Transcript
1 Preparations Accessories Check that the following accessories are supplied with this product.
AV Receiver
Easy Setup Guide
■ Remote control
■ Batteries (AAA, R03, UM-4) (x 2)
Insert into the remote control in the correct polarity (+/-).
■ YPAO microphone
■ VIDEO AUX input cover
■ AM antenna
■ FM antenna
English for U.S.A. *The figure of the supplied FM antenna differs depending on regions.
■ CD-ROM (Owner’s Manual)
■ Safety Brochure
■ Easy Setup Guide (this document)
Cables necessary for connections Th is do c u me n t e x p l ai n s h ow to s e t up a 5 . 1 - o r 7 . 1 - c h an n e l s ys t e m a n d p l a y b a c k s u r ro u n d s o un d of a B D /DV D o n thi s un it. For m o re i n fo r m a t i o n , re fe r t o “O w n e r ’s M a n u a l ” o n t h e s u p p l i e d CD - R OM . A P DF for ma t o f t h i s g u i d e a nd “O w n e r ’s M an u a l ” c a n b e d ow nl o a d e d from th e following website. http://dow nload.yamaha.com/
You need to separately prepare the following cables to build the system based on this document. ■ Speaker cables (depending on the number of speakers) ■ HDMI cable (x 2) ■ Audio pin cable (x 1) ■ Digital optical cable (x 1) (unnecessary if your TV supports ARC)
2 Placing the speakers Set up the speakers in the room by using the following diagram as a reference. For information on other speaker systems, refer to “Owner’s Manual”.
5.1-channel system
7.1-channel system
60° 60° 80°
80°
30 cm (1 ft) or more
60° 60° 80°
80°
Front speaker (L) Front speaker (R) Center speaker Surround speaker (L) Surround speaker (R) Surround back speaker (L) Surround back speaker (R) Subwoofer
2
En
3 Connecting the speakers/subwoofer • This unit is configured for 8-ohm speakers at the factory. When connecting 6-ohm speakers, set the speaker impedance of this unit to “6 Ω MIN”. For details, see “Setting the speaker impedance” (p.16) in “Owner’s Manual”.
the front speakers ( 1 Connect to the FRONT ( / ) terminals.
/
)
the center speaker ( 2 Connect CENTER terminal.
) to the
• Use a subwoofer equipped with built-in amplifier. • Remove the power cable of this unit from an AC wall outlet and turn off the subwoofer before connecting the speakers.
This unit (rear)
This unit (rear)
• Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP WIRES” will appear on the front display when this unit is turned on.
Connecting speaker cables Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive. a Remove approximately c 10 mm (3/8”) of + (red) b insulation from the ends of the speaker cable, a d and twist the bare wires – (black) of the cable together firmly. b Loosen the speaker terminal. c Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal. d Tighten the terminal. FR ON
Using a banana plug a Tighten the speaker terminal. b Insert a banana plug into the end of the terminal.
Banana plug
T
a
FR ON T
b
En
3
the surround speakers ( 3 Connect ) to the SURROUND ( / )
/
the subwoofer ( 4 Connect SUBWOOFER (1) jack.
terminals.
This unit (rear)
En
For 7.1-channel system Connect the surround back speakers ( ) to the SURROUND BACK ( / ) terminals.
This unit (rear)
Use an audio pin cable to connect the subwoofer ( ).
4
) to the
This unit (rear)
Audio pin cable
/
1 Connect the external devices to this unit.
4 Connecting the external devices
a Connect the BD/DVD player and this unit with an HDMI cable. If the BD/DVD player is currently connected to the TV directly with an HDMI cable, disconnect the cable from the TV and connect it to this unit.
TV
Audio out (optical)
HDMI in
HDMI out
HDMI
HDMI
OPTICAL
HDMI
O
b Connect the TV and this unit with another HDMI cable. c Connect the TV and this unit with a digital optical cable. This connection is required to play back TV audio on this unit. If your TV supports ARC (Audio Return Channel), this connection is unnecessary.
