Zo3000.1d Zo5000.1d Zo8000.1d 4 Channel Amplifiers Zo1500.4

Transcript

LIMITED TWO MONTH CONSUMER WARRANTY AND ONE YEAR CONSUMER WARRANTY WHEN PURCHASED AND INSTALLED FROM AUTHORIZED ORION DEALER Electronics Limited Warranty Please keep your original box. Orion warrants this product to be free from defects in materials and workmanship under normal use for a period of TWO (2) months from the date of original purchase receipt. When purchased and installed from an AUTHORIZED ORION dealer it is warranted for a period of ONE (1) Year from the date of the original purchase receipt. The ORIGINAL Receipt must be provided for all claims. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the warranty period. ORION will repair or replace (at its discretion) the defective merchandise with equivalent merchandise with equivalent merchandise at no charge. Warranty replacements may have cosmetic scratches or blemishes. Discontinued products may be replaced with more current equivalent products. This warranty is valid only to the original purchaser and is non-transferable to any other person or party. Any applicable implied warranties are limited in duration to a period of the express warranty provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore these exclusions may not apply to you. This warranty gives you specific legal rights; however you may have other rights that vary from state to state. What to Do if you need Warranty or Service Defective merchandise should be returned to your local authorized ORION dealer for warranty service. Assistance locating an authorized dealer can be found at the products main website www.orioncaraudio.com or by contacting ORION directly at 1-855-475-6048.If it becomes necessary for you to return DEFECTIVE merchandise directly to ORION, call the ORION Customer Care number at 1-855-475-6048 for a Return Merchandise Authorization (RMA) number. Package all defective items in the original container or in a package that will prevent shipping damage. The shipping address and instructions will be given to you by our customer care representative upon their issuing the RMA number. The RMA number must be clearly marked on the outside of the package. Please return only defective components. The return of functioning items increases your return freight charges. NON- DEFECTIVE items will not be exchanged.You will be contacted by customer care advising you of such situations, and product will be returned to you upon your payment of freight charges for the return of such product back to you. Include a copy of the original receipt with the PURCHASE DATE clearly visible, and a ROOF of PURCHASE statement listing the CUSTOMERS NAME, DEALER's NAME and INVOICE number, and product purchased. Warranty expiration on items without ROOF of PURCHASE will be determined from the type of sale and manufacturing date code. FREIGHT on defectives products returned must be PREPAID by you or your authorized dealer; items sent freight collect, or COD will be REFUSED. What is not covered? The warranty is valid only if the product is used for the purpose for which it was designed and does NOT COVER the following; Damage due to improper installation and sound settings, excessive or insufficient voltage spikes, and use of inferior low grade wiring. Subsequent Damage to other components Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV Radiation. Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be considered abuse. Any cost or expense related to the removal or installation of product. No Installation Fee reimbursements. Items previously repaired or modified by any unauthorized repair facility Return shipping costs from ORION to you on non-defective items Products with tampered or missing barcode labels Products returned without a Return Merchandise Authorization (RMA) number Freight Damage The cost of shipping product to ORION, from you to Orion Service performed by anyone other than Orion Damage related to Acts of Nature, lightning, hurricanes, flood, tornadoes, and wildfires. Products Sold outside of United States have NO WARRANTY expressed or implied How long will it take? ORION strives to maintain a goal of 7 day service for all electronics products (amplifiers, equalizers , electronic crossovers, etc.) returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these Steps may void your warranty. Any questions can be directed to the ORION Customer Care Department at 1-855-475-6048. 5 CHANNEL AMPLIFIERS ZO6000.5 4 CHANNEL AMPLIFIERS ZO1500.4 ZO2000.4 ZO3000.4 ZO4000.4 ZO5000.4 ZO6000.4 2 CHANNEL AMPLIFIERS ZO1000.2 ZO1500.2 ZO2500.2 ZO4500.2 MONOBLOCK CLASS D 1 OHM AMPLIFIERS ZO30 00.1D ZO50 00.1D ZO800 0.1D TABLE OF CONTENTS SPECIFICATION CLASS D MONO 1 OHM CHANNEL POWER DESCRIPTION ZO3000.1D ZO5000.1D ZO8000.1D RMS Watts @ 4 Ohm Mono 14.4V 245 400 600 RMS Watts @ 2 Ohm Mono 14.4V 425 780 1000 RMS Watts @ 1 Ohm Mono 14.4V 750 1250 2000 Watts Nominal 1500 2500 4000 Max Music Power Watts 3000 5000 8000 Frequency Response 10Hz~400Hz(-3dB) 10Hz~400Hz(-3dB) 10Hz~400Hz(-3dB) Signal Noise Ratio 90dB 90dB 90dB Input Impedance 22K Ohm 22K Ohm 22K Ohm Input Sensitivity 150mV~5V 150mV~5V 150mV~5V T.H.D. <0.05% <0.05% <0.05% Subsonic 25Hz 25Hz 25Hz Low Pass Freq. 15Hz-400Hz 15Hz-400Hz 15Hz-400Hz Bass Boost 0~+18dB 0~+18dB 0~+18dB Phase 0 / 180 0 / 180 0 / 180 Supply Voltage 11~15V DC 11~15V DC 11~15V DC Dimensions(mm) 320x231.5x55.5 357x231.5x55.5 392x231.5x55.5 O O O 28 O O O Table Of Contents......................................................................... ......1 Introduction................................................................................. .......2 Installation Instructions...................................................................... .2 Record Your Serial Number and Date.................................................... 2 Functions....................................................................................... 3~4 Operation ...........................................................................................5 Trouble Shooting.......................................................................... ...... 5 Precautions ........................................................................................6 Fuse Replacement.............................................................................. 6 Stereo Mode ...................................................................................7~8 Speakers Connections....................................................................9~13 Speaker Connections At Bridged....................................................14~17 Bridged Mode.............................................................................. 18~20 Power Connection Leads................................................................... 21 Wiring Instructions............................................................................ 22 Operation .........................................................................................23 Interference ......................................................................................24 Specification ...............................................................................25~28 1 INTRODUCTION SPECIFICATION Thank you for purchasing our car audio amplifier. These power amplifier has been designed to provide high quality performance with minimum maintenance. However, it's performance will only be as good as the care and quality of components with which is installed. We therefore advise that you read these instructions very carefully