Zis480nh Ge Monogram 48" Built-in Side-by-side Refrigerator Flush Inset Installation

Transcript

GE Monogram® 48" Built-In Side-by-Side Refrigerator ZIS480NH SECTION 1 FLUSH INSET INSTALLATION SECTION 2 STANDARD INSTALLATION 1/4" FRAMED PANELS 3/4" OVERLAY PANELS Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator OVERALL DIMENSIONS ZIS480NH FLUSH INSET INSTALLATION 25 7/8" (65.7) 20 5/8" (52.4) 50" (127.0) 11 5/16" (28.7) *72 3/16" (183.4) *83 1/2" * 83 1/2" (212.1) (212.1) 68 13/16" (174.8) SPECIFICATIONS Overall Width 50" (127.0 cm)† Overall Height 83 1/2" (212.1 cm) † Overall Depth 25 7/8" (65.7 cm) † Door Clearance 28 5/8" (72.1 cm) Cutout Width 51" (129.5 cm) Cutout Height 84 1/2" (214.6 cm) Cutout Depth 26 3/16" (66.5 cm) Plumbing Requirements 1/4" OD copper tubing or GE SmartConnect kit Shipping Weight 775 lb (351.5 kg) *3 3/8" *3" FRONT VIEW (8.6) (7.6) SIDE VIEW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84". 47" (119.4) Case width **13" **15" (33.0) (38.1) † Dimensions include 3/4" custom cabinet panel ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. 28 5/8" *115° Door swing (72.7) Doors can be adjusted to 90° door swing TOP VIEW ** Allow 4" (10.2) min clearance to a wall for 90˚ door swing ** Allow 4" (10.2) min clearance to a wall for 90˚ door swing ** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances. ZIS480NH Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator FLUSH INSET INSTALLATION 3/4" PANELS 47 1/2" (120.7) 6" (15.2) 20 15/16" (53.2) FLUSH INSET INSTALLATION TOP VIEW 24" (61.0) 1 1/2" Case 3 1/4" Finished cleats(8.3) 5 1/4" (13.3) 20" (50.8) Case Trim 5" (12.7) 51" (129.5) Flush inset width 49 1/2" (125.7) 3/4" (1.9) Width of side cleats Width between cleats (212.1-214.6) *Trim will overlap additional 7/16" 6" 5" 75" 84 1/2" WARNING: 75" (190.5 ) From floor to bottom of electrical area (214.6) 5" The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. (56.5) 84 1/2" (214.6) B Water supply area. 22 1/4" (12.7) (190.5 ) From floor to bottom of electrical area Finished cleats A E (15.2) 5" 3 1/2" (12.7) (12.7) (8.9) 7" WATER 7" (17.8) (17.8) FRONT VIEW 3 1/2" W B (8.9) WATER ANTI-TIP BRACKET 2" x 4" SOFFIT Cut to 35" Length D FLUSH INSTALLATION ZISB480DH Screws mounted into vertical wall studs *84" (213.4) *Or installation height from floor SIDE VIEW INSTALLED UNDER SOFFIT 3 1/2" W 3 1/2" (8.9) SIDE VIEW FRONT VIEW C NOTES A M  ounting the junction box in this location will also allow for front accessability through access panel. 1/2" (1.3) 3/4" Panel *83 1/2" min Depth to cleat *84 1/2" max SIDE VIEW 7/16" (1.1) Trim overlap (3.8) Door E 26 3/16" (66.5) Flush inset depth ZIS480NH (8.9) The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. Determine your installation construction and required anti-tip configuration: C C  ut a 1/2” x 4” block 35” long. Measure and mark under the soffit, 5 1/4” from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84”. D W  ooden Wall Studs and No Soffit • Cut a 2” x 4” block and secure to brackets provided. • Secure brackets to back wall of opening at 84” or your installation height from the floor. See Installation Instructions for detailed instructions. SIDE VIEW INSTALLED WITH WOODEN WALL STUDS AND NO SOFFIT ZISB480DX Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator FLUSH INSET 3/4" PANEL DIMENSIONS NOTES 1/4" Router Cut Depth for Hinge Clearance B Grille Panel D FLUSH INSET INSTALLATION PANEL ASSEMBLY CROSS SECTION A Trimmed refrigerators are designed to be customized with decorative panels.  Fieldinstalled 3/4” custom door and grille panels are required. Adjustment brackets allow 1/8” fine adjustment of panel position in 3 dimensions. Use templates provided to locate mounting brackets on the door and grille panels. Door E 3/4" Flush Inset Panel PANEL ASSEMBLY CROSS SECTION HINGE CLEARANCES ROUTER 1/4" DEEP C Freezer Panel Maximum total panel weight: • Fresh food door panels – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs HINGE CLEARANCE Z Fresh Food Panel Y X X Y Z 1 1/4" 1" 1/2" 50" B C Door Handles Door handle not included.  