HDMI
b
c
BD/DVD player
a
d Connect the power cable to an AC wall outlet. HDMI
HDMI OUT 1 jack
HDMI HDMI 1
HDMI OUT 1
HDMI1 jack
(BD/DVD)
2 ARC
d DOCK
NETWORK
HDMI 1
HDMI OUT 1
HDMI 2
(BD/DVD)
HDMI 3
HDMI 4
HDMI 5
HDMI 6
To an AC wall outlet
HDMI 7
2 ARC
SIRIUS
SPEAKERS
ANTENNA
R
COMPONENT VIDEO
COMPONENT VIDEO AM
FM
FRONT
L
R SURROUND L
CENTER
R SURROUND BACK/
BI–AMP L
R ZONE 2/PRESENCE
L
REMOTE
PR
IN
PR SINGLE OUT
75Ω
PB
PB
VIDEO
• For information on how to connect radio antennas or other external devices, see “SETUP” in “Owner’s Manual”.
2 Turn on this unit, TV and BD/DVD player. the remote control of the TV, switch 3 With the TV input to display the video from this unit.
VIDEO
Y Y
MONITOR OUT
+12V 0.1A MAX. TRIGGER OUT
EXTRA SP SINGLE
L
The connections are complete. Move to the next page to optimize the speaker settings.
CENTER
L R
O
AV4 (OPTICAL) jack
R OPTICAL OPTICAL
COAXIAL
COAXIAL
(TV) AV 1
(CD)
(TV)
AV 2
AV 3
AV 4
OPTICAL AV 5
AV 6
AV OUT
AUDIO 1
AUDIO OUT
AUDIO 2
FRONT
ZONE 2 OUT
SURROUND
SUR. BACK
1 SUBWOOFER 2
PRE OUT
AV 4
This unit (rear)
NATURAL SOUND AV RECEIVER RX-V871
MAIN ZONE
PURE DIRECT
Turn on this unit ZONE 2
ZONE CONTROL
INFO
MEMORY
PRESET
CATEGORY FM
TUNING/CH
AM
VOLUME
INPUT SCENE
BD DVD
PHONES
SILENT CINEMA
USB
YPAO MIC
TONE CONTROL
TV
CD
PROGRAM
RADIO
VIDEO AUX
STRAIGHT
iPod/iPhone
HDMI IN
VIDEO
L
AUDIO
R
This unit (front)
En
5
5 Optimizing the speaker settings automatically (YPAO) By using the Yamaha Parametric room Acoustic Optimizer (YPAO) function, this unit automatically detects speaker connections and distances from the listening position, and optimizes the speaker settings such as volume balance and acoustic parameters to suit your room. • During the measuring process, the test tones are output at high volume. Take care that the test tone does not frighten small children. Also, refrain from using this function at night when it may be a nuisance to others.
MAIN
ZONE 2
CODE SET
HDMI
• During the measuring process, keep the room as quiet as possible.
1
2
3
4
• Do not connect headphones.
5
6
7
V-AUX
• If your subwoofer supports the auto-standby function, disable it.
1
2
3
4
5
6
AUDIO
DOCK
SIRIUS
NET
USB
PRESET
TUN./CH
• YPAO measurement is not performed correctly when any obstacles are in the room. • During the measuring process (about 3 minutes), keep stuff in the corners or remove it from the room.
AV
TUNER
• To cancel the operation, disconnect the YPAO microphone before starting the measurement.
CATEGORY FM
AM
INFO
MEMORY
MOVIE
MUSIC
SLEEP
PARTY
This unit (front)
start the measurement, use the cursor 2 To keys to select “Measure” and press
SUR. DECODE STRAIGHT
ENTER.
ENHANCER PURE DIRECT
SCENE BD DVD
Turned on the subwoofer and set the volume to half. If the cross-over frequency is adjustable, set it to maximum.
TV
CD
CROSSOVER/ HIGH CUT
RADIO
OPTION
ON SCREEN
VOLUME
ENTER
VOLUME
The following screen appears on the TV.
SOURCE RECEIVER
• During the measuring process, you cannot adjust the volume.
Preparing for YPAO
the YPAO microphone to the 1 Connect YPAO MIC jack on the front panel.
RETURN
DISPLAY
POP-UP MENU
TOP MENU
Cursor keys ENTER RETURN
The measurement will start in 10 seconds. The following screen appears on the TV when the measurement finishes.