to familiarize yourself with the product and it's features. Before installing the power amplifier please read this instruction manual carefully. The instructions for mounting and connecting the set have to be followed precisely. If necessary, a service center should be consulted. All connection for DC power, signal input and speaker outputs can be carried out easily and safely by way of RCA and screwed terminals. FIVE CHANNEL POWER DESCRIPTION ZO6000.5 RMS Watts @ 4 Ohm Stereo 14.4V 100 X4 RMS Watts @ 2 Ohm Stereo 14.4V 150 X 4 RMS Watts @ 4 Ohm Bridge 14.4V 300 X 2 Watts Nominal 4 TH Channel Section 1200 Max Power 4 TH Channel Setion 2400 Frequency Response INSTALLATION INSTRUCTIONS Please choose a mounting place without any direct weather influences. Note that the amplifier generates heat so that a well ventilated place is necessary. According to your car's construction the set can be made very carefully in order to ensure the amplifier's full performance and reliability. Keep the wire connections as short as possible with sufficient length in order to minimize power losses and provide a higher audio output of the system. For safety reasons route all power and speaker wiring by using the exiting wire channels. 10Hz~36KHz(-3dB) Signal Noise Ratio 90dB Input Impedance 22K Ohm Input Sensitivity 250mV~5V <0.05% T.H.D. Hi pass Freq. 50Hz-4KHz RMS Watts @ 4 Ohm Mono 14.4V 260 RMS Watts @ 2 Ohm Mono 14.4V 450 RMS Watts @ 1 Ohm Mono 14.4V 900 To minimize damage to the cables, take care that they do not pass sharp edged metal. Class D Section Watts Nominal 1800 Total Amplifier Watts Nominal 3600 Lay all cables as far away as possible from the ignition cables, modules in the boot and under the key dashboard, as these create interference. Max Music Power Watts Frequency Response Add a fuse into the (+) power cable in a distance of not more than30cm from the positive battery pole. Keep the length of the power wires as short as possible . It is better to use power cables which are short and then longer speaker cables. In order to reduce interference , please pay attention to the wiring instructions. RECORD YOUR SERIAL NUMBER AND DATE To ensure your warranty, please record the following information regarding your new amplifier. 6000 10Hz~400Hz(-3dB) Signal Noise Ratio 90dB Input Impedance 22K Ohm Input Sensitivity 150mV~5V <0.05% T.H.D. Low pass Freq. 15Hz-400Hz 0~+18dB Bass Boost Supply Voltage 11~15V DC Dimensions(mm) 527x231.5x55.5 Model: Serial Number: Date of Purchase: Purchased from: 2 27 FUNCTIONS SPECIFICATION TWO CHANNEL POWER DESCRIPTION ZO1000.2 ZO1500.2 RMS Watts @ 4 Ohm Stereo 14.4V 70 X 2 105 X 2 RMS Watts @ 2 Ohm Stereo 14.4V 125 X 2 175 X 2 RMS Watts @ 4 Ohm Bridge 14.4V 250 350 Watts Nominal 500 750 Max Music Power Watts Frequency Response 1000 1500 10Hz~36KHz(-3dB) 10Hz~36KHz(-3dB) Signal Noise Ratio 90dB 90dB Input Impedance 22K Ohm 22K Ohm Input Sensitivity 250mV~5V 250mV~5V T.H.D. <0.05% <0.05% Hi Pass Freq. 50Hz-400Hz 50Hz-400Hz Low Pass Freq. 50Hz-400Hz 50Hz-400Hz Bass Boost 0/6/12dB 0/6/12dB Supply Voltage 11~15V DC 11~15V DC Dimensions(mm) 237X231.5X55.5 247X231.5X55.5 ZO6000.5 HPF FULL 50Hz 4KHz MODE Min Max HPF FULL HI INPUT INPUT CH3/CH4 GAIN HPF R + - - + CH3/CH4 HI INPUT + - - + CH2 CH4 GAIN + - - + L/R PWR PRO Min CH5 Max L 50Hz 4KHz HPF Min 15Hz Max MODE GAIN CH1/CH2 CH1/CH2 CH1 CH3 ZO6000.5 400Hz LPF 0dB +18dB REMOTE BASS BOOST CH5 ZO3000.1D/ZO5000.1D/ZO8000.1D TWO CHANNEL POWER DESCRIPTION ZO2500.2 ZO4500.2 RMS Watts @ 4 Ohm Stereo 14.4V 225 X 2 400X 2 PWR LINE OUT LINE INPUT BRIDGED R RMS Watts @ 2 Ohm Stereo 14.4V 315 X 2 630 X 2 RMS Watts @ 4 Ohm Bridge 14.4V 625 1375 Watts Nominal 1250 3750 Max Music Power Watts Frequency Response 2500 4500 10Hz~36KHz(-3dB) 10Hz~36KHz(-3dB) PRO IN Min Max GAIN