Transcript
ZONE-120/240/360/480/600 A.T.T. 6 Zone Mixing Amplifier
Better Communication
Safety Precautions In using the present device, please keep the following safety regulations in order to prevent any hazard or material damage.
Don’t
CAUTION
Low level of risk which could lead to minor or moderate injury.
Don’t dissemble Keep off Strongly Recommended
WARNING
High level risk that could result in death or serious injury.
Unplug Electricity Warning Fire Warning
CAUTION Do not plug several products in one multi-outlet.
Do not bend cable by force or leave it under any heavy object.
Do not touch plug with your hands wet.
- This can provoke over-heating and a fire.
- A damaged cable can cause a fire.
Keep the device away from water or humid area.
Unplug the device when in thunderstorm.
Don’t use non-Pascom products connected with ours.
- This might cause damage to products and/or start a fire.
- It may cause damage to products and/or start a fire.
When not in use for a long time, leave the device unplugged. - This is recommended to extend device’s life.
To help ventilation and avoid over-heating, install this device at least 5~10cm off from walls.
WARNING! Never dissemble or take apart device! In case service is needed, contact authorized repair person only.
In case smoke or unusual noise is found, unplug immediately and contact authorized repair person.
Make sure ventilation hole is clear from any external metal piece (e.g. coin) or flammable object (e.g. paper or matchstick)
In case using DC power, make sure to use correct power and direction of batteries.
CAUTION Fix plug tight into outlet. Unstable plug might cause a fire.
If power cable needs to be cut and re-connected, make sure power is off and device is unplugged. It can be very dangerous.
When unplugging, never pull string. Make sure to hold plug. Inner cable might cut inside covering.
In case AC switch breaker is needed, be cautions with electricity.
In case DC power is used, make sure with power voltage and current at every time.
Make sure device is away from heat or direct rays of the sun. It might cause a fire.
For installation, use only provided screws and bolts to fix firmly.
DC
Clean device with only DRY cloth.
Don’t drop any object onto the device. Keep it away from magnets. This might cause damage to the device.
Device should be used only within certified distance, by provided cables only. This helps performance.
Warrantee terms and conditions vary by country and may not be the same for all products. For specific warranty information about warranty or service, contact Pascom co.,ltd directly or authorized distributor for your country or region.
ATT 6 ZONE MIXING AMPLIFIER
SPECIAL FUNCTION ① 6 ZONE SPEAKER OUTPUT 6 Speaker selector and 1 All Speaker button for selective zone addressing or all-area addressing. Output power adjustable individually. ② PRIORITY FUNCTION MIC1, MIC ALL, CHIME/SIREN and REMOTE AMP are prior to other signals. (other sources are automatically muted) ③ 4-TONE CHIME 2 type 4-tone Chime is provided to use before and after announcement. Convenient external chime terminal. ④ EMERGENCY ADDRESS Automatic fire evacuation address is released as fire signal is received from contact type fire signal receiver. ⑤ REMOTE POWER Power is turned on/off by convenient remote control.
4. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
Front Panel ①
②
③
④
⑤⑥
⑦
⑧
ZONE -600 A.T.T 6 Zone Mixing Amplifier
⑨ ⑩ ⑪ ⑫
⑬⑭ ⑮
1.USB MEMORY TERMINAL Compatible with USB memory or USB HDD. (HDD has to be FAT 32 format and partitioned into 40 Gbytes to be found by the device.) 2.REMOTE SIGNAL RECEIVER Receives remote controller signal of DVD Player remote controller. 3.VFD DISPLAY Displays status of DVD or USB file. 4.DISC TRAY Stores and plays disc 5. DVD, USB Play button - OPEN/CLOSE disc tray. - PLAY/PAUSE disc. - STOP playing disc. - PREV : Plays previous track - NEXT : Plays next track. - REPEAT files in disc or USB memory.
6. DVD VOLUME CONTROLLER 7. ZONE SELECTOR - 6 Zone Selectors and 1 ALL CALL button. - Attenuator adjusts output power.
ATTENUATOR
1
2
3
4
5
6
OUTPUT POWER
8.9V
12.5V
25V
50V
70V
100V
ZONE-120/240/360/480/600 .5
ATT 6 ZONE MIXING AMPLIFIER
8. MONITOR SPEAKER VOLUME CONTROLLER 9. LED DISPLAY - EM turns on when fire alarm signal is received. - PHANTOM turns on when PHANTOM button in rear panel is on. - PROTECTION turns on when protective circuit recognizes error. * TEL lamp is not in use
10. OUTPUT LEVEL LED DISPLAY Turn down output volume in case CLIP LED turns on and helps protect the device. 11. STAND-BY/POWER LED DISPLAY Green light is on for stand-by mode. Press POWER button to start operation, and LED turns red.
