, 13 PREPARATION The unit fails to turn on when STANDBY/ON is pressed, or enters in the standby mode soon after the power has been turned on. INTRODUCTION If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center. TROUBLESHOOTING SYMPTOM No sound from the subwoofer. CAUSE “BASS OUT” in the SET MENU is set to the SW or MAIN position when playing a 2-channel source. REMEDY Select the BOTH position. Refer to page 32 — The source does not contain low bass signals (below 90 Hz). A “humming” sound can be heard. Incorrect cable connections. Firmly connect the audio plugs. If the problem persists, the cables may be defective. The volume level cannot be increased, or the sound is distorted. The component connected to the TAPE/MD OUT (REC) terminals of this unit is in the standby mode. Turn on the power to the component. The sound effect cannot be recorded. It is not possible to record the sound effect by a tape deck or MD recorder connected to the TAPE/MD OUT (REC) terminals of this unit. The DVD/LD, TV/digital TV or satellite tuner source cannot be recorded by tape deck, MD recorder or VCR connected to this unit. The DVD/LD player, TV/digital TV or satellite tuner is connected to the unit only through the digital terminals. Make additional connections between the analog terminals. 13 Adjusting this unit by using SET MENU, TIME/ LEVEL or TEST cannot be performed. “MEM. GUARD” in the SET MENU is set to the ON position. Set “MEM. GUARD” to the OFF position. 34 12, 13 — 30 ■ Tuner SYMPTOM FM stereo reception is noisy. There is distortion, and clear reception cannot be obtained even with a good FM FM antenna. CAUSE The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. There is multipath interference. REMEDY Check the antenna connections. Try using a high-quality directional FM antenna. Use the manual tuning method. Adjust the antenna position to eliminate multipath interference. The desired station cannot be tuned in with the automatic tuning method. The station is too weak. Use the manual tuning method. Use a high-quality directional FM antenna. Previously preset stations can no longer be tuned in. The unit has been disconnected for a long period. Re-store the stations. The desired station cannot be tuned in with the automatic tuning method. The signal is weak or the antenna connections are loose. Tighten the AM loop antenna connections and orient it for best reception. Use the manual tuning method. Noises result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat, but it is difficult to eliminate all noise. Move this unit away from the TV. There are continuous AM crackling and hissing noises. There are buzzing and whining noises (especially in the evening). A TV set is being used nearby. 46 0110V39645-50_EN(UCA) 46 1/12/0, 9:43 AM Refer to page 10, 26 10 10, 26 27 11, 26 11 — TROUBLESHOOTING ■ Remote control SYMPTOM The remote control does not work. REMEDY Refer to page Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition the unit. The batteries are weak. Replace all batteries with new ones. 2 The component to be controlled has not been selected. Press one of the component selector buttons which corresponds to the component to be controlled. 38 The manufacturer’s code has not been set properly. Enter the code again. 43 3 INTRODUCTION The unit or other component cannot be controlled. CAUSE Try setting another code for the same manufacturer. ■ Others CAUSE REMEDY Refer to page The sound is degraded when listening with headphones to a tape deck or CD player connected to this unit. This unit is in the standby mode. Turn on the power of the unit. — There is noise interference from digital or high-frequency equipment, or the unit. The unit is too close to the digital or highfrequency equipment. Move the unit further away from such equipment. — PREPARATION SYMPTOM BASIC OPERATION ADVANCED OPERATION APPENDIX English 47 0110V39645-50_EN(UCA) 47 1/12/0, 9:43 AM SPECIFICATIONS AUDIO SECTION FM SECTION • Minimum RMS Output Power 20 Hz to 20 kHz, 0.06% THD, 8 ohms Main L/R, Center, Rear L/R ..................................................... 