OFF 25Hz SUB SONIC 0O 180 O 15Hz 400Hz 0dB +18dB PHASE L Signal Noise Ratio 90dB 90dB Input Impedance 22K Ohm 22K Ohm Input Sensitivity 250mV~5V 250mV~5V T.H.D. <0.05% <0.05% Hi Pass Freq. 50Hz-400Hz 50Hz-400Hz Low Pass Freq. 50Hz-400Hz 50Hz-400Hz Bass Boost 0/6/12dB 0/6/12dB Supply Voltage 11~15V DC 11~15V DC Dimensions(mm) 297X231.5X55.5 450X231.5X55.5 26 Input Mode Gain control LPF / HPF control Mosfet power supply 1~5 Channel Power Amplifier LPF BASS BOOST REMOTE OUT Sub Sonic control Bass Boost control Thermal protection LED Power and Protection Indicator Low Input and High Input Selected 3 FUNCTIONS SPECIFICATION ZO1500.4/ZO2000.4/ZO3000.4/ZO4000.4/ZO5000.4/ZO6000.4 MODE LPF HPF HPF 50Hz 400Hz LPF INPUT CH3/CH4 BASS BOOST FULL CH4 INPUT CH2 CH1/CH2 MODE CH2 GAIN 12 50Hz OUTPUT 6 400Hz HPF GAIN FULL 0 HI INPUT Min PWR Max Min CH3 CH1 Max PRO HPF HI INPUT 50Hz 400Hz CH1 CH3 + - - + CH4 CH1 + - - + CH2 FOUR CHANNEL POWER DESCRIPTION ZO1500.4 ZO2000.4 ZO3000.4 RMS Watts @ 4 Ohm Stereo 14.4V 75X 4 90 X 4 125 X 4 RMS Watts @ 2 Ohm Stereo 14.4V 90 X 4 125 X 4 190 X 4 RMS Watts @ 4 Ohm Bridge 14.4V 180 X 2 250 X 2 380 X 2 Watts Nominal 750 1000 1520 Max Music Power Watts Frequency Response 1500 2000 10Hz~36KHz(-3dB) 10Hz~36KHz(-3dB) 10Hz~36KHz(-3dB) 3000 Signal Noise Ratio 90dB 90dB 90dB Input Impedance 22K Ohm 22K Ohm 22K Ohm Input Sensitivity 250mV~5V 250mV~5V 250mV~5V T.H.D. <0.05% <0.05% <0.05% Hi Pass Freq. 50Hz-400Hz 50Hz-400Hz 50Hz-400Hz Low Pass Freq. 50Hz-400Hz 50Hz-400Hz 50Hz-400Hz Bass Boost 0/6/12dB 0/6/12dB 0/6/12dB Supply Voltage 11~15V DC 11~15V DC 11~15V DC Dimensions(mm) 330X231.5X55.5 362X231.5X55.5 372X231.5X55.5 ZO1000.2/ZO1500.2/ZO2500.2/ZO4500.2 FOUR CHANNEL INPUT R L HI INPUT OUTPUT R L + - - + L R BASS BOOST 0 Min MODE LPF GAIN 6 12 Max FULL 50Hz 4 HPF 400Hz LPF HPF 50Hz 400Hz PWR PRO POWER DESCRIPTION ZO4000.4 ZO5000.4 ZO6000.4 RMS Watts @ 4 Ohm Stereo 14.4V 175 X 4 185 X 4 250 X 4 RMS Watts @ 2 Ohm Stereo 14.4V 250 X 4 315X 4 375 X 4 RMS Watts @ 4 Ohm Bridge 14.4V 500 X 2 625 X 2 750 X 2 Watts Nominal 2000 2500 3000 Max Music Power Watts Frequency Response 4000 5000 10Hz~36KHz(-3dB) 10Hz~36KHz(-3dB) 10Hz~36KHz(-3dB) 6000 Signal Noise Ratio 90dB 90dB 90dB Input Impedance 22K Ohm 22K Ohm 22K Ohm Input Sensitivity 250mV~5V 250mV~5V 250mV~5V T.H.D. <0.05% <0.05% <0.05% Hi Pass Freq. 50Hz-400Hz 50Hz-400Hz 50Hz-400Hz Low Pass Freq. 50Hz-400Hz 50Hz-400Hz 50Hz-400Hz Bass Boost 0/6/12dB 0/6/12dB 0/6/12dB Supply Voltage 11~15V DC 11~15V DC 11~15V DC Dimensions(mm) 382X231.5X55.5 392X231.5X55.5 512X231.5X55.5 25 INTERFERENCE OPERATION All cables are sources of interference. The power cable and RCA audio cable are very prone to interference; the remote cables are less prone . There is often interference caused by the generator (piping), ignition ( cracking ) or other car electronic parts. Most of these problems can be eliminated by correct and careful cabling. In doing so, these are the following guidelines : Use only a screened audio cable for the wiring between " low level in " of the amplifier and RCA or DIN output of the radio . Lay the signal, speaker and power cables separately with enough distance from one another and also from each other car cable. lf not possible, you can lay the circuit and ground cable together with the serial cables. Audio and speaker cable should be as far away from these as possible. The REM cable to the automatic antenna output of the radio can be laid together with the signal cables. Avoid ground loops by laying the ground wiring of all components to a center point in a star-like way. You can find the best central point in measuring the voltage directly at the battery. Now compare this voltage value with the chosen ground point and the (+) terminal of the amplifier. lf the measured