Transcript
5101 AC Power Module COPYRIGHT Copyright 1990–97—Octagon Systems Corporation. All rights reserved. However, any part of this document may be reproduced provided that Octagon Systems Corporation is cited as the source. The contents of this document and the specifications herein may change without notice.
TRADEMARKS Octagon Systems Corporation®, the Octagon logo, Micro PC and the Micro PC logo are trademarks of Octagon Systems Corporation.
NOTICE TO USER The information contained in this document is believed to be correct. However, Octagon assumes no responsibility for any of the circuits described herein, conveys no license under any patent or other right and makes no representations that the circuits are free from patent infringement. Octagon makes no representation or warranty that such applications will be suitable for the use specified without further testing or modification. Octagon Systems Corporation general policy does not recommend the use of its products in life support applications where the failure or malfunction of a component may directly threaten life or injury. It is a Condition of Sale that the user of Octagon products in life support applications assumes all the risk of such use and indemnifies Octagon against all damages.
OCTAGON SYSTEMS® 6510 W. 91st Avenue Westminster, CO 80030
R
THE
COMPANY
Doc Order #2753 Rev 0497 Tech Support: 303–426–4521
5101 Power Module – 1
DESCRIPTION The 5101 AC power module provides power to the Octagon Micro PC. The module is a high-efficiency switcher with low noise output and cool operation. The unit is ideal for applications requiring varied AC output voltage. The 5101 delivers 40 watts of power. It has an input pulse noise filter. Internal catastrophic fusing prevents supply overloading. Components in the power module are UL and CSA approved, although these approvals apply only to the power module and not to completed assemblies.
SIDE VIEW
FRONT VIEW
ON/OFF SWITCH A
POWER RECEPTACLE
B
C
Figure 1—5101 Dimensions
5101 Power Module
A
5.35 in.
135.90 mm
B
4.45 in.
113.03 mm
C
2.0 in.
50.80 mm
5101 Power Module – 2
INSTALLATION 1.
Set the card cage so that you can read the lettering at the rear. The Octagon company information should be lined up vertically on the left side.
2.
Remove the card cage right side plate.
3.
Hold the power module with the on/off switch facing you. Bring the power supply to the right side of the card cage with the mounting studs facing left.
4.
Align the four mounting studs on the power module with the corresponding holes on the card cage plate. Insert the studs and secure with the 6-32 nuts.
5.
Align the side plate with the holes on the right side of the power module. Insert the 6-32 screws and tighten as necessary.
WARNING:
Be certain that you use the 6-32x5/16" screws provided with your power supply. Using screws longer than 5/16" will cause damage to the power supply and harm to its user.
6.
Connect the power cord into the power receptacle below the on/off switch.
7.
Plug the power cable into the Micro PC motherboard.
TECHNICAL SPECIFICATIONS Input Voltage 85 VAC to 264 VAC for all rated load conditions. Input Frequency Range 47 Hz to 440 Hz Input Surge Current 18A max. @ 132 VAC, 36A max. @ 264 VAC Output Voltage Adjustment +5V output, ±5% Output Power Range 0–40W @ 50° C Output Voltage and Current +5V @ 4A, ±12V @ 0.5A
5101 Power Module – 3
Ground Leakage Current 250 µA max. @ 110 VAC Environmental Specifications Operating Temperature: –40° to 50° C Relative Humidity: 5%–95% noncondensing Overvoltage Protection Threshold 6.25V, ±0.75V Conducted RFI Meets FCC, CE, and VDE Limits A and B. Holdup Time at Rated Output 12 mS @ 110 VAC Safety Approval Internal power supply (less enclosure, fuse, EMI filter, and power cord) UL, CSA, and VDE approved. Internal Fuse Metric (5 mm x 20 mm), 250V, 2A—fast blow Size 5.35 in. x 4.45 in. x 2.0 in.
PINOUTS Output Power Cable Pinout Pin #
Signal
1
+5V
2
+5V
3
Gnd
4
AGnd
5
+12V
6
-12V
5101 Power Module – 4