60 W 1 kHz, 0.09% THD, 8 ohms Main L/R, Center, Rear L/R ....................................... 70 W*/65 W • Tuning Range .................................... 87.5/87.50 to 107.9/108.00 MHz • Maximum Output Power (EIAJ) 1 kHz, 10% THD, 8 ohms .......................................................... 95 W • DIN Standard Output Power 1 kHz, 0.7% THD, 4 ohms ......................................................... 90 W • IEC Output Power 1 kHz, 0.06% THD, 8 ohms ....................................................... 65 W • Dynamic Power (IHF) 8/6/4/2 ohms ...................... 90/110/130/150 W*, 85/105/125/145 W • Damping Factor 20 Hz to 20 kHz, 8 ohms ................................................................ 60 • Frequency Response CD etc. to MAIN L/R ................................ 20 Hz to 20 kHz, ±0.5 dB • Total Harmonic Distortion (20 Hz to 20 kHz) CD etc. to MAIN L/R, 1/2 power, 8 ohms ............................ 0.025% • Signal-to-Noise Ratio (IHF-A Network) CD etc. to MAIN L/R (150 mV, Input Shorted) ......................................................... 96 dB (250 mV, Input Shorted) ....................................................... 100 dB • Residual Noise (IHF-A Network) MAIN L/R .............................................................................. 150 µV • Input Sensitivity/Impedance CD etc. ................................................................. 150 mV/47 k-ohms EXT. DECODER ......................................... 150 mV/40 – 47 k-ohms • Output Level/Impedance REC OUT ........................................................... 150 mV/1.2 k-ohms SUBWOOFER ....................................................... 4.0 V/1.2 k-ohms PHONES ................................................................. 0.47 V/390 ohms • Usable Sensitivity (DIN) Mono (S/N 26 dB) ................................................................... 0.9 µV Stereo (S/N 46 dB) ................................................................... 28 µV • Selectivity (two signals, 40 kHz Dev., ±300 kHz) ...................... 55 dB • Signal-to-Noise Ratio (Mono/Stereo) DIN ................................................................................. 75 dB/69 dB IHF ................................................................................. 81 dB/75 dB • Harmonic Distortion (1 kHz) Mono/Stereo ........................................................................ 0.1/0.2% • Stereo Separation (1 kHz) ........................................................... 48 dB • Frequency Response ........................................ 20 Hz to 15 kHz, ±1 dB • Antenna Input ...................................................... 75 ohms, Unbalanced AM SECTION • Tuning Range ............................................ 530/531 to 1,710/1,611 kHz • Usable Sensitivity ................................................................. 300 µV/m • Signal-to-Noise Ratio ................................................................... 52 dB • Antenna ........................................................................... Loop antenna GENERAL • Power Supply [U.S.A. and Canada models] .................................. AC 120 V, 60 Hz [Europe, U.K. and Singapore models] .................... AC 230 V, 50 Hz [Australia model] ..................................................... AC 240 V, 50 Hz [China model] ......................................................... AC 220 V, 50 Hz [General model] ............................. AC 110/120/220/240 V, 50/60 Hz • Power Consumption ...................................................... approx. 190 W • AC Outlets (100 W max. total) [U.K. and Australia models] ..................................... 1 (SWITCHED) [Other models] .......................................................... 2 (SWITCHED) • Channel Separation (Vol. –30 dB) CD etc. (Input 5.1 k-ohms Terminated, 1 kHz/10 kHz) ..................................................................................... 60 dB/45 dB • Dimensions (W x H x D) ..................... 