voltage in only less different you've found the correct central.Otherwise you have to look for another point. You should measure with the ignition being switched on and additionally switched on other electronics ( rear window heating and light ). If there are pickups from external electrical sources into the speaker cables, divide the core leads and twist them together. If there are noises from the car electronics. Add an interference suppression choke to the power wiring . If there are huming noises, use thicker ground cables or add further ground cables to the chassis. To reduce contact resistance and bad and loose contacts, please tin the cable ends or use multi core cable ends, spade terminals or others. Gold Plated spade terminal are free of corrosion and have the lowest contact resistance. Should all these measures to without any success. the use of a ground loop isolator may solve the problem. 24 GND(-)=GROUND CONNECTION Connect the GND terminal to the chassis ground of your car and take care of best electric and mechanic contact. In doing so, drill a hole in to the car chassis near the amplifier then remove color, dirt or any other substance from the ground point. After that fasten the cable end with added ring terminal by using a screw. Ensure that the ground connection is as short as possible and that the cable diameter is sufficient ( min 4 mm" ). Route the ground cables from the radio and all other equipment parts. like equalizer. active crossover network or other amplifiers, to the same ground point. +12V=POWER SUPPLY Connect the +12V terminal to the positive pole of the battery with a lead cable and add a fuse in to the power cable in a distance of not more then 30 cm from the battery. The lead cables's diameter should be at least 4 mm' for a length of 3m and 6 mm" for a length of 6m. REM(ON/OFF)REMOTE CONTROL Connect the REM terminal to the automatic antenna connector of your car radio. Now when turning on and off your car radio. the amplifier automatically switches ON and OFF. A cable diameter of 0.5mm is sufficient. FUSE The amplifier is equipped with a plug-in auto fuse protecting the set against fault conditions. Do not use a fuse with a higher value and never bridge the fuse over, as this may lead to irreparability damage so that ant any claim for warranty is denied. TROUBLE SHOOTING No Function: The connection cable is not connected correctly ( = terminal BATT/GND /REM). Ensure that all connections and mechanic contact and that the jacket has been removed. The fuse is defective-pay attention to the correct value of a new fuse! No Sound: Speaker cable or speaker plug are not connected correctly. No Sound /Red LED Protection Shines: The plus and minus wires of the speaker cable have contact, thus eliminate the short circuit. If you use a 2 Ohm speaker in stereo mode, a 4 Ohm speaker in bridge mode or tri-mode and the se t is overloaded, then turn the gain control to "min " until the operation is free of trouble. Poor Sound Quality ( Distortions ): The speakers are overloaded, therefore turn down the volume level and check the volume control positions. No Stereo Sound And A Weak Bass: Speaker cables (+) and (-) are mixed up, unit wired out of phase. 