12. POWER BUTTON Provides power and device starts operation. 13. CONDENSER MICROPHONE VOLUME CONTROLLER 14. CONDENSER MICROPHONE Internal condenser microphone. Talk into this part when addressing. 15. TALK Turns on condenser microphone. Hold while address is being made. Release when finished. 16. 6 CHANNEL EQUALIZER AND VOLUME CONTROLLER Provides ± 10 dB control of BASS(100Hz) and TREBLE(10KHz) 17. CHIME VOLUME 2way 4-tone chime release button and its volume controller. Useful before and after announcement is made. 18. SIREN VOLUME In case of emergency, you can release siren and adjust its volume. (~) : undulating tone siren (-) : one tone siren 19. MASTER VOLUME CONTROLLER Controls the volume of finally mixed sound by individual adjustment.
6. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
Rear Panel ①
⑬
②
REMOTE AMP
AUDIO OUTPUT 6
5
4
3
2
1
100V
Sig _
Sig+
4
CHIME
③
④
FIRE FL
GND
CEN
SL
SUB
SR
L
Y
Pb/Cb
Pr/Cr
R
COAX
VIDEO
S-VIDEO
RS232
485 +
COM
AMP IN
PC IN (ST)
PRE OUT
PC IN (BAL)
AC 240V/50Hz,1700W FUSE(T10AL,250V) AC 230V/50Hz,1700W FUSE(T10AL,250V) AC 220V/60Hz,1700W FUSE(T10AL,250V)
485 _
485 _
FR
L
5.1CH
CLASS I LASER PRODUCT
LINE IN
6 S/N XX
485 +
GND
5
4
GAIN
3
GAIN
2CH
2
GAIN
VIDEO
1
OPT
GAIN
MIC PRIORITY OFF
EM OUTPUT
POWER ON
DC POWER + 24V
_
10
REC OUT
-
FUSE INSIDE
⑤
50
_
10
_
50
_
10
_
50
_
10
_
50
ALL
PC LINK
MIC1 TALK
R
~AC INPUT
_
PHANTOM
+
PHANTOM
PHANTOM
PHANTOM MADE IN KOREA
⑥
⑦
⑧
⑨
⑩
⑪
⑫
1. SPEAKER TERMINAL Pick 4 Ω output terminals or Zone 1~6, 100V terminals, so overload is prevented. (*Note: Only Zone 1~6 terminals are controlled by SPEAKER SELECTORS on front panel.)
MODEL
40hm
100V
ZONE 1~6
Maximum output power per zone
ZONE- 120
21.9V
83.3 Ohm
83.3 Ohm
20W
ZONE- 240
31V
41.7 Ohm
41.7 Ohm
40W
ZONE- 360
37.9V
27.8 Ohm
27.8 Ohm
60W
ZONE- 480
43.8V
20.8 Ohm
20.8 Ohm
80W
ZONE- 600
49V
16.7 Ohm
16.7 Ohm
100W
2. REMOTE CONTROL INPUT TERMINAL - If remote address is wanted, connect REMOTE AMP terminal with remote amplifier (DRA-9600). - Top line: SIG+,SIG- and GND for vocal signals, FIRE terminals for automatic emergency evacuation address by short circuit. - Bottom line: left side 485+,485- and GND for remote amplifier and other line signals. (Right side 485+ and 485- are not in use) - Connect CHIME with remote chime release button.