435 x 151 x 391 mm (17-1/8’’ x 5-15/16’’ x 15-3/8’’) • Tone Control Characteristics BASS: Boost/cut .......................................................... ±10 dB/50 Hz TREBLE: Boost/cut ................................................... ±10 dB/20 kHz VIDEO SECTION • Accessories ................................................................ AM loop antenna .......................................................................... Indoor FM antenna ..................... 75-ohm/300-ohm antenna adapter (U.K. model only) ........................ Antenna adapter (U.S.A. and Canada models only) ................................................................................. Remote control ........................................................................................... Batteries • Video Signal Type ........................................................... NTSC or PAL Specifications are subject to change without notice. * for U.S.A. and Canada models • Weight ............................................................................ 10 kg (22 lbs.) • Video Signal Level ...................................................... 1 Vp-p/75 ohms • Signal-to-Noise Ratio .................................................................. 50 dB • Monitor Out Frequency Response .................... 5 Hz to 10 MHz, –3 dB 48 0110V39645-50_EN(UCA) 48 9/28/0, 3:12 PM GLOSSARY The Dolby Surround and Dolby Digital sound systems show their full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater that uses a multitude of speakers. Trying to create a sound environment similar to that of a movie theater in your home is difficult because of the room size, material inside the walls, the number of speakers, and so on. In other words, your listening room is very different from a movie theater. However, YAMAHA DSP technology allows you to create nearly the same sound experience as that of a large movie theater in your home by compensating for the lack of presence and dynamics in the listening room with original digital sound fields combined with Dolby Surround or Dolby Digital. The YAMAHA “CINEMA DSP” logo indicates those programs that are created by the combination of YAMAHA DSP technology and Dolby Surround or Dolby Digital. ■ Dolby Digital ■ LFE 0.1 Channel This channel is for reproduction of low bass signals. The frequency range for this channel is 20 Hz to 120 Hz. This channel is called the channel 0.1 because it only reproduces a low frequency range compared to the full-range from 20 Hz to 20 kHz that is reproduced by the 5 channels in a Dolby Digital 5.1 channel system. BASIC OPERATION Dolby Digital is a digital surround sound system that provides completely independent multi-channel audio to you. Dolby Digital provides five full-range channels in what is sometimes referred to as a “3/2” configuration: three front channels (left, center and right), and two surround channels. A sixth bass-only effect channel is also provided for output of LFE (low frequency effect), or low bass effects that are independent of other channels. (This is called the “LFE channel”.) This channel is counted as 0.1, thus giving rise to the term 5.1 channels in total. The wide dynamic range of sound reproduced by the five full-range channels and precise sound orientation by digital sound processing provides listeners with excitement and realism that have never been experienced before. PREPARATION ■ CINEMA DSP CINEMA DSP Dolby Surround uses four discrete channels and five speakers to reproduce realistic and dynamic sound effects: two main channels (left and right), a center channel for dialog, and a rear channel for special sound effects. The rear channel reproduces sound within a narrow frequency range. Most video tapes and laser discs include Dolby Surround encoding, as do many TV and cable broadcasts. The Dolby Pro Logic decoder built into this unit employs a digital signal processing system that stabilizes each channel for even more accurate sound positioning than is available with standard analog processors. INTRODUCTION ■ Dolby Surround ADVANCED OPERATION APPENDIX English 49 0110V39645-50_EN(UCA) 49 1/12/0, 9:43 AM INDEX A M Accessories .......................................................................... 