5 PRECAUTIONS OPERATION This unit is designed for negative ground 12V DC operation only. Use speakers with an impedance of 2 or 4 Ohms ( 2 to 4 Ohm when used as bridging amplifier ) Avoid installing the unit where: -It would be subject to high temperatures, such as from direct sunlight or hot air from the heater. -It would be exposed to rain or moisture. -It would be subject to dust or dirt. If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car, allow the unit to cool off before operation. When installing the unit horizontally, be sure not to cover the heatsink fins with the floor carpet. If this unit is placed too close to the car radio, an interference may occur. In this case, separate the amplifier from the car radio. This power amplifier employs a protection circuit to protect the transistors and speakers if the amplifier ma lfunctions. Do not attempt to test the protection circuits by covering the heatsink or connecting improper loads. Do not use the unit with a weak auto battery as its optimum performance depends on a normal battery supply voltage. For safety reasons, keep the volume of your car audio system moderate so that you can still hear normal traffic sounds outside your car. FUSE REPLACEMENT If the fuse blows, check the power connection and replace the f use. If the fuse blows again after replacement, there may be an internal malfunction. In this case, consult your dealer. WARNING: Use the specified amperage fuse. Use of a higher amperage fuse may cause serious damage. After the amplifier has been installed and all connections have been made careful -lyand securely, turn the radio on so that the amplifier is switched on automatically. After a short power-on period, the amplifier reaches its full performance. Now turn up the volume slowly using the volume control of the radio. If there is no sound or only a distorted replay, switch off the radio immediately, the amplifier will also switch off automatically, and check if all connections have been made correctly. POWER=LED POWER INDICATOR After the orderly connection of the three power terminals, the LED indicator shines green and goes out with off. PROTECT =LED PROTECTION INDICATOR This set is equipped with an overload protection, immediately upon overloading due to short circuit or much increased temperature the overload protection is activated and the red LED indicator is shining. Through this the amplifier is protected against damage. In case of the thermal protection a certain short cooling time must be allowed after which the amplifier automatically resumes operation. LEVEL CONTROL The input level control allows the system to work well within a wide range of output level. Choose the adjustment in the way that you achieve a sound most possibly without any distortion. as a guideline the following procedure is recommended: If you use several amplifier, the adjustment has to be made for each set separately, tune up the volume of your car radio to 2/3 of the maximum volume. Now turn the gain control of the amplifier from " Min " to " Max " direction until you can hear distortions. Then turn the level control a little back to " Min ". The gain control adjustment is finished now. Attention! If you use 2 Ohm speakers in stereo mode. Tri-mode or 4 Ohm speakers in bridge mode and the overload protection is triggered, turn the gain control to " Min " direction, until the operation is free of trouble. HIGH PASS AND LOW PASS CONTROLS This amplifier has high pass and low pass controls for making good sound combination. PROTECTION CIRCUIT: This amplifier is provided with a protection circuit which operates in the following cases when: the unit is overheated. the speaker terminals are short circuited. 6 23 WIRING INSTRUCTIONS STEREO MODE POWER CONNECTION The battery terminal (+12V) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse block ) will reduce the power output and may cause noise and distortion. Use only #10 gauge or thicker (smaller gauge # ) wire for this lead and connect it to the terminal of the battery after all other wiring is completed. GROUND CONNECTION The ground terminal (GND) connection is also critical to the correct operation of the amplifier. Use a wire of the same gauge as the power connection ( #10 or thicker)and connect it between the ground terminal (GND ) of the amplifier and a metal part