A custom handle supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4” panels.  Kit includes one handle – 30 1/2” long. PANEL DIMENSIONS A ZIS480NH D 10 5/8" 68 13/16" 20 7/8" E 28 7/8" ZKHSS2: European tubular stainless steel handle designed to fit 3/4” panels.  Kit includes one handle – 64 1/4” long. Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator ZIS480NH OVERALL DIMENSIONS STANDARD INSTALLATION 25 1/2" (64.8) 25 1/2" (64.8) 23 7/8" (60.7) 23 7/8" (60.7) 48" (121.9) 48" (121.9) 1 3/4" 1 3/4" (4.4) (4.4) *84" *83 1/2" *83(212.1) 1/2" *84" (213.4) (213.4) (212.1) 68 1/2" 68 (174.0) 1/2" (174.0) *72 1/4" *72(183.5) 1/4" (183.5) SPECIFICATIONS Overall Width 48" (121.92 cm) Overall Height 84" (213.36 cm) Overall Depth 25 3/8" (64.453 cm) Door Clearance 28 5/8" (72.1 cm) Cutout Width 47 1/2" (120.7 cm) Cutout Height 83 1/2" - 84 1/2" (212.1 - 214.6 cm) Cutout Depth 24" (61 cm) Plumbing Requirements 1/4" OD copper tubing or GE SmartConnect kit Shipping Weight 775 lb *3 3/4" *3 3/4" (9.5) (9.5) FRONTVIEW VIEW FRONT *3 1/2" *3 1/2" (8.9) * Shipping height. Use leveling legs and wheels for maximum * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. 1" height adjustment from shipping height. (8.9) SIDEVIEW VIEW SIDE 47" (119.4) 47" (119.4) Case width Case width ** Allow 15" (38.1) min ** Allow 15" (38.1) min clearance for 130˚ clearance for 130˚ door swing door swing ** Allow 20" (50.8) min ** Allow 20" (50.8) min clearance for 130˚ clearance for 130˚ door swing door swing ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. 28 5/8" 28 5/8" (72.7) TOPVIEW VIEW TOP ** Allow 4" (10.2) min **clearance Allow 4"to(10.2) min a wall for 90˚ clearancedoor to a swing wall for 90˚ door swing (72.7) ** Allow 4" (10.2) min **clearance Allow 4"to(10.2) min a wall for 90˚ clearancedoor to a swing wall for 90˚ door swing ** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door ** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow full 130° door swings for pan removal. If the 90° door stop position is used, pan access is full 130° door swings for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted. maintained, but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due toZIS480NX manufacturing tolerances. ZIS480NX Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator ZIS480NH STANDARD INSTALLATION STANDARD INSTALLATION TOP VIEW 24" (61.0) 47 1/2" (120.7) 3 1/4" (8.3) 20" (50.8) 3 1/8" (7.93) 24" (61) 6" (15.2) 1 9/16" (3.8) E A M  ounting the junction box in this location will also allow for front accessability through access panel. 47 1/2" (120.7) 22 3/4" (57.8) A 7/16" (1.1) Trim overlap 5" (3.97) NOTES 7/16" (1.1) Trim overlap 1 1/2" (12.7) 6" *83 1/2" min *84 1/2" max E (15.24) (212.1-214.6) *Trim will overlap additional 7/16" B Water supply area. 5" WARNING: (12.7) The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. 75" (190.5 ) From floor to bottom *84 1/2" of electrical area (214.6) *Trim will overlap additional 7/16" 5" 75" (190.5 ) From floor to bottom of electrical area 5" 3 1/2" (12.7) (12.7) (8.9) 5" 5" (12.7) WATER 3 1/2" (12.7) B (8.9) FRONT VIEW W 3 1/2" W(8.9) WATERSIDE VIEW FRONT VIEW SIDE VIEW 3 1/2" (8.9) The refrigerator will project forward, slightly beyond adjacent cabinetry. ANTI-TIP BRACKET 2" x 4" C SOFFIT Cut to 35" Length D E *84" (213.4) STANDARD INSTALLATION *Or installation height from floor ZISB480DH 3/4" Min. Top Case Trim Side View Top Case Trim Install Screws Through Trim and Into 3/4" Min. Wood Brace SIDE VIEW INSTALLED WITH WOODEN WALL STUDS AND NO SOFFIT ZISB480DX Determine your installation construction and required anti-tip configuration: C Installed Under Soffit After installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exeed 24” deep. The top case trim overlaps the bottom of the soffit. D W  ooden Wall Studs and No