2 AC outlet ........................................................................... 16 Antennas ...................................................................... 10, 11 Muting ............................................................................... 20 B BALANCE ........................................................................ 20 BGV (background video) function .................................... 20 C Canceling sound effect ...................................................... 22 CINEMA DSP ............................................................. 25, 49 Connections Antennas ................................................................ 10, 11 Audio components (tape deck/MD recorder and CD player) ......................................................................... 12 Digital connections ...................................................... 13 Speakers ...................................................................... 14 TV monitor .................................................................. 13 Video components (DVD/LD player, VCR and TV/ digital TV, satellite tuner) ............................................ 13 P Playing ............................................................................... 19 Preset stations To recall a preset station .............................................. 28 Exchanging preset stations .......................................... 29 Preset tuning Automatic preset tuning .............................................. 27 Manual preset tuning ................................................... 28 R Recording .......................................................................... 30 Remote control Basic operations ............................................................ 7 Batteries ......................................................................... 2 Component selector ................................................. 7, 38 Factory-set code .......................................................... 44 Manufacturer’s codes .......... i (at the end of this manual) Setup codes .................................................................. 43 D S Delay time (TIME/LEVEL mode) .................................... 35 Display ................................................................................. 6 Dolby Digital ..................................................................... 49 Dolby Surround ................................................................. 49 DSP program ............................................................ 22 to 25 External decoder ................................................................ 12 SET MENU ....................................................................... 31 Sleep timer ......................................................................... 37 Speaker Output levels (TIME/LEVEL mode) .......................... 35 Output mode (SET MENU) .................................. 32, 33 Speaker balance (test tone) .......................................... 17 Placement ...................................................................... 8 STANDBY/ON .................................................................... 4 F T E Front panel ........................................................................... 4 I IMPEDANCE SELECTOR switch ................................... 16 Input mode ......................................................................... 21 L Test tone ....................................................................... 17, 18 Tone controls ..................................................................... 20 Tuning Automatic tuning ......................................................... 26 Manual tuning ............................................................. 26 LFE .............................................................................. 