ZONE-120/240/360/480/600 .7
ATT 6 ZONE MIXING AMPLIFIER
3. RS232 TERMINAL Enables PC control in short distance. (*Only master volume and zone selection is available) 4. DVD OUTPUT TERMINAL Enables sound and/or visual control of DVD player. Connects with external receiver or LCD TV. *Refer to “HOW TO CONNECT” for detail. 5. POWER INPUT Connects with power cable. *Double check power voltage before connecting! 6. EM OUT Sends fire alarm contact signal in case of emergency. 7. POWER ON Enables remote power control. 8. DC INPUT Connects with DC power(+24 V) battery for temporary use. Make sure with polarity(+/-). Cables have to be diameter of 3.0mm or over, and length of 8m or less. (power loss ≤1V, FUSE is F3, F4 on POWER PCB) - Capacity Remarks: ZONE-120 : T10A/250V ZONE-240 : T20A/250V ZONE-360 : T15A/250V X 2 ZONE-480 : T20A/250V X 2 ZONE-600 : T25A/250V X 2 9. EXTERNAL DEVICE JACK - AMP IN : When connected, all other speaker output is muted but only signals by this connection is released. - PRE OUT, REC OUT : Used for another external device to record sound of this device, or used for another amplifier by parallel connection. * REC OUT level is -10dB, PRE OUT level is 0dB. - PC IN ST/BAL : receives sound signal from PC. * PC connection remarks: STEREO Jack with TIP(LEFT), RING(RIGHT), SLEEVE(GND) BALANCE with TIP(HOT), RING(COLD), SLEEVE(GND) - PC OUT : When connected, PC signals received can release to linked amplifier. (BALANCED)
8. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
10. LINE INPUT 5, 6 JACK Connects with Line level device. Input Level is -20 dB (STEREO)
11. MIC, LINE INPUT 1~4. INPUT 1~4: either microphone or line available. Individual power button for phantoms. Input GAIN ranges -10dB ~ -50dB. *XLR connector is needed to use phantom powered condense microphone. (phantom power can’t be used by ¼” phone jack.) * CAUTION! In case phantom power is used, strong impulse noise might damage speakers. It is recommended to minimize GAIN volume and master volume on front panel before turning on phantom power. Also, make sure phantom power is off before connecting/disconnecting microphone and avoid strong impulse noise.
12. PRIORITY ALL : Microphone and Chime/Siren are prior to other signals MIC1 / TALK : Microphone 1, condenser microphone and Chime/Siren are prior to other signals. OFF : Only Chime/Siren is prior to other signals. * General Address Priority 1. Fire Evacuation,Chime/Siren, Remote Amp, PC In. 2. Mic (Set by PRIORITY Switch) 3. Line 5/6 DVD Player.
13. TELEPHONE Connect INPUT terminal with trunk or telephone switcher LINE. Connect LINK terminal with regular telephone and now it is ready to use. When ring signal is sent to INPUT terminal, ring tone will release to the selected zone. During ring signal INPUT, double check ZONE SELECTOR lamps. This will help avoid malfunction and operate system properly. You can adjust Ring signal volume by Chime Volume knob on front panel.
ZONE-120/240/360/480/600 .9
ATT 6 ZONE MIXING AMPLIFIER
DVD PLAYER OPERATION
10. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
REMOTE CONTROLLER ① Power On/Off ② Video mode selector(Composite, Component, S-Video, VGA)
2
3
VIDEO MODE
N/P
REPEAT
A-B
RANDOM
USB/DVD
LANGUAGE
SUBTITLE
ANGLE
R/L
REV
FWD
PREV
NEXT
1
③ TV system mode selector (NTSC, PAL)
4
④ Open/close CD tray ⑤ REPEAT : One or all Track A-B : Repeat section
POWER
OPEN/CLOSE
RANDOM : Select and play randomly USB/DVD : Select button LANGUAGE : Voice language select
5
SUBTITLE : Caption language select ANGLE : Convert the angle of DVD image R/L : Right/left selector for output
6
SETUP
MENU
⑥ REW : Rewind track during playback FWD : Forward track during playback PREV : Move to previous track NEXT : Move to next track
7
ENTER
SETUP : Setup system preference MENU : Display DVD menu during playback ⑦ Move or select the menu title
TITLE
PBC
PBC : Display index of tracks in VCD TITLE : Display index of tracks in DVD ⑧ ZOOM : Enlarge or downsize the image in
8
play
ZOOM
PLAY/PAUSE
STOP
RETURN
SLOW
STEP
PROG
CLEAR
1
2
3
4
5
6
7
8
9
0/10
10+
TIME
VOL-
VOL+
PLAY/PAUSE : to play or pause STOP : Stop playing RETURN : stop playback and move back to
9
previous menu SLOW : Play image slowly STEP : Play video by scene
10
OSD
MUTE
PROG : sort playlist by the title, chapter, or music ⑨ 1~10 : Select track to play. TIME : Displays proceeding/remaining time in current play. ⑩ OSD : Display caption on TV in configuration MUTE : Mute/unmute sound VOL + - : Controls the volume
ZONE-120/240/360/480/600 .11