MUTE
MODE HOLD
MIN
MAX
MIN
MAX
YPAO microphone Listening position
1
2
3
5
6
7
9
0
10
4
8
ENT
TV INPUT TV VOL
TV CH
HDMI OUT
MUTE
Ear height
Place the YPAO microphone at ear height in your listening position. We recommend using a tripod to adjust the height. You can use the tripod screws to fix the microphone in place.
6
En
• If any error message (such as E-1) or warning message (such as W-2) appears, see “Error messages” (p.39) or “Warning messages” (p.40) in “Owner’s Manual”. • If the warning message “W-1:Out of Phase” appears, see “If ‘W-1:Out of Phase’ appears” (next page).
the cursor keys to select 3 Use “Save/Cancel” and press ENTER.
If “W-1: Out of Phase” appears Follow the procedure below to check the speaker connections. Depending on the type of speakers or room environment, this message may appear even if the speakers are connected correctly.
the cursor keys to select “SAVE” and 4 Use press ENTER.
a Use the cursor keys to select “Result” and press ENTER. b Use the cursor keys to select “Wiring”. c Check the cable connections (+/-) of the speaker indicated with “Reverse”.
If the speaker is connected correctly: You can save the current settings. Press RETURN and proceed to step 3.
the YPAO microphone from 5 Disconnect this unit. Now optimization of the speaker settings is complete.
If the speaker is connected incorrectly: Turn off this unit, reconnect the speaker cable, and then try YPAO measurement again.
• Since the YPAO microphone is sensitive to heat, do not place the microphone in any place where it will be subjected to direct sunlight or high temperatures (top of an AV equipment, etc).
En
7
6 Playing back a BD/DVD Now let’s play back a BD/DVD. We recommend playing back multichannel audio (5.1channel or more) to feel surround sound produced by this unit.
Much more features! HDMI1 to select “HDMI1” as the 1 Press input source.
This unit has various other functions. Please refer to “Owner’s Manual” on the supplied CD-ROM and utilize this unit effectively.
VOL.
MAIN
ZONE 2
HDMI1
CODE SET
SOURCE RECEIVER
HDMI
1
2
3
4
5
6
7
V-AUX
1
2
3
4
5
6
AUDIO
DOCK
TUNER
SIRIUS
NET
USB
HDMI1
AV
L SL
SW C
R SR
2 Start playback on the BD/DVD player. STRAIGHT repeatedly to select 3 Press “STRAIGHT”. STRAIGHT
CATEGORY FM
AM PRESET
INFO
MEMORY
MOVIE
MUSIC
SLEEP
PARTY
TUN./CH
SUR. DECODE STRAIGHT
Select the desired sound program (CINEMA DSP) or surround decoder suitable for movies, music, games, sports programs and other uses.
• When “STRAIGHT” (straight decode) is enabled, each speaker produces each channel audio signal directly (without sound field processing). If you play back 5.1-channel audio on the 7.1-channel system, no sounds will be heard from the surround back speakers.
RADIO
ON SCREEN
VOLUME
R SR
STRAIGHT
ENHANCER PURE DIRECT
BD DVD
L SL
VOLUME
4 Press VOLUME to adjust the volume. VOL.
POP-UP MENU
MUTE
Volume -30.0dB
MODE HOLD
1
2
3
4
5
6
7
8
9
0
10
ENT
L SL
SW C
R SR
Now the basic setup procedure is complete.
If you cannot have surround sound
TV INPUT TV VOL MUTE
TV CH
HDMI OUT
Connect audio devices (CD player, etc.), game console, camcorder, and many others.
Selecting the sound mode (p.43)
VOL. SW C
Connecting other playback devices (p.26)
Only the front speakers work on multichannel audio Check the digital audio output setting on the BD/DVD player. It may be set to output 2-channel audio (PCM, etc.) only. No sound is heard from a specific speaker See “Troubleshooting” (p.114) in “Owner’s Manual”.
Playing back from iPod (p.57) By using a USB cable supplied with iPod, an optional Yamaha iPod dock or an optional Yamaha iPod wireless system, you can enjoy iPod music on this unit.
■ Listening to FM/AM radio (p.48) ■ Playing back music stored on a USB storage device (p.64) ■ Playing back the network contents (p.67 to p.70) ■ Selecting the input source and favorite settings at once (p.42) For more information, see “What you can do with this unit” (p.6).
© 2011 Yamaha Corporation
YD457A0/ESEN1