33, 49 50 0110V39645-50_EN(UCA) 50 1/12/0, 9:43 AM LIST OF MANUFACTURER’S CODES LISTES DES CODES FABRICANT Elin Elta Emerson 1001 0331 0001, 0021, 0061, 0071, 0081, 0091, 0111, 0811, 0821, 0831, 0841, 0851, 0861, 0871, 0901, 0921, 0941, 0981, 1011, 1031, 1051, 1081, 1091 Envision 0361, 1111 Erres 1001 Etron 0331 Ferguson 1001 Finlux 1001 Fisher 0171, 0801, 0981 Formenti 0441 Formonti 1001 Fortress 1141 Fujitsu 1091 Funai 1051, 1091, 1341, 1361, 1411, 1451, 1501, 1521 Futuretech 1051 GE 0131, 0161, 0201, 0751, 0761, 0771, 0781, 0791, 0811, 0861, 1041 GEC 0271, 1001 Gemini 0391 Genexxa 0431 Gibralter 0891, 1031, 1111 GoldStar 0031, 0121, 0351, 0411, 0731, 0741, 0861, 0941, 0971, 1001, 1031, 1111, 1151 Goodmans/Tashiko 0271, 0661, 1001 Granada 1001 Grundig 1781, 1791, 1801, 1811, 1821, 1831, 1841, 1851, 1861, 1871, 1881 Gunpy 1051, 1091 H/K 0721 Hallmark 0861 Hanseatic 1001 Harvard 1051, 1061 Hinari 1001, 1091 Hitachi 0181, 0351, 0671, 0681, 0691, 0701, 0711, 0871, 0941, 0971, 1351 Hypson 1001 Ima 1051 Indiana 1001 Infinity Reference 0101 Interfunk 1001 ITT 0611 Janeil 1131 JBL 0101 JCB 0951 Jensen 0311 Jinxing 1531, 1541, 1551, 1561, 1571, 1621, 1631, 1641, 1651, 1691, 1731 JVC 0261, 0281, 0641, 0651, 0661, 0841 Kawasho 0901 TV A-Mark A Tandy Abex Admira Adventura Aiko Akai Alba Alleron Ambassador Amstrad Anam 1161 0941 1151 1141 1131 1121 0331, 1101, 1111 0431 1091 1081 0481, 1081 0251, 1041, 1051, 1061, 1071 Anam National 1041 AOC 0361, 1021, 1031, 1111, 1161 Archer 1161 Audiosonic 1001 Audiovox 1051, 1161 Awai 1481 Bauer 0441 Baur 1001 Beijing 1511, 1551, 1561 Belcor 1031 Bell & Howell 0981, 0991 Beon 1001 Bradford 1051 Brockwood 1031 Broksonic 1161 Bush 1001 Candle 0351, 0361, 0961, 0971, 1111, 1131 Capehart 1021 Carver 0101 Cathay 1001 Celebrity 0951 Centurion 0411 Changhong 1541, 1551, 1561, 1621 Citizen 0351, 0361, 0921, 0931, 0941, 0961, 0971, 1111, 1121, 1131 Clairtone 1011 Clarivox 1001 Concerto 0351, 0971 Conrowa 1751 Contec 0901, 0911, 1011, 1051 Corando 0941 Craig 0251, 1051 Crown 0941, 1051 Curtis Mathes 0161, 0361, 0931, 0941, 0981, 1111 CXC 1051 Daewoo 0291, 0301, 0331, 0721, 0941, 1001, 1031, 1121, 1191, 1531, 1581, 1591, 1601 Dansai 1001 Daytron 0941, 1031 Decca 0271, 1001 Dixi 0331, 1001, 1071 Dumont 0891, 1031 Dynatech 0881 Electroband 0951, 1011 Electrohome 0941 Electron 0941 Kaypani Kenwood Kloss KTV 1021 0361, 1031, 1111 0631, 0721, 1131 0921, 0941, 1011, 1051, 1111 Leyco 1001 Liesenk & Tter 1001 Lloytron 0941 Loewe 1001 Logik 0991, 1771 Luxman 0351, 0971 Lxi 0101, 0621, 0761, 0861, 0981 Magnavox 0101, 0341, 0391, 0401, 0411, 0421, 0581, 0591, 0601, 0611, 0631, 0661, 0961, 1111 Majestic 0991 Marantz 0101, 0221, 0361, 1001, 1111 Mark 1001 Matsui 0271, 0331, 1001 Mediator 1001 Megatron 0691, 0861, 1161 MEI 1011 M Electronic 1001 Memorex 0331, 0571, 0861, 0971, 0981, 0991, 1771 Metz 1791, 1831, 1891, 1901, 1911, 1921, 1931, 1941 MGA 0361, 0561, 0571, 0861, 1031, 1111 Midland 0751, 0761, 0891, 0941, 1151 Mitsubishi 0221, 0321, 0561, 0571, 0661, 0861, 1031, 1101, 1381 Montgomery 1091 Motorola 1041, 1141 MTC 0351, 0361, 0881, 0931, 0971, 1011, 1031, 1111 Multitech 0881, 1051 NAD 0551, 0621, 0861 NEC 0241, 0351, 0361, 0661, 0971, 1031, 1111, 1321, 1711 Neckermann 1001 Nei 1001 Nikkai 0271, 0431, 1001, 1151 Nikko 0861, 1111, 1121 Novabeam 0721 NTC 1121 Onwa 1051 Optimus 0551 Optonica 0541, 1141 Orion 0831, 1001 Osaki 0271, 1151 Otto Versand 1001 Panasonic 0101, 0191, 0251, 0751, 1041, 1311, 1371, 1431 Panda 1541, 1721 Penny Peony Philco Philips Phonola Pilot Pioneer Portland Priceclub Prism Proscan Protech Proton Pulsar Pulser Quasar Quelle Radio Shack Radiola RCA Realistic Rhapsody R-line Runco Saisho Sampo Samsung Samsux Sanyo SBR Schneider Scimitsu Scotch Scott Sears Shanghai Sharp Shogun Signature 0161, 0361, 0521, 0531, 0621, 0731, 0751, 0761, 0781, 0791, 0861, 0931, 0941, 1031, 1041, 1111, 1151, 1161 1561, 1621 0361, 0581, 0591, 0601, 0611, 0631, 0961, 1031, 1111 0101, 0401, 1001 1001 0941, 1031, 1111 0511, 0551, 0871, 1331 0941, 1031, 1121 0931 0751 0761 1001 0501, 0861, 0941, 1021, 1161 0891 