ATT 6 ZONE MIXING AMPLIFIER
How to use DVD, CD DISC Available types of media and usage - DVD, DVD-R, DVD+R, DVD_RW, CD, HDCD, CD-R, CD+R, CD_RW, MP3 CD, AVI CD, JPG CD ① Open the tray using the OPEN/CLOSE button, and press the OPEN/CLOSE button after putting CD or DVD into the tray. ② If CD or DVD aren't on the tray or there is some problem, the screen shows "NO DISC" ③ Play CD or DVD as pressing the PLAY/PAUSE button. ④ If you press the PLAY/PAUSE button during playing, it will pause. ⑤ If you press the STOP button once during playing, CD or DVD will stand by in the PRE STOP state. ⑥ By pressing the PLAY/PAUSE button in the PRE STOP state, CD or DVD replay and they stop completely by pressing the STOP butthzon. - In case DISC is already on the tray when you power on ① It reads the track on the DISC. ② After selecting the desired DISC, operate by pressing the PLAY button. PLAY Function ① After inserting a DISC, press the PLAY button. ② Start playing the DISC. ③ By pressing the REPEAT button of the remote control, the selected track will be played back repeatedly. OFF ---> Repeat one ---> Repeat All ---> OFF ④ By using the A-B button of the remote control, a designated section will be repeated. Repeat OFF ---> Repeat A- ---> Repeat A-B ---> Repeat OFF ⑤ Finish the playing when all music has played. Repeat Function - Become the repeat function by pressing the REPEAT button of the remote control while playing CD or DVD. ① When starting The repeat function is OFF state. Operate it by pressing the PLAY button. ② During a general operation The repeat function operates by pressing the REPEAT button. OFF ---> Repeat one ---> Repeat All ---> OFF ---> .... ③ REPEAT ONE ☞ The selected track will be played back repeatedly. ④ REPEAT ALL ☞ All music of the inserted disc will be played back repeatedly.
12. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
A-B Section-Repeat Function - By designating the area of section-repeat using the A-B button, it plays the designated section repeatedly. ① When starting Operate by pressing the PLAY button. ② During a general operation Designate by pressing the A-B button at the start point of the repeat section. Designate by pressing the A-B button at the end point of the repeat section. ☞ - Repeat Cancel ---> set A point(press A-B button) ---> set B point(press A-B button) ---> A-B Repeat.... RANDOM Function - Select and play a music of the inserted disc at discretion by pressing RANDOM button.
SEARCH Function -Wind faster forward or backward by pressing the SEARCH button ◀◀,▶▶ during playback. ☞ The winding speed is adjusted by X2, X4, X8, X20 in speed unit as pressing this button once. STEP Function -A movie changes to a pause picture by each scene as pressing the STEP button once while playing DVD movie. SLOW Function -A movie changes to a pause picture by each scene as pressing the SLOW button while playing DVD movies. ☞ It is adjusted by 1/2, 1/3, 1/4, 1/5, 1/6, 1/7 in 6 step as pressing the SLOW button. ZOOM Function - Enlarge/Reduce the picture screen by pressing the ZOOM button while playing DVD movies. ☞ It is adjusted by zoom2, zoom3, zoom4, zoom1/2, zoom1/3, zoom1/4 in 6 step as pressing the SLOW button.
ZONE-120/240/360/480/600 .13
ATT 6 ZONE MIXING AMPLIFIER
How to operate USB - Play MP3 file You can play USB Memory or HDD. HDD has to be formatted with FAT32. Especially, external HDD has to be partitioned into every 40 Gb, too. 3.5 inch HDD with its own power supply is recommended. 2.5 inch HDD might not be found when its power consumption is bigger than power supply. USB Memory made by certain manufacturers might not be found.
- Play AVI file You can play DIVX of AVI format. Clips might break up, play slowly or won't start according to capacity and resolution of each file.
- Play JPG file You can play JPG images in USB memory or HDD.
14. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
How to connect with Channel System ◆ Make sure that this device and Receiver are both turned off and unplugged.
FL
FR
CEN
SL
SUB
SR
5.1CH
L
Y
Pb/Cb
R
COAX
VIDEO
2CH
Pr/Cr
S-VIDEO
VIDEO
OPT
Receiver rear panel 5.1IN
FL
FR
1. 2. 3. 4.
CEN
SL
SUB
SR
CD
FL
CE
SL
L
FR
SW
SR
R
L
Y
Pb/Cb
R
COAX
VIDEO
5.1CH
2CH
1
2
5.1 CH Analog Speaker Jack Stereo Jack(Regular TV, 2CH) COAXAL jack Regular TV VIDEO jack
S-VIDEO
VIDEO
3
4
7
Pr/Cr
OPT
5
6
5. S-Video Logic 6. Optical terminal 7. Component Jack for HD TV
▶ By provided RCA cable, you can connect with receiver, amplifier or other stereo input Jack. Red into Right, White into Left.
