Transcript
Pressure balance Valve Trim Instructions
Installation Considerations: • For best results, We recommends that this unit be installed by a
Owners Manual
licensed, professional plumber. • Please read over these instructions thoroughly before beginning installation. Make sure that you have all tools and supplies needed to complete the installation. • To prevent scald injury, the maximum output temperature of the shower valve must be no higher than 120°F. In Massachusetts, the maximum output temperature can be no higher than 112°F.
ASME A.112.18.1
• Keep this booklet and the receipt (or other proof of date and place of IS102-1-1
IS102-1-2
purchase) for this product in a safe place. The receipt is required should it be necessary to request warranty parts.
For easy installation of your Inolav® faucet you will need: · To READ ALL the instructions completely before beginning. · To READ ALL warnings,care, and maintenance information. Technical information:
You May Need
Recommended water pressure : 15 - 75 PSI Max. water pressure : 145 PSI Recommended hot water temp. : 120 - 140°F Max. hot water temp: 176°F Flow rate: Up 5.4 GPM@60 PSI Down 5.5 GPM@60 PSI
For warranty issues call us at 1-855 472 4304 or send us an e-mail at
[email protected]
For questions call us at 1-855 472 4304 or visit our website at www.inolav.com
1.Prepare wall for rough-in valve
Use a leveling indicator to align the valve into proper position. Make sure the valve is properly aligned in both the vertical and horizontal direction. At this step is also recommended to double check the dimensions given in step 1.
Finished wall must be within dimensions shown in figure 1. The distance between the back of the valve and the finished wall must be between 2.52” and 3.03”. Failure to comply with this tolerance will result in improper fitment of trim set.
X
X
3. Level the valve
2.52”~ 3.03”
Mixed water outlet 1
Threaded adapter (fitting) Hot water line Threaded adapter (fitting) Cold water line
Mixed water outlet 2
WARNING: Soldering directly onto the threaded nipples of valves might cause breakage or malfunctioning of the rough valve. Failure to follow these instructions will void the product’s warranty.
4. Check connections for leakage
2.Connect the water pipes
Using a screwdriver close the service stops located at each side of the main cartridge. Open the main water supply and inspect the connections for leakage.
Flush the cold and hot water line thoroughly before starting the installation. Use threaded adapters/fittings (not included) for connecting the water pipes to the rough valve. Never solder directly onto the threaded nipples of the rough valve. When soldering CxC connections, do not use excessive heat. It is not necessary to remove the pressure balance cartridge from the valve during normal soldering connection. The left side is the hot water inlet, the right side is the cold water inlet, up and down connections are the mixed water outlets.
Close Open
For warranty issues call us at 1-855 472 4304 or send us an e-mail at
[email protected]
For questions call us at 1-855 472 4304 or visit our website at www.inolav.com
5
4
5. Trim installation preparation
the way against the finish wall.
Make sure you have these spareparts
3 1
8. Install the escutcheon (1) slowly all
before you go to nextstep.
2
Pressure balance Valve mixerhandle(1), cap(2), handle screw(3), 6 7
9
8
10
diverter handle(4), plastic washer(5),
9. Install the handles Install the diverter handle (1) making
11
plastic washer(6), cap(7), handle screw(8), allen key(9),
sure plastic washer (4) is aligned as
escutcheon(10) 4
1
6. Remove the protective plastic cover (1) and (2)
that it travels from 9 to 3 o’clock (right to left) and vice versa. During
1
the midway point the diverter handle (1) should be pointing
2 3
2
shown. Adjust the diverter handle so
at 12 o’clock or up. When the diverter handle points to the left the upper outlet will be on
7. Open the service stops Use a screw driver in the counter clockwise direction to fully open the service stops. WARNING: Stop unscrewing the service stops once they have reached the full travel. Forcing the service stops past the limit can result in damage. Open
For warranty issues call us at 1-855 472 4304 or send us an e-mail at
[email protected]
and when it turns to the right the down outlet will go on. Install the handle(3) to the pressure balance cartridge and adjust handle(3) direction to the downward position. Then use the allen key to tighten the screws, and put on the screw caps.
For questions call us at 1-855 472 4304 or visit our website at www.inolav.com
Remove pressure balance
10. Test the handle Lift the handle up to adjust volume
Hot
cartridge:
control. Turn the handle left and right
1- Anti clockwise the sleeve(4).
to adjust water temperature. Turning
2- Using a spanner anti clockwise the
the handle to the right increases the
locking nut(5), then take it out. 3- Take out the pressure balance
cold water and to the left increases
Cold
cartridge (6).
the hot water. Clean the stops filters:
Install the diverter cartridge：
1- Using the spanner to anti clockwise stops (1).
1
1- Put diverter cartridge (3) to the
3
2
Valve, be noted the cartridge pin
2- Take out filter (2) and check Valve
1
2
3
should fix the hole of the valve.
(3). 3- Using clear water to rinse filter (2). 4- Slide filter (2) to check Valve (3),
4
5
7
2- Using a spanner clockwise locking nut (2). 3- Clockwise the sleeve(1).
then thread it to the valve body. 5- Using the spanner to connect stops (1)to the valve. 1
2
Remove the diverter cartridge： 1- Anti clockwise the sleeve(1).
4
cartridge: 1- Install pressure balance cartridge
3
5
Install the pressure balance
7
2- Using a spanner anti clockwise locking nut (2).
(6)to the valve. 2- Using a spanner clockwise the locking nut (5). 3- Clockwise sleeve (4) to the valve.
3- Remove the diverter cartridge(3).
For warranty issues call us at 1-855 472 4304 or send us an e-mail at
[email protected]
For questions call us at 1-855 472 4304 or visit our website at www.inolav.com