of the vehicle close to the mounting location. This wire should be as short as possible and any paint or rust at the grounding point should be scraped away to provide a clean metal surface to which the end of the ground wire can be screwed or bolted. REMOTE TURN-ON CONNECTION The amplifier is turned on by applying +12V to the remote turn-on terminal (REM). The wire lead to this terminal should be connected to the "Auto-Antenna " lead from the car stereo which will provide the +12V only when the car stereo is turned on. If the car stereo does not provide an Auto-Antenna" lead, the remote turn-on lead may be wired to an "Accessory " or "Radio "terminal in the car's fuse block. This will turn the amplifier on and off with the ignition key, regardless of whether the car stereo is on or off. The remote turn-on lead does not carry large currents. So #20 gauge wire may be used for this application. SPEAKER CONNECTIONS Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications #18gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess of 10 feet # 16 gauge is recommended. When wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain they correspond to the polarity of the corresponding terminals on the amplifier. Do not ground any speaker leads to the chassis of the vehicle. INPUT CONNECTIONS This amplifier features low-level input capability. If the car stereo does not provide low-level outputs, the amplifier may be connec -ted via the speaker (high-level) outputs from the stereo with a AUTOCRAFT line converter. 22 ZO1500.4/ZO2000.4/ZO3000.4/ZO4000.4/ZO5000.4/ZO6000.4 LPF HPF 50Hz 400Hz LPF INPUT CH3/CH4 BASS BOOST MODE HPF FULL 12 50Hz OUTPUT CH4 INPUT CH2 CH1/CH2 MODE CH2 GAIN 6 400Hz FULL 0 HI INPUT Min PWR HPF GAIN Max Min CH3 CH1 Max PRO HPF HI INPUT 50Hz 400Hz CH1 CH3 + - - + CH4 CH1 + - - + CH2 CH4 CH3 CH1 CH2 CAR STEREO ZO1000.2/ZO1500.2/ZO2500.2/ZO4500.2 INPUT HI INPUT OUTPUT R R L L + - - + L R BASS BOOST 0 Min MODE LPF GAIN 6 12 Max HPF FULL 50Hz 400Hz LPF PWR PRO HPF 50Hz 400Hz L CAR STEREO R 7 STEREO MODE POWER CONNECTION LEADS ZO6000.5 POWER +12V HPF HPF FULL 50Hz 4KHz 50Hz 4KHz MODE HI INPUT INPUT CH3/CH4 GAIN Min Max Min Max HPF FULL R + - - + CH3/CH4 HI INPUT + - - + CH2 CH4 CH1/CH2 CH1 CH3 GAIN + - - + L/R REM GND PWR PRO Min CH5 Max L L CH2 CH1 CH3 CH4 400Hz LPF ZO6000.5 0dB +18dB REMOTE BASS BOOST CH5 R CH5 HEAD UNIT CAR STEREO LINE OUT BRIDGED R IN Min Max GAIN OFF 25Hz SUB SONIC 0O 180 PHASE L O 15Hz 400Hz 0dB +18dB LPF BASS BOOST REMOTE OUT L CAR STEREO R 8 BATTERY DC 12V NOTES ON THE POWER SUPPLY : LINE INPUT PRO + to a metal part of car ZO3000.1D/ZO5000.1D/ZO8000.1D PWR FUSE 15Hz MODE GAIN CH1/CH2 ( +12V) REMOTE OUT HPF Connect the +12V power input lead only after all other leads have been connected. Be sure to connect the ground wire of the unit securely to a metal part of the car. A lose connection may cause a malfunction of the amplifier. REM: The unit is turned on by applying +12 Volts to this terminal. This terminal does not draw heavy current like the Power Terminals so a thinner connecting wire is acceptable. Standard 18 GAUGE is fine and the standard color is yellow .lf the radio is equipped with a Power Antenna control wire, it can drive this terminal . If the Power Antenna wire is already in use, you can still splice into it. With this method, the unit will turn on automatically with the radio. Use the power supply lead with a fuse attached whose value is the same as original fuse. Place the fuse in the power supply lead as close as possible to the car battery . During a full power operation, maximum current will run through the system Therefore, make sure that the leads to be connected to the +12V and GND terminals of the unit respectively must be larger than 10-Gauge ( AWG.10). 