ZONE-120/240/360/480/600 .15
ATT 6 ZONE MIXING AMPLIFIER
How to connect with a regular TV ◆ Make sure that this device and TV are both turned off and unplugged.
VIDEO L SOUND R
VIDEO Yellow
SOUND White Red
L
FL
FR
CEN
SL
SUB
SR
5.1CH
R
L
Y
Pb/Cb
R
COAX
VIDEO
2CH
Pr/Cr
S-VIDEO
VIDEO
OPT
▶ Plug in 3-colored RCA connector cable into female jack on the rear panel of the device. ▶ Yellow is for [VIDEO] jack, red is right sound channel for [R] jack, and white is left sound channel for [L] jack. In case of mono TV, either red or white is fine. ▶ Change TV mode to [EXTERNAL INPUT] mode by your TV remote controller.
16. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
How to connect with a HD TV ◆ Make sure that this device and TV are both turned off and unplugged. ◆ In case of component connection, change video setting to [COMPONENT]mode. You can adjust on [SETTING] or by using device remote controller's [VIDEO MODE] button.
SOUND White Red
L
FL
FR
R
CEN
SL
SUB
SR
5.1CH
Green
VIDEO Blue
Red
Y
Pb/Cb
Pr/Cr
L
Y
Pb/Cb
R
COAX
VIDEO
2CH
Pr/Cr
S-VIDEO
VIDEO
OPT
▶ Plug in each connector into relevant component jack on rear panel of the device. Green into Y, blue into Pb/Cb, Red into Pr/Cr. ▶ Plug in 3 colored RCA connector cable into 2CH jack on rear panel of the device. Red into L, White into R. (Yellow is not used) ▶ Turn on TV and the device, change video mode on SETTING: [SYSTEM SETUP]☞ [VIDEO]☞[P-SCAN YPBPR]. If there is no signal, use device remote controller's [VIDEO MODE] button and change to [P-SCAN YPBPR] mode.
ZONE-120/240/360/480/600 .17
ATT 6 ZONE MIXING AMPLIFIER
5.1 How to connect with Channel Analog System ◆ Make sure that this device and receiver are both turned off and unplugged.
FL
FR
CEN
SL
SUB
SR
5.1CH
L
Y
Pb/Cb
R
COAX
VIDEO
2CH
Receiver rear panel
Pr/Cr
S-VIDEO
VIDEO
5.1IN
OPT
CD
FL
CE
SL
L
FR
SW
SR
R
▶ Connect 5.1CH output signal with receiver as the picture above and enjoy spectacle 3D sound. ▶ Connector cable is not provided in this package. Please purchase separately.
18. ZONE-120/240/360/480/600
ATT 6 ZONE MIXING AMPLIFIER
SPECIFICATION ■ OUTPUT POWER
------------------------------------------------------------
360W
■ INPUT SENSITIVITY MIC 1~4 ------------------------------------------------------------------
-54dB
LINE 1~4 -----------------------------------------------------------------
-14dB
LINE 5~6 -----------------------------------------------------------------
-16dB
PC IN(ST) -----------------------------------------------------------------
-10dB
PC IN(BAL) ----------------------------------------------------------------
-10dB
■ FREQUENCY RESPONSE MIC 1~4 ----------------------------------------------------------- 100Hz ~ 14KHz LINE 1~4 ------------------------------------------------------------ 90Hz ~ 16KHz LINE 5~6 ------------------------------------------------------------ 90Hz ~ 18KHz SIREN ----------------------------------------------------------------
630Hz
■ SIGNAL TO NOISE (on WTD 30KHz) MIC -------------------------------------------------------------
Better than 55dB
LINE -------------------------------------------------------------
Better than 70dB
■ TOTAL HARMONIC DISTORTION (on WTD 20KHz) ---------------------------- Less than
■ POWER SOURCE
1%
--------------------------------------------- ~AC 230V/50Hz, DC 24V
■ POWER CONSUMPTION ----------------------------------- ZONE-360 : 380W(1/8 POWER) ■ DIMENSION -------------------------------------------------- 482(W)x88(H)X340(D)mm ■ WEIGHT -------------------------------------------------------------------- 21 Kg
ZONE-120/240/360/480/600 .19
ATT 6 ZONE MIXING AMPLIFIER
NOTE.
20. ZONE-120/240/360/480/600
Better Communication
MADE IN KOREA
www.ipascom.com