1031 0251, 0751, 1041 1001 0541, 0941, 1031, 1051, 1151 1001 0051, 0141, 0151, 0181, 0411, 0491, 0531, 0761, 0771, 0871, 1031 0541, 0861, 0941, 0971, 0981, 1031, 1051, 1111, 1151 1011 1001 0891, 1111 0331, 1081 0361, 0941, 1021, 1111, 1151 0331, 0341, 0351, 0361, 0861, 0931, 0941, 0971, 1001, 1031, 1111, 1151, 1461 0941 0171, 0231, 0271, 0661, 0801, 0911, 0981, 1231, 1251, 1261 1001 1001 1031 0861 0831, 0861, 0941, 1031, 1051, 1091 0101, 0161, 0171, 0351, 0481, 0521, 0621, 0761, 0801, 0861, 0971, 0981, 1091 1561, 1681 0461, 0471, 0541, 0661, 0911, 0941, 1141, 1241, 1271 1031 0991, 1771 i 03V396code(UCA) 1 1/13/0, 11:52 AM Simpson Solavox Sonoko Sontec Sony 0581, 0961 1151 1001 1001 0371, 0451, 0661, 0841, 0951, 1281, 1441 Soundesign 0861, 0961, 1051, 1091 Soundwave 1001 Spectricon 1161 Squareview 0481 SSS 1031, 1051 Star-lite 1051 Suprem 0951 Supre-macy 1131 Surpa 0351, 0971 Sylvania 0101, 0361, 0441, 0581, 0591, 0601, 0611, 0631, 0961, 1111 Symphonic 0481 Sysline 1001 Tandy 0271, 0431, 1141 Tatung 0271, 0881, 1001, 1041, 1161 Tcl 1561, 1631, 1701 Technics 0751 Techwood 0351, 0751, 0971 Teknika 0101, 0351, 0571, 0931, 0941, 0961, 0971, 0991, 1031, 1051, 1091, 1121, 1131, 1771 Teletech 0331 Tera 0501 Thakral 1671 Thorm 1001 TMK 0351, 0861, 0971, 1081 Toshiba 0381, 0521, 0621, 0661, 0931, 0981, 1301 Tosonic 1011 Totevision 0941 Trical 0911 Universal 0781, 0791 Universum 1001 Vector Research 0361, 1111 Vestel 1001 Victor 0651, 1201, 1211, 1221 Video Concept 1101 Vidikron 0101, 0211 Vidtech 0861, 1031 Viking 1131 Wards 0101, 0361, 0451, 0541, 0581, 0591, 0601, 0611, 0771, 0781, 0791, 0861, 0971, 0991, 1031, 1091, 1111, 1771 Watson 1001 Xogego 1611, 1621, 1661, 1741, 1761 Yamaha 0221, 0361, 0571, 1031, 1111, 1141, 1381 Yoko 1001 Zenith 0011, 0041, 0891, 0991, 1771 Zonda 1161 CABLE ABC 0256, 0376 Antronix 0136 Archer 0136, 0286 BBT 0076 Cabletime 0166 Cablevision 0196 Colour Voice 0306, 0346 Comtronics 0216, 0276 Eagle Comronics 0276 Eastern 0066 Electricord 0206 Electus 0266 GE 0116, 0126 GEC Cable System 0196 Hamlin H5 0676 Hamlin H6 0666 Hamlin H6S 0656 Hamlin H8 0646 Hamlin H9 0636 Jerrold 0256 Jerrold 400L 0626 Jerrold 450L 0616 Jerrold 550 0606 Jerrold Osd Catv 0596 Jerrold Sprucer 0436 Magnavox/Philips 0416, 0426 Mamm 0296 Memorex 0386 Movie Time 0146, 0206 Northcoast 0016 NSC 0146 Oak 0106 Oak Sigma 450 0546 Oak Sigma 550 0536 Panasonic TZ 120/130 0476 Panasonic TZ 170/180 0446 Panasonic TZ140 0466 Panasonic TZ150/160 0456 Paragon 0386 Philips 0036, 0216, 0306, 0316, 0326, 0336, 0346 Pioneer 0006, 0086 Pioneer BR50 0846 Pioneer BR60/70/80/81/82 0696 Pioneer BR90 0556 Pulsar 0386 RCA Digital Satellite System 0396, 0406 Realistic 0136 Regency/Eastern 0686 Runco 0386 Samsung 0276 Scientific Atlanta 175/475 0576 Scientific Atlanta 75 0366, 0586 Scientific Atlanta 8650 0566 Signal 0276 SL Marx 0276 Spectavision 0236 Standard Components 0186 Starcom V 0256 Stargate 0276 Sylvania/Texscan 0376, 0496 Teknika 0176 Teleservice 0056 Teleview 0276 Texscan 0186, 0376 TFC 0026 Tocom 0226, 0356 Tocom 5503A 0526 Tocom 5503VIP/5507 0516 Tocom TC56 0506 Toshiba 0386 Tudi 0046 Unika Universal Videoway Viewstar Zenith 0136 0136, 0156, 0206, 0286 0096 0216 0246, 0386, 0486 SATELLITE TUNER Alpha Star 0826 Chaparral 0756 Echostar 0836 General Instrument 0776 HTS 0836 Hughes Network Systems 0816 Jerrold 0776, 0786 Panasonic 0806 Primestar 0776, 0786 RCA 0766 Sony 0796 VCR A Tandy Adventura Aiko Aiwa Akai 0902 0992 0982 0992 0262, 0942, 0952, 0962, 0972 American High 0932 Amstrad 0992 ASA 0002, 0912 Asha 0922 Audio Dynamics 0202 Audiovox 0912 Beaumark 0922 Bell & Howell 0902 Blaupunkt 0412 Broksonic 0872, 0882, 0892 Bush 0852 Calix 0912 Canon 0862, 0932 CCE 0852, 0982 Citizen 0912, 0982 Colt 0852 Craig 0832, 0842, 0852, 0912, 0922 Curtis Mathes 0662, 0822, 0932 Cybernex 0922 Daewoo 0802, 0812, 0982 DBX 0202 Dynatech 0472, 0992 Electrohome 0912 Electrophonic 0912 Emerex 0792 Emerson 0072, 0132, 0142, 0152, 0162, 0172, 0182, 0192, 0212, 0702, 0712, 0722, 0732, 0742, 0752, 0762, 0772, 0782, 0872, 0882, 0892, 0912, 0952, 0992, 1072 Finlux 