Transcript
L ED WORK LAMP
LED Work Lamp
1
O peration and Safety Notes
2
3
7 4
Z 29618-BS
6
6
person responsible for their safety. Children must never be allowed to play with the device. J This product is not a toy and should be kept out of the reach of children. Children are not aware of the dangers associated with handling electrical products. J Do not use the article if you detect any kind of damage. J CAUTION! DANGER OF EXPLOSION! Do not operate the LED work lamp in potentially explosive environments in which there are inflammable vapours, gases or dusts. J The LED inspection lamp is protected against water spray. However, the product, mains adapter and car adapter must never be immersed in water or other liquids. Failure to observe this advice will create the risk of elecGB / IE
J
J J m
Q Introduction
Familiarise yourself with the product before using it for the first time. In addition please refer carefully to the operating instructions below and the safety advice. Use the product only as described and for the indicated purpose. Keep these instructions in a safe place. If you pass the product on to anyone else, please ensure that you also pass on all the documentation. Q Proper
use
The product is intended for providing illumination in dry indoor rooms and in outdoor environments. If used outdoors the mains adapter must be protected from moisture and the weather. Any other
5
use or modification of the product constitute improper use and pose a risk of short circuits, fire, electric shocks and damage to the product. The manufacturer is not liable for damage caused by improper use. The product is not intended for commercial use. Q Description
features
1 2 3 4 5 6 7
of parts and
Hook Magnetic mount Mains adapter Car adapter (for cigarette lighter socket) ON / OFF switch Power input connection socket Indicator LED
Q Technical
data
Light bulb: 23 LEDs (white, non-replaceable) Light intensity : approx. 12,000 mcd (millicandela) Lamp rechargeable batteries: 3 x AA NiMH, 1000 mAh (not replaceable) Charging time: approx. 4 to 6 hours Burn time: approx. 3 hours (with fully charged battery) Lifespan of LEDs: approx. 20,000 hours Protection class: System of protection: IP44 Adapter: Input: 230 V ~ 50 Hz Output: 6 V , 300 mA Model: YX-0603
Protection class: System of protection: IP20 Cigarette lighter: Input: 12 V Output: 12 V Q Scope
Safety instructions J
Warning! DANGER TO LIFE AND RISK OF ACCIDENTS FOR INFANTS AND CHILDREN! Never leave children alone and unsupervised with the packaging material. There is always a risk of suffocation if children play with the packaging material. Children often underestimate risks. Always keep children away from the packaging material. This product is not a toy. J Children or persons who lack the knowledge or experience to use the device or whose physical, sensory or intellectual capacities are limited must never be allowed to use the device without supervision or instruction by a
, 240 mA
of delivery
1 LED inspection lamp 1 Mains adapter 1 Car adapter for cigarette lighter socket 1 Magnetic mount 1 Operating instructions
GB / IE
GB / IE
GB / IE
GB / IE
GB / IE
tric shock! Never hang the product near a washbasin, pond and the like. Connect the LED work lamp to a properly installed mains socket or a suitable cigarette lighter socket only. The voltages in each case must comply with information given in the section “Technical data”. Ensure that the electrical socket is easily accessible so that you can pull the plug quickly out of the socket if necessary. Do not carry out any modifications or repairs to the product yourself. The LEDs cannot and must not be replaced. CAUTION! The protective surround to the LEDs cannot be replaced. Dispose of the LED inspection lamp if you discover cracks or signs of fracture on the protective surround.
J D ispose of the product if the LED inspection lamp, mains adapter or car adapter is damaged. J Never connect the LED work lamp to a power supply socket if the LED work lamp, power lead or socket is damaged or the LED work lamp has been dropped. J Ensure that the power lead cannot become damaged by sharp edges or hot objects. Unwind all the lead completely before use. J Keep easily flammable materials away the product. Never hang objects above the LED work lamp or the mains adapter and never cover them. J Pull the mains adapter / plug out of the mains socket / cigarette lighter socket when you are not using the LED work lamp or before you clean it. Do this as well if signs of a fault
develop during use or charging, e.g. smoke, burning smell etc., or during a storm. When doing this, pull directly on the mains adapter / plug and not on the lead. J Protect the product against heat, cold, strong vibrations and impacts. J CAUTION! LED RADIATION. Avoid damage to eyes! Never look directly at the LED. Never use optical appliances such as magnifying glasses or the like to look at the LED. Protect yourself and your environment by taking proper precautions. J Never point the LED beam at reflective surfaces, people or animals. This could result in blindness or irritation of the eyes. Even weak LEDs could result in eye damage.
J D o not attach the hook 1 to hot objects. The dead weight of the LED work lamp might cause the hook to deform or bend out of shape.