21 SPEAKERS CONNECTIONS BRIDGED MODE ZO1500.2/ZO2500.2 ZO1500.4/ZO2000.4/ZO3000.4 MONO SPEAKER 4~8Ohm ZO1500.2:30AX2 ZO2500.2:40AX2 BRIDGED LEFT REM +12V GND OUTPUT POWER Ch2 SPEAKER 2~4Ohm SPEAKER OUTPUT SPEAKER FUSE RIGHT Ch1 SPEAKER 2~4Ohm INPUT CH1 CH3 ZO4500.2 CH2 BRIDGED FUSES BRIDGED SPEAKER REM +12V RIGHT REM POWER CH4 Ch3 SPEAKER 2~4Ohm LEFT +12V Ch4 SPEAKER 2~4Ohm GND INPUT ZO1500.4:30Ax2 ZO2000.4:35Ax2 ZO3000.4:40Ax2 GND ZO4000.4 OUTPUT POWER INPUT Ch1 SPEAKER 2~4Ohm ZO4500.2:200A Ch2 SPEAKER 2~4Ohm MONO SPEAKER 4~8Ohm ZO6000.5 SPEAKER OUTPUT CH1 CH5 CH2 SPEAKER OUTPUT SPEAKER CH3 BRIDGED CH4 MIN 1 REM +12V GND OUTPUT POWER INPUT CH1 CH3 BRIDGED CH2 FUSES CH4 40A X 3 Ch3 SPEAKER 2~4Ohm POWER Ch4 SPEAKER 2~4Ohm ZO6000.5:150A MONO SPEAKER 4~8Ohm 20 +12V 9 REM GND INPUT SPEAKERS CONNECTIONS BRIDGED MODE ZO5000.4 MONO SPEAKER 4~8Ohm ZO5000.4 Ch1 SPEAKER 2~4Ohm Ch2 SPEAKER 2~4Ohm CH2 FUSES +12V REM SPEAKER OUTPUT SPEAKER OUTPUT CH1 GND CH1 CH3 CH3 BRIDGED CH4 40A X 4 Ch3 SPEAKER 2~4Ohm POWER BRIDGED FUSES CH4 40A X 4 REM +12V POWER GND INPUT INPUT Ch4 SPEAKER 2~4Ohm MONO SPEAKER 4~8Ohm ZO6000.4 SPEAKER OUTPUT ZO6000.4 CH1 CH2 CH3 Ch1 SPEAKER 2~4Ohm CH2 BRIDGED REM +12V POWER CH4 GND INPUT Ch2 SPEAKER 2~4Ohm ZO6000.4:200A SPEAKER OUTPUT CH1 CH3 Ch3 SPEAKER 2~4Ohm CH2 BRIDGED +12V POWER CH4 Ch4 SPEAKER 2~4Ohm REM GND ZO1000.2 MONO SPEAKER 4~8Ohm MONO SPEAKER 4~8Ohm INPUT ZO6000.4:200A LEFT BRIDGED SPEAKER RIGHT FUSE REM GND OUTPUT 40A 10 +12V 19 POWER INPUT SPEAKERS CONNECTIONS BRIDGED MODE ZO1000.2 ZO1500.4/ZO2000.4/ZO3000.4 LEFT SPEAKER 2~4Ohm MONO SPEAKER 4~8Ohm SPEAKER OUTPUT CH1 CH2 FUSES +12V REM GND RIGHT SPEAKER 2~4Ohm LEFT BRIDGED SPEAKER CH3 BRIDGED POWER CH4 FUSE RIGHT +12V REM GND OUTPUT INPUT POWER 40A INPUT ZO1500.4:30Ax2 ZO2000.4:35Ax2 ZO3000.4:40Ax2 MONO SPEAKER 4~8Ohm ZO1500.2/ZO2500.2 ZO4000.4 MONO SPEAKER 4~8Ohm LEFT SPEAKER 2~4Ohm SPEAKER OUTPUT CH1 FUSES CH2 +12V REM RIGHT SPEAKER 2~4Ohm GND LEFT CH3 BRIDGED 40A X 3 CH4 POWER BRIDGED FUSE RIGHT +12V OUTPUT POWER ZO1500.2:30AX2 ZO2500.2:40AX2 18 GND INPUT SPEAKER MONO SPEAKER 4~8Ohm REM 11 INPUT SPEAKERS CONNECTIONS SPEAKERS CONNECTIONS AT BRIDGED ZO8000.1D ZO4500.2 LEFT SPEAKER 2~4Ohm AMP 1 MASTER RIGHT SPEAKER 2~4Ohm PWR LINE OUT LINE INPUT BRIDGED R PRO LEFT BRIDGED SPEAKER REM +12V RIGHT IN Min Max GAIN GND OFF 25Hz SUB SONIC 0 O 180 O 15Hz 400Hz 0dB +18dB PHASE LPF BASS BOOST REMOTE L OUT OUTPUT POWER INPUT ZO4500.2:200A ZO6000.5 CAR STEREO CH1 CH5 CH2 SPEAKER OUTPUT SPEAKER CH3 BRIDGED CH4 MIN 1 REM +12V GND AMP 2 S L AVE PWR OUTPUT POWER INPUT LINE OUT LINE INPUT BRIDGED R PRO IN Min Max GAIN OFF 25Hz SUB SONIC 0 O 180 O 15Hz 400Hz 0dB +18dB PHASE L OUT ZO6000.5:150A 12 LPF BASS BOOST REMOTE 17 SPEAKERS CONNECTIONS SPEAKERS CONNECTIONS AT BRIDGED ZO8000.1D ZO3000.1D/ZO500.1D MONO SPEAKER 1~4Ohm AMP 1 + FUSES +12V REM GND FUSES SPEAKER +12V REM GND OUTPUT MIN 1 30A X 4 POWER INPUT SPEAKER OUTPUT POWER MIN 1 ZO3000.1D:30Ax3 ZO5000.1D:35Ax3 To a metal part of car 4~8Ohm INPUT ZO8000.1D BATTERY DC 12V MONO SPEAKER 1~4Ohm + FUSES +12V REM GND AMP 2 SPEAKER OUTPUT MIN 1 FUSES SPEAKER +12V REM 30A X 4 GND OUTPUT MIN 1 30A X 4 16 POWER INPUT 13 POWER INPUT SPEAKERS CONNECTIONS AT BRIDGED SPEAKERS CONNECTIONS AT BRIDGED ZO3000.1D/ZO500.1D ZO3000.1D/ZO500.1D AMP 1 AMP 1 MASTER FUSES +12V REM PWR GND LINE OUT LINE INPUT BRIDGED R PRO IN Min Max SPEAKER OFF 25Hz SUB SONIC GAIN 0 O 180 O 15Hz 400Hz 0dB +18dB PHASE LPF BASS BOOST REMOTE L OUTPUT POWER MIN 1 OUT INPUT ZO3000.1D:30Ax3 ZO5000.1D:35Ax3 4~8Ohm To a metal part of car BATTERY DC 12V CAR STEREO AMP 2 AMP 2 S L AVE FUSES +12V REM GND PWR LINE OUT LINE INPUT BRIDGED R PRO IN Min Max GAIN SPEAKER OUTPUT OFF 25Hz SUB SONIC L POWER MIN 1 14 0 O 180 O 15Hz 400Hz 0dB +18dB PHASE LPF BASS BOOST REMOTE OUT INPUT 15