0002, 0992 Fisher 0682, 0692, 0842, 0902 Fuji 0672, 0932 Funai 0992 Garrard 0992 GE 0662, 0822, 0932 Go Video 0642, 0652 GoldStar 0082, 0632, 0912 Goodmans 0402 Gradiente 0992 Granda 0612, 0902 Grundig 0002 H/K 1082 ii 03V396code(UCA) 2 1/13/0, 11:52 AM Harley Davidson 0992 Harmon/Kardon 0632, 1082 Harwood 0752, 0852 Headquarter 0612 HI-Q 0842 Hinari 0852 Hitachi 0102, 0562, 0572, 0582, 0592, 0602, 0992 ITT 0942 JVC 0202, 0522, 0532, 0542, 0552 Kenwood 0202, 0542, 0612, 0632, 0902 KLH 0852 Kodak 0912, 0932 Lloyd 0992 Logik 0852 Luxor 0942 LXI 0022, 0912 Magnavox 0002, 0482, 0492, 0502, 0512, 0932 Magnin 0922 Marantz 0002, 0202, 0402, 0632, 0932 Marta 0912 Matsui 0722 Matsushita 0932 MEI 0222, 0932 Memorex 0232, 0242, 0472, 0512, 0612, 0842, 0902, 0912, 0922, 0932, 0992 MGA 0762, 0952 MGA Technology 0922 Minolta 0592, 0602 Mitsubishi 0452, 0462, 0542, 0762, 0952, 1082 Motorola 0472, 0932 MTC 0922, 0992 Multitech 0852, 0992 NAD 0442 NEC 0122, 0202, 0292, 0422, 0432, 0542, 0632 Nikko 0912 Noblex 0922 Olympus 0412, 0932 Optimus 0442, 0472, 0912 Optonica 0402 Orion 0212, 0722, 0742, 0772 Osaki 0912 Panasonic 0012, 0052, 0092, 0222, 0372, 0382, 0392, 0412, 0932 Penny 0202, 0432, 0602, 0632, 0692, 0912, 0922, 0932 Pentax 0592, 0602 Perdio 0992 Philco 0002, 0932 Philips 0002, 0282, 0402, 0492, 0932 Pilot 0912 Pioneer 0442, 0542 Proscan 1002, 1012, 1022, 1032, 1042, 1052, 1062 Pulsar 0512 Quarter 0612 Quartz 0272, 0612 Quasar 0382, 0392, 0932 Radio Shack 0912, 0992 Radix 0912 Randex 0912 RCA 0112, 0382, 0392, 0482, 0592, 0602, 0662, 0822, 0942 Realistic 0402, 0472, 0612, 0682, 0842, 0902, 0912, 0922, 0932, 0992 Ricoh 0352, 0362 Saisho 0212, 0582, 0722, 0732, 0742, 0772 Salora 0612, 0762 Samsung 0212, 0312, 0922, 0962 Sanky 0472, 0512 Sansui 0292, 0542, 0832 Sanyo 0242, 0612, 0842, 0902, 0922 SBR 0002, 0282 Schneider 0852 Scott 0342, 0712, 0762, 0872, 0882, 0892 Sears 0302, 0592, 0602, 0612, 0682, 0692, 0842, 0902, 0912, 0932 Sharp 0402, 0472 Shintom 0852 Shogun 0922 Singer 0852 Sony 0032, 0332, 0352, 0362, 0672, 0792, 0932 STS 0602 Sunpak 0352 Sylvania 0002, 0492, 0502, 0762, 0932, 0992 Symphonic 0992 Tandy 0992 Tashiko 0712, 0992 Teac 0992 Technics 0932 Teknika 0322, 0912, 0932, 0992 Telefunken 0252 TMK 0212, 0732, 0772, 0922 Toshiba 0062, 0302, 0342, 0622, 0682, 0712, 0762 Totevision 0912, 0922 Unitech 0922 Vector Research 0202, 0432, 0632 Victor 0532, 0542, 0552 Video Concepts 0202, 0432, 0632, 0952 Wards 0322, 0402, 0472, 0482, 0602, 0712, 0842, 0852, 0922, 0932, 0992 Yamaha 0202, 0632, 0762 Zenith 0042, 0362, 0512, 0672 LD PLAYER Aiwa Denon Disco Vision Funai Hitachi (E) Kenwood Magnavox Marantz Mitsubishi NAD Panasonic Philips Pioneer RCA Realistic Sharp Sony Victor Yamaha CD PLAYER Acoustic Research 1295 ADC 0025, 0065 Adcom 0205, 0255, 1015 ADS 0265 Aiwa 0295, 0945, 1035, 1055 Akai 0175, 0485, 0535 Alpine 1215, 1305 Audio-Technica 0545 BSR 0245, 0655, 0775 California Audio Lab 0055 Capetronic 1205 Carrera 0245 Carver 0285, 1135 Casio 0345 Crown 0185 Curtis Maths 0345 Denon 0275, 0875, 0885 Deual (E) 0505 Dynamic Bass (H) 0555 Emerson 0205, 0325, 1105 Eroica 1275 Fisher 0095, 0555, 0925, 1005 Garrard 0365 Genexxa 0305, 0325, 1105 GoldStar 1225, 1265, 1135, 1335 H/K 0105, 0175, 0465, 0995 Hitachi 0195, 0505, 0205, 0815 Inkel 0115, 0395 JVC 0315 Kenwood 0045, 0095, 0405, 0585, 0725, 0735, 0745, 0755, 0895 Kyocera 0025 Luxman 0075, 0425, 0675, 0705, 0715, 0985 Magnavox 0165, 0215, 0645, 0955 Marantz 0215, 0235, 0375, 0785, 1345 McIntosh 0355, 1085 MCS 0905, 1315 Memorex 0205, 0225, 0235, 0305, 0325, 1105 DVD PLAYER Akai JVC Onkyo Panasonic Philips Pioneer Samsung Sharp Sony Toshiba Yamaha 0157 0147 0017 0157 0017 0087, 0107 0027 0027 0137 0137 0077, 0177 0027 0037, 0017, 0137 0167 0157 0127 0047, 0057, 0117 0097 0007, 0067 0108 0168 0128 0048 0188 0208, 0228 0148 0068 0028 0088 0008, 0048 MGA Mission Mitsubishi MTC NAD 0135 0215 0135, 0445 1255 0035, 0615, 0685, 0695 Nakamichi 0125, 0435, 0515 NEC 0255, 0905, 0965 Nikko 0545, 1005 Onkyo 0155, 0455, 0495, 0805, 1155 Optimus 0225, 0245, 0555, 0595, 0845, 0855, 