Note: You can charge the LED inspection lamp from an ordinary domestic mains power outlet or from the cigarette lighter socket in your vehicle. Tip: We recommend that you charge the LED inspection lamp from an ordinary domestic mains power outlet to avoid draining your vehicle’s battery. CAUTION! Do not connect the LED inspection lamp to the cigarette lighter socket of your vehicle if the vehicle battery is old or degraded. Failure
to observe this advice may result in your vehicle’s engine not starting. Note: To use the LED inspection lamp without an adapter, you must first charge the integral rechargeable batteries. It takes between 4 and 6 hours to charge the integral batteries. The rechargeable batteries are permanently installed in the handle of the LED inspection lamp. Note: Charge the LED inspection lamp for approximately 12 hours before first use. Note: Charge the LED inspection lamp at least once a month, if it is to remain unused for an extended period of time. Note: If the LED inspection lamp has not been charged for an extended period of time (approx. 2 months), you could find that the integral rechargeable batteries have entered a dormant state. Charge and discharge the LED inspection lamp a
number of times in succession to reactivate the integral rechargeable batteries. j Switch off the LED inspection lamp during the charging process (set the ON / OFF switch 5 to position 0). j Remove the rubber protection cap from the bottom of the LED inspection lamp. j Insert the power output connection plug of the mains adapter 3 or the car adapter 4 into the power input connection socket 6 in the handle of the LED inspection lamp. Note: During charging from a cigarette lighter socket, ensure that the plug is always completely inserted into the cigarette lighter socket of the vehicle. Failure to observe this advice may result in risk of fire from overheating. j Insert the mains adapter 3 into a mains socket or the car adapter 4 into the ciga-
GB / IE
GB / IE
GB / IE
GB / IE
GB / IE
GB / IE
Q Before
use
Q Charging
lamp
the LED inspection
rette lighter socket of your vehicle. Note: The product has an overcharging protection system. Nevertheless, you should disconnect the LED inspection lamp from the mains once the charging process is complete. Note: The indicator LED 7 illuminates red during the charging process. When the charging process is complete, the indicator LED 7 illuminates green. When the indicator LED 7 illuminates green, pull the mains adapter 3 out of the mains socket or the car adapter 4 out of the cigarette lighter socket. Disconnect the adapter from the LED inspection lamp to prevent the batteries from discharging themselves. j Place the rubber protection cap back on the power input connection socket 6 before you start to use the LED inspection lamp again.
Otherwise water could enter the power input connection socket 6 if the LED inspection lamp is used outdoors. Q Use
m CAUTION – RISK OF ACCIDENT! If at all possible, do not use the LED inspection lamp in a moving vehicle. If the LED inspection lamp is used in a vehicle, it must not be allowed to endanger the safety of the driver or passengers. Always store and secure the LED inspection lamp in such a way that there is no risk of injury from or damage to the product, even during full braking. Note: You can secure the LED inspection lamp in place using the hook 1 or magnetic mount 2 . Clamp the magnetic mount 2 to the LED’s pro-
GB / IE
Contact your local refuse disposal authority for more details of how to dispose of your worn-out product. T o help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority. Defective or exhausted rechargeable batteries must be recycled in accordance with Directive 2006 / 66 / EC. Return the battery and / or the device through the appropriate collection facilities.
GB / IE
tective surround. Then hold the LED inspection lamp against a magnetic surface. Q Using
the LED inspection lamp disconnected from a power supply
j F ully charge the LED inspection lamp, as described in the section on “Charging the LED inspection lamp”. j Set the ON / OFF switch 5 to position I to switch on the LED inspection lamp. j Set the ON / OFF switch 5 to position 0 to switch off the LED inspection lamp. Q Using
the LED inspection lamp connected to a power supply
m CAUTION! RISK OF INJURY! Position the power lead so that it does not create a trip hazard.
GB / IE
Pb
Improper disposal of rechargeable batteries can damage the environment!
m CAUTION RISK OF ACCIDENT! Do not connect or use the LED inspection lamp if you are in moving traffic, for example driving a vehicle. The LED inspection lamp is not intended to be used as an indoor lighting fixture or a reading lamp! j Remove the rubber protection cap from the power input connection socket 6 . j Insert the power output connection plug of the mains adapter 3 or of the car adapter 4 into the power input connection socket 6 in the handle of the LED inspection lamp. j Insert the mains adapter 3 into a 230 V ~ mains socket or the car adapter 4 into the cigarette lighter socket of your vehicle. j Set the ON / OFF switch 5 to position I to switch on the LED inspection lamp.
m C AUTION! If the LED inspection lamp is connected to the mains by the mains adapter 3 , in this state it is intended exclusively for indoor use. j Set the ON / OFF switch 5 to position 0 to switch off the LED inspection lamp.
GB / IE
GB / IE
GB / IE
Level of information: 11 / 2010 ID No.: Z29618-BS112010-6
Rechargeable batteries must not be disposed of with the household refuse. They may contain toxic heavy metals and require to be handled as special waste. The chemical symbols of heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead
© by ORFGEN Marketing IAN 58812 Milomex Ltd. c / o Milomex Services Hilltop Cottage Barton Road Pulloxhill Bedfordshire MK45 5HP UK
EMC Product Description: LED Work Lamp Model No.: Z29618-BS Version: 12 / 2010 GB / IE
GB / IE
Fault
Possible causes and cures
Q Maintenance
Indicator LED 7 does not illuminate
When connected to a cigarette lighter socket: - Is the cigarette lighter socket supplied with power? Some cigarette lighter sockets only supply power with the ignition switched on. - Check the fuse in the vehicle. When connected to a cigarette lighter socket: - Vehicle battery too weak?
The product requires no maintenance. The LEDs cannot be replaced. J Disconnect the product from the power supply before you clean it. J Never immerse the product in water or other liquids. J Do not use corrosive cleaning agents. j Clean the product regularly with a dry, flufffree cloth. Use a slightly moist cloth to remove any stubborn dirt.
Q Troubleshooting
Fault
Possible causes and cures
No functions
- Mains adapter 3 or car adapter 4 is not fully inserted.
Charging takes a very long time
and cleaning
Q Disposal
The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities. GB / IE
GB / IE