Soffit • Cut a 2” x 4” block and secure to brackets provided. • Secure brackets to back wall of opening at 84” or your installation height from the floor. Screws mounted into vertical wall studs SIDE VIEW INSTALLED UNDER SOFFIT The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. FRONT VIEW INSTALLED WITH METAL WALL STUDS AND NO SOFFIT E M  etal Wall Studs and No Soffit This method requires securely fastened cabinets on both sides and a ¾” minimum wood brace above unit, with it’s front surface 24” from back wall. • After installing unit into opening, raise grille panel and attach metal case top trim to ¾” minimum wood brace. • The brace spanning the enclosure must be securely fastened to cabinets on both sides. See Installation Instructions for detailed instructions. Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator CUSTOM SIDE PANELS ZIS480NH STANDARD INSTALLATION F 24" (61.0) NOTES 3/16" (.5) 1 7/8" (4.8) *84” *84" (213.4) *Depending on installation height F S  ide panels must be used whenever the sides of the refrigerator will be exposed. The 1/4” side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. *3" - 4" (7.6 - 10.2) *Depending on installation height 2 9/16" (6.5) XRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH XRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator 1/4" FRAMED PANEL DIMENSIONS STANDARD INSTALLATION NOTES PANEL ASSEMBLY CROSS SECTION A D Trim B Grille Panel Trimmed refrigerators are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. Door E 1/4" Framed Panel Supplied Handles PANEL DIMENSIONS C 1/4" Framed Panel A B C 45 7/8" 9 1/2" 68 3/8" D E 18 9/16" 26 9/16" Maximum total panel weight: • Fresh food door panel – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs 3/4” Overlay Panels: Order trim kit #ZKT48SSH for 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. 3/4" OVERLAY PANEL DIMENSIONS The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. PANEL ASSEMBLY CROSS SECTION A B Grille Panel Trim Door 1/4" Backer Panel E Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel. 3/4" Overlay Panel .10" Spacer Panel NOTE: Left-to-right offset is not always equal to top-to-bottom offset. Supplied Handles PANEL DIMENSIONS C Freezer Panel 1/4” Framed Panels: Order trim kit #ZKT48SSH for 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Fresh Food Panel Freezer Panel D ZIS480NH Fresh Food Panel A B C 1/4" Backer Panel 45 7/8" 9 1/2" 68 3/8" .10" Spacer Panel 45" 8 5/8" 67" 3/4" Overlay Panel 46 1/8" 9 3/4" D E 18 9/16" 26 9/16" 17 1/4" 25 1/4" 68 5/8" 18 13/16" 26 13/16" .25" + .10" + .75" = 1.10" Total Panel Thickness Maximum total panel weight: • Fresh food door panel – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle. Order 2 kits for sideby-side refrigerators from your Monogram suppplier. Product Specification Created 8/14 GE Monogram® 48" Built-In Side-by-Side Refrigerator ZIS480NH FEATURES AND BENEFITS Halogen Light Columns - Located in the freezer and fresh food compartments, extend the full length of the interior compartments providing brilliant, all-level illumination LED Lighting - Located at the top of the fresh food compartment, and inside the vegetable and climate-control drawers, illuminates contents without compromising space Advanced Temperature Management System with Multi-Shelf Air Tower - Provides even distribution of air throughout the refrigerator Climate-Control Drawer - Allows you to expresschill beverages, express-thaw meats and select specific temperatures for perishable foods Dispenser with Proximity Sensor - Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away Dairy Bin with Center Divider - Has a unique magnetic seal that locks in freshness Filter-Change Indicator Light - Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser GE® Water Filter - Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight Drop-Down Shelf - Provides additional space for a casserole dish or pizza box R Product Specification Created 8/14