0865, 0895, 0935 Panasonic 0055, 0825, 1095, 1125 Penny 0905 Philips 0165, 0215 Pioneer 0305, 0935, 1045 Proton 0215, 1185 Quasar 0055 RCA 0205, 0915, 1115 Realistic 0205, 0225, 0235, 0325, 0555, 0845 Revox 1175 Rotel 0215 Saba Telecommander (E) 0505 SAE 0215 Samsung 1285 Sansui 0215, 0625, 0975, 1025, 1105 Sanyo 0145, 0555, 0635, 0765 Scott 0325, 1105 Sears 0345 Sharp 0235, 0665, 0895, 1065, 1075 Sherwood 0115, 0235, 0395, 0475 Siements Garrard 1245 Signature 0175 Sontec 1165 Sony 0065, 0565, 0865, 1145 Staron 1235 STS 0025 Sylvania 0215 Symphnoic 0335 Tandy 0305 Tangberg 1195 Teac 0235, 0335, 0385, 0525, 0795, 0835, 1355 Technics 0055, 0605, 1095 Techwood 1325 Telefunken (E) 0505 Thomson (E) 0505 Toshiba 0035, 0685 Vector Research 0065, 1135 Victor 0315 Wards 0175 Yamaha 0005, 0015, 0575, 1065 TAPE DECK Aiwa Akai Carver Denon Fisher Garrard JVC Kenwood Magnavox Marantz Mitsubishi Onkyo Optimus Philips Pioneer Revox Sansui Sharp Sherwood Sony Teac Technics Victor Wards Yamaha 0094, 0214, 0224 0184 0094 0304 0144 0194, 0204 0274, 0284, 0294 0124, 0134, 0154, 0234, 0244, 0264 0094 0094, 0344 0184 0364, 0374 0034, 0064, 0204, 0334 0094 0034, 0044, 0064 0354 0094, 0344 0264 0334 0054, 0084, 0324 0194, 0254 0074, 0314 0294 0034 0004, 0014 MD RECORDER Yamaha 0024 iii 03V396code(UCA) 3 1/13/0, 11:52 AM UCA RX-V396 Natural Sound AV Receiver Ampli-tuner audio-vidéo YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA 00V396(UCA)-cv1/4 1 OWNER’S MANUAL MODE D’EMPLOI Printed in Malaysia ID V502730-2 9/28/0, 3:11 PM Quick Reference Card TAPE/MD AMP(TUNER) POWER A/B/C/D/E TEST POWER Input selector buttons Input selector buttons Input selector buttons Input selector buttons EFFECT PRESET+/– EFFECT EFFECT DISC SKIP+/– EFFECT DISC SKIP+/– VOLUME TV VOLUME SLEEP MUTE SLEEP TV INPUT PRG+, PRG– REC/PAUSE PLAY DIR A (TAPE) SKIP– (MD) SET MENU REWIND (TAPE) SEARCH (MD) +/– TIME LEVEL DVD/LD POWER POWER VOLUME MUTE CD VOLUME TV VOLUME MUTE VOLUME TV VOLUME DISPLAY (MD) SLEEP DECK A/B (TAPE) DISPLAY TV INPUT PAUSE (MD) PAUSE DIR B (TAPE) SKIP+ (MD) PLAY SKIP– FAST FORWARD (TAPE) SEARCH (MD) SEARCH STOP SKIP+ SEARCH STOP MUTE SLEEP PLAY SKIP– SEARCH TV VOLUME DISPLAY TV INPUT PAUSE SKIP+ SEARCH STOP V502990 Quick Reference Card VCR DVD MENU VCR POWER POWER DISC SKIP+/– VOLUME MUTE RETURN MENU SELECT MENU LEFT TITLE CBL/SAT TV CBL/SAT POWER TV POWER Numeric buttons CHANNEL CHANNEL CHANNEL CLEAR +10 EFFECT CHANNEL CBL/SAT ENTER CHANNEL+/– +100 CHANNEL ENTER EFFECT CHANNEL ENTER VCR CHANNEL+/– VOLUME TV VOLUME MUTE INDEX TV INPUT MENU UP TV SLEEP *1 VCR REC VCR PLAY MENU RIGHT MENU MENU DOWN VCR REWIND VOLUME TV VOLUME DISPLAY TV INPUT MUTE TV SLEEP TV CHANNEL+/– VOLUME TV VOLUME TV MUTE DISPLAY TV INPUT VCR PAUSE MENU SELECT MENU LEFT MENU UP VCR FAST FORWARD MENU VCR STOP RECALL *1 Press this button twice to start recording. Appuyer deux fois sur cette touche pour commencer l’enregistrement. Drücken Sie diese Taste zweimal, um die Aufnahme zu starten. Tryck två gånger på den här knappen för att börja spela in. TV SLEEP *1 VCR REC VCR PLAY TV VOLUME DISPLAY TV INPUT VCR PAUSE MENU RIGHT VCR REWIND MENU DOWN Premere due volte questo tasto per iniziare la registrazione. Presione dos veces este botón para empezar a grabar. Druk tweemaal op deze toets om met opnemen te beginnen. VCR FAST FORWARD VCR STOP V502990 Connection Guide (when listening to a digital 5.1-channel source) DVD player AUDIO OUT L R DIGITAL OUT VIDEO OUT R COAXIAL VIDEO OUT ANALOG AUDIO OUT L Main speakers A LD player OPTICAL COAXIAL DIGITAL OUT DOLBY DIGITAL RF OUT Main speakers B DOLBY DIGITAL RF OUT OPTICAL DIGITAL OUT R DOLBY DIGITAL RF IN L R L RF demodulator V C O COAXIAL DIGITAL OUT + R – MAIN – C + L A B SET BEFORE POWER ON CENTER R REAR (SURROUND) MAIN A OR B : 4W MIN. /SPEAKER A+B : 8W MIN. /SPEAKER L + + – – MAIN A OR B : 8W MIN. /SPEAKER A+B : I6W MIN. /SPEAKER (U.S.A. model) V L VIDEO IN Analog signal V Video signal R Signal flow O TV Monitor Subwoofer system R Center speaker L Rear speakers C Digital signal (optical) Digital